Краткое содержание страницы № 1
PCA7427G02
PROM Programming Adapter for M37272E8/EFFP
User's Manual
Rev.1.00
September 1, 2003
REJ10J0248-0100Z
Краткое содержание страницы № 2
* IC51-0422-393 is a product of Yamaichi Electronics Co., Ltd. * R4945 and R4945A are trademarks of Advantest Corporation. Keep safety first in your circuit designs! • Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due considerat
Краткое содержание страницы № 3
Contents Chapter 1. Precautions for Safety ...........................................................................................4 1.1 Safety Symbols and Meanings ..............................................................................4 Chapter 2. Introduction ...........................................................................................................6 2.1 Things to Check When Unpacking .......................................................................6 Chapter 3.
Краткое содержание страницы № 4
Chapter 1. Precautions for Safety In both the user's manual and on the product itself, several icons are used to insure proper handling of this product and also to prevent injuries to you or other persons, or damage to your properties. This chapter describes the precautions which should be taken in order to use this product safely and properly. Be sure to read this chapter before using this product. 1.1 Safety Symbols and Meanings If the requirements shown in the "WARNING" sentences are ignored,
Краткое содержание страницы № 5
WARNING Warnings for Use Environment: • This equipment is to be used in an environment with a maximum ambient temperature of 35˚C. Care should be taken that this temperature is not exceeded. • Select the proper programming mode of the PROM programmer. CAUTION Caution to Be Taken for Modifying This Product: • Do not disassemble or modify this product. Disassembling or modifying this product can cause damage. Disassembling and modifying the product will void your warranty. Cautions to Be Taken for
Краткое содержание страницы № 6
Chapter 2. Introduction The PCA7427G02 is a PROM programming adapter for Renesas 7200 Series of 8-bit MCUs. The adapter is a tool that can be used to write programs into an internal PROM of MCUs using a commercially available PROM programmer. This manual describes the specifications and the operation of the PCA7427G02. Figure 2.1 shows the external view of the PCA7427G02 and its constituent parts. Figure 2.1 External view of the adapter and its constituent parts 2.1 Things to Check When Unpackin
Краткое содержание страницы № 7
Chapter 3. Specifications Table 3.1 lists specifications of the PCA7427G02. Table 3.1 Specifications of the PCA7427G02 Applicable MCUs M37272E8FP, M37272EFFP 1 MHz Operating clock frequency (Supplied by the ceramic oscillator mounted on the adapter) Power supply Supplied from Vcc of the PROM programmer IC socket IC51-0422-393 (made by Yamaichi Electronics Co., Ltd.) Board to insert a programmable MCU PCA7427G02 (IC socket mounted on it) Interface board (Connected by two rows of standard-pitch 18
Краткое содержание страницы № 8
Chapter 4. How to Write the Program This chapter describes procedures you need to follow when writing the program. For details on how to operate the PROM programmer, refer to the user's manual of the PROM programmer. 4.1 Programming Procedure Follow these procedures (1) through (8) to write the program into the MCU. (1) Read the program into the PROM programmer. (2) Attach the adapter to the IC socket of the PROM programmer. For details, see "4.2 Attaching the Adapter to a PROM Programmer" (page
Краткое содержание страницы № 9
4.2 Attaching the Adapter to a PROM Programmer As shown in Figure 4.1, attach the pin No. 1 of the PCA7402E connector (standard-pitch 32-pin pin- header mounted) to the pin No. 1 of the IC socket of the PROM programmer. Be careful when attaching the adapter because incorrect insertion can cause fatal damage to the MCU. Figure 4.1 Attaching the adapter to a PROM programmer 4.3 Setting the Jumper Switch Set the jumper switch SW1 according to the MCU type to be programmed. For setting, see Table 4.
Краткое содержание страницы № 10
4.4 Mounting an MCU into the Adapter (1) As shown in Figure 4.3, set the slide bar in the center of the IC socket to the shaded area on the board. (2) As shown in Figure 4.3, mount the MCU into the IC socket with the No. 1 pin of the MCU matched to the No. 1 pin of the IC socket on the PCA7427G02. Be careful when inserting the MCU because incorrect insertion can cause fatal damage to the MCU. Top view Figure 4.3 Mounting an MCU 4.5 Precautions When Opening and Closing the IC Socket When opening
Краткое содержание страницы № 11
4.6 Precautions When Handling the Adapter Do not touch the connector in the IC socket and the pins on the PROM programmer connector because dirt may cause an electrical insulation failure. When not using this product, attach the connector pins of this product to the conductive sponge as it was shipped from the factory. 4.7 Setting the Programming Areas When writing the program into the MCU, be sure to set the programming area. And also, specify its device of the PROM programmer. Table 4.2 Progra
Краткое содержание страницы № 12
Chapter 6. Memory Maps Figures 6.1 and 6.2 show memory maps of the MCUs (M37272E8FP and M37272EFFP) and the PROM programmer. 0000016 0000016 013FF16 013FF16 0140016 0140016 OSDROM OSDROM (10 KB) (10 KB) 03BFF16 03BFF16 03C0016 03C0016 07FFF16 07FFF16 0800016 0800016 Internal ROM area Programming area (32 KB) (32 KB) 0FFFF16 0FFFF16 Unused area 1FFFF16 MCU PROM programmer (M37272E8FP) (M5M27C101 mode) Figure 6.1 Memory map of the M37272E8FP ( 12 / 18 )
Краткое содержание страницы № 13
0000016 0000016 00FFF16 00FFF16 0100016 0100016 Internal ROM area Programming area (60 KB) (60 KB) 0FFFF16 0FFFF16 1000016 1000016 113FF16 113FF16 1140016 1140016 OSDROM OSDROM (10 KB) (10 KB) 13BFF16 13BFF16 13C0016 13C0016 1FFFF16 1FFFF16 MCU PROM programmer (M37272EFFP) (M5M27C101 mode) Figure 6.2 Memory map of the M37272EFFP ( 13 / 18 )
Краткое содержание страницы № 14
Chapter 7. Troubleshooting The table below summarizes errors to be checked carefully before you determine them to be a fault. 7.1 Errors That Occur When Writing to PROM 7.1.1 When Newly Purchased Cause Remedy See page Is the adapter attached to the correct position of the PROM 9 programmer? Programming adapter Is the MCU attached to the correct position? 10 Is the area specification set correctly? 11 PROM programmer Is the correct device selected? 11 The IC socket of the PROM programmer may be s
Краткое содержание страницы № 15
7.2 MCUs Do Not Function Normally The program operates normally on the emulator, but when the MCU that has normally been written is attached the same program does not function normally. (1) Is the offset address specified correctly when copying data into the PROM programmer? (2) In the emulator, NOPs are often inserted in the area where the program has not been read, therefore the program happens to appear functioning normally even though it may have gone wild. Check your program again. (3) The
Краткое содержание страницы № 16
MEMO ( 16 / 18 )
Краткое содержание страницы № 17
PCA7427G02 User's Manual Rev.1.00 September 1, 2003 REJ10J0248-0100Z COPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATION AND RENESAS SOLUTIONS CORPORATION ALL RIGHTS RESERVED
Краткое содержание страницы № 18
