Краткое содержание страницы № 1
P-2301/2R-P1C
VoIP ATA / Station Gateway
P-2301RL-P1C
VoIP ATA / Station Gateway with Lifeline
User’s Guide
Version 3.60
3/2007
Edition 1
Copyright © 2007. All rights reserved
Краткое содержание страницы № 2
P-2301/2R-P1C / P-2301RL-P1C User’s Guide 1 Overview This guide helps you set up and use your ZyXEL P-2301R- P1C, P-2301RL-P1C or P-2302R-P1C (the “ZyXEL Device”). This guide contains the following sections: Section Page Description Installation 4 A checklist of things you need before you Requirements install the ZyXEL Device. Making Hardware 5 How to connect the ZyXEL Device to your Connections network, your computer and telephone(s). Initial 6 How to configure your ZyXEL Device to Configur
Краткое содержание страницы № 3
P-2301/2R-P1C / P-2301RL-P1C User’s Guide The following figure shows a typical way to use your ZyXEL Device. • When you make a phone call over the Internet, you use a telephone (A) to dial the number. The P-2301R-P1C and P- 2301RL-P1C support one telephone connection, and the P- 2302R-P1C supports two telephone connections. The telephone is connected to your ZyXEL Device (C), which is connected to the broadband modem or router that pro- vides Internet access (D). • When you want to use the In
Краткое содержание страницы № 4
P-2301/2R-P1C / P-2301RL-P1C User’s Guide • P-2301RL-P1C only: use your telephone (A) to make calls over the regular telephone network (PSTN or Public Switched Telephone Network). The following table contains useful information about your ZyXEL Device. Default management IP 192.168.1.1 Address Default Subnet Mask 255.255.255.0 Default Password 1234 2 Installation Requirements Make sure you have the following things before you set up your ZyXEL Device. • Internet access - account information
Краткое содержание страницы № 5
P-2301/2R-P1C / P-2301RL-P1C User’s Guide 3 Making Hardware Connections 1LINE (P-2301RL-P1C only): Use a telephone cable to connect the telephone jack to this port. 5
Краткое содержание страницы № 6
P-2301/2R-P1C / P-2301RL-P1C User’s Guide 2 PHONE / PHONE 1: Use a telephone cable (and any telephone adaptor provided with your ZyXEL Device) to connect your telephone to this port. 3 PHONE 2 (P-2302R-P1C only): connect another telephone to this port. If you have only one phone, use the PHONE 1 port. 4ETHERNET: Use an Ethernet cable to connect your computer to this port. 5WAN: Use an Ethernet cable to connect your broadband modem or router to this port. 6POWER: Use the power adaptor prov
Краткое содержание страницы № 7
P-2301/2R-P1C / P-2301RL-P1C User’s Guide 2 Enter http://192.168.1.1 as the address. 3 Click Login. 4 Type a new password, re-type it to confirm, and click Apply. The next time you log in, you should not see this screen. 7
Краткое содержание страницы № 8
P-2301/2R-P1C / P-2301RL-P1C User’s Guide 5 Click Go to Advanced setup. 6 The Status screen appears. Click the Wizard icon ( ) in the upper right corner. If the INTERNET light is green, go to section 4.34.3 on page 16. Otherwise, go to section 4.24.2 on page 94.2. 8
Краткое содержание страницы № 9
P-2301/2R-P1C / P-2301RL-P1C User’s Guide 4.2 Connection Wizard If you subscribe to a Roadrunner service, you cannot use the Connection Wizard to set up your Internet connection. In this case, please use the Network > WAN > Internet Connection screen to enter your information. You must have an Internet account set up and ready to use to complete this section. 1 In the Wizard Setup screen, click Connection Wizard. 9
Краткое содержание страницы № 10
P-2301/2R-P1C / P-2301RL-P1C User’s Guide 2 Click Next. 3 System Name is used to identify the ZyXEL Device on the network. Use the default value, unless you know the name is already used in the network. Domain Name (optional): Enter the appropriate name, if there is one, or use the default value. Click Next. 4 This screen has different fields, depending on the connection type (encapsulation) your ISP uses. Select Ethernet or PPP over Ethernet (PPPoE). If you are not sure which type of enca
Краткое содержание страницы № 11
P-2301/2R-P1C / P-2301RL-P1C User’s Guide • If your ISP gave you a user name and password, select PPP over Ethernet. • If your ISP did not give you a username and password, select Ethernet. Then, follow the instructions in the appropriate section below. 4.2.1 Connection Wizard (Ethernet) Follow these steps if your ISP uses an Ethernet connection. 1 Click Next. 2 Select Get automatically from your ISP if your ISP did not give you a static IP address. Then, click Next, and go to step 4 below.
