Краткое содержание страницы № 1
CyberPro PCI 2S
Quick Installation Guide
Introducing the CyberPro PCI 2S
The CyberPro PCI 2S high-speed serial I/O card provides
two additional 9-pin serial ports. Depending on the
model purchased, this board will fit into either a Full or
Low Profile chassis.
Features and Benefits
• Conforms to PCI v2.2 Plug and Play
• Full support for Windows-based software
• Reduces CPU load and improves system
performance dramatically
• IRQ sharing feature reduces IRQ conflicts
• High-speed serial port (9-p
Краткое содержание страницы № 2
Package Contents • CyberPro PCI 2S board • 2-port fan-out cable • Low profile bracket (Dual Profile board only) • Driver CD • Quick installation guide Layout Full profile bracket* JP2 (Serial port 2) Fan-out cable connector (25-pin) JP1 (Serial port 1) Figure 1. Layout * Note: Depending on the model purchased, the bracket size will be either Full or Low profile. Jumper Settings (JP1, JP2) Open = 0 volts (default) Short 1-2 = 5V Short 2-3 = 12V Note: Most serial devices do not require additiona
Краткое содержание страницы № 3
Fan-out Cable 9-pin serial 25-pin connector 9-pin serial Figure 2. Fan-out cable Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds. Avoid any contact wit
Краткое содержание страницы № 4
5. Set JP1 and JP2 jumper settings to the desired voltage only if your serial device needs additional power from the serial port. However, most serial devices do not require additional power. For more information see Figure 1 on page 2. The jumpers can be removed if power is not required. 6. To install the card, carefully align the card's bus connector with the selected PCI slot on the motherboard. Push the board down firmly, but gently, until it is well seated. 7. Replace the slot bracket ho
Краткое содержание страницы № 5
Windows 98/98SE 1. At the Add New Hardware Wizard, click Next. 2. Select Search for the best driver for your device (Recommend), then click Next. 3. Insert the driver CD, check Specify a location, uncheck the other boxes, type in D:\9x, then click Next. (Change D: to match your CD-ROM drive letter) 4. Click Next, then Finish. 5. Repeat steps 1-4. 6. Restart Windows to complete the installation. Windows ME 1. At the Add New Hardware Wizard, select Specify the location of the driver (Advanced), t
Краткое содержание страницы № 6
3. Double click Multi-function adapters, SIIG CyberPro 2S PCI board and PCI Function should be displayed. Windows NT 4.0 1. From the desktop click Start, then Run. 2. Insert the driver CD, type in D:\NT4\Install_serial.exe, then click OK. (Change D: to match your CD-ROM drive letter) 3. Click Next when the Welcome window appears. 4. Select Install, then click Next. 5. Click Yes, then click Exit. 6. Restart Windows to complete the installation. To Verify Windows NT 4.0 Installation 1. Click Start
Краткое содержание страницы № 7
32-bit Windows XP/Server 2003 1. At the Found New Hardware Wizard, insert the driver CD. For XP w/SP1 or earlier/ Server 2003: go to step #2. For XP w/SP2 or later/Server 2003 wSP1 or later: select No, not this time, click Next. 2. Select Install the software automatically (Recommended, then click Next. 3. Click Finish. 4. Repeat steps 1-3 two more times. 5. Restart Windows to complete the installation. 64-bit Windows XP/Server 2003 1. At the Found New Hardware Wizard, insert the driver CD. For
Краткое содержание страницы № 8
To Verify Windows 2000/XP/Server 2003 Installation 1. Right click My Computer, click Manage, then click Device Manager. 2. Click on the + (plus sign) in front of Ports (COM & LPT), CyberSerial PCI 16Cxxx... should be displayed two times. 3. Double click Multifunction adapters, SIIG CyberPro 2S PCI board should be displayed. ™ Windows Vista 1. At the Found New Hardware window, insert the driver CD, click Locate and install driver software (recommended), then click Continue. 2. Click Next, then cl
Краткое содержание страницы № 9
Changing COM Port Address Some serial devices need a specific COM port in order to work. If your serial device works properly, do not change this setting. Windows 95/98/98SE/ME 1. From the Device Manager window double click Ports (COM & LPT), then double click the CyberSerial PCI serial port you want to change. 2. Click Settings tab, click the down arrow that is next to the Port Name box and select a COM address that is not currently in use. 3. Click OK, then close Device Manager to save the ch
Краткое содержание страницы № 10
Blank Page 10
Краткое содержание страницы № 11
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analysts will promptly respond. SIIG offers a lifetime manufacturer warranty with this product. Please see our web site for more warranty details. If you enco
Краткое содержание страницы № 12
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), networking, sound cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty. High-quality control standards are evident by