Краткое содержание страницы № 12
P-2301/2R-P1C / P-2301RL-P1C User’s Guide Select Use fixed IP address provided by your ISP if your ISP gave you a static IP address. Then, click Next. 3 Enter the information provided by your ISP. If your ISP did not provide information for any of the fields in this screen, leave them at their default settings. Then, click Next. 12
Краткое содержание страницы № 13
P-2301/2R-P1C / P-2301RL-P1C User’s Guide 4 Select Factory default, unless you need to spoof your computer’s MAC address. Then, click Apply. 5 Click Finish. 6 Launch another web browser, and go to any web site (for example, http://www.zyxel.com). If you cannot access the Internet, see Troubleshooting on page 27. 4.2.2 Connection Wizard (PPP over Ethernet) Follow these steps if your ISP uses a PPP over Ethernet (PPPoE) connection. 13
Краткое содержание страницы № 14
P-2301/2R-P1C / P-2301RL-P1C User’s Guide 1 Enter the information provided by your ISP. If your ISP did not provide information for any of the fields in this screen, leave them at their default settings. Then, click Next. 2 Select Get automatically from your ISP if your ISP did not give you an IP address. Then, click Next, and go to step 4. Select Use fixed IP address provided by your ISP if your ISP gave you a static IP address. Then, click Next, and go to step 3. 14
Краткое содержание страницы № 15
P-2301/2R-P1C / P-2301RL-P1C User’s Guide 3 Enter the information provided by your ISP. If your ISP did not provide information for any of the fields in this screen, leave them at their default settings. Then, click Next. 4 Select Factory default, unless you need to spoof your computer’s MAC address. Then, click Apply. 15
Краткое содержание страницы № 16
P-2301/2R-P1C / P-2301RL-P1C User’s Guide 5 Click Finish. 6 Launch another web browser, and go to any web site (for example, http://www.zyxel.com). If you cannot access the Internet, see Troubleshooting on page 40. 4.3 VoIP Setup Wizard You must have Internet access and a VoIP account before you can complete this section. 16
Краткое содержание страницы № 17
P-2301/2R-P1C / P-2301RL-P1C User’s Guide 1 In the Wizard Setup screen, click VoIP Setup. 2 Enter the information provided by your VoIP service provider. If you have a VoIP account like “1234@VoIP- provider.com”, the SIP Number is “1234”, and the SIP Service Domain is “VoIP-provider.com”. If your VoIP service provider did not provide information for any of the fields in this screen, leave them at their default settings. P-2302R-P1C only: If you want to set up the ZyXEL Device’s second VoIP
Краткое содержание страницы № 18
P-2301/2R-P1C / P-2301RL-P1C User’s Guide Click Apply. P-2302R-P1C Only 3 Wait while the ZyXEL Device tries to register the VoIP account(s). 4 Click Finish. The PHONE light should be green. 18
Краткое содержание страницы № 19
P-2301/2R-P1C / P-2301RL-P1C User’s Guide 4.4 Bandwidth Management Wizard This Bandwidth Management Wizard allows you to specify the amount of bandwidth you allow certain applications to use on the ZyXEL Device. Use this wizard only if you want to ensure that certain applications, such as you VoIP calls, get enough bandwidth. If you want to use the wizard, click Bandwidth Management Wizard in the Wizards screen. The following screen displays. 19
Краткое содержание страницы № 20
P-2301/2R-P1C / P-2301RL-P1C User’s Guide 1 Click Next. In the screen that appears, select the Active checkbox. Enter the total amount of traffic the device can send to the WAN in the Managed Bandwidth (kbps) field. This does not affect the total amount of traffic the device can send to the LAN. You should enter the maximum amount of data the ZyXEL Device can send to the WAN. For example, set this field to 1000 kbps if a broadband device connected to the WAN port has a maximum speed of 1
