Краткое содержание страницы № 1
••••••••••••••••••••••••••••••••••••••••
CTA 150i Installation Guide
Version française incluse.
Versión española incluída.
•••••••••••••••••••••••••
Краткое содержание страницы № 2
Краткое содержание страницы № 3
CTA 150i card installation 1 CTA 150i card installation Overview of this chapter This chapter provides instructions and information for installing and configuring the Norstar Computer Telephony Adapter 150i. The instructions in this chapter are designed for experienced PC users who are familiar with card installation. Installing the CTA 150i card in your PC Setting the address switch The CTA 150i card comes with the I/O port address switches preset as shown in Figure 1. This
Краткое содержание страницы № 4
2 CTA 150i card installation Table 1 CTA 150i card address settings Address switch setting I/O address 1 2 3 4 5 200 ON ON ON ON ON 210 ON ON ON ON OFF 220 ON ON ON OFF ON 230 ON ON ON OFF OFF 240 ON ON OFF ON ON 250 ON ON OFF ON OFF 260 ON ON OFF OFF ON 270 ON ON OFF OFF OFF 280 ON OFF ON ON ON 290 ON OFF ON ON OFF 2A0 ON OFF ON OFF ON 2B0 ON OFF ON OFF OFF 2C0 ON OFF OFF ON ON 2D0 ON OFF OFF ON OFF 2E0 ON OFF OFF OFF ON 2F0 ON OFF OFF OFF OFF 300 OFF ... OFF As in the 200s section above
Краткое содержание страницы № 5
CTA 150i card installation 3 Installing the CTA 150i card When you are ready to begin installing the card, power down the PC and unplug the PC’s power cord from the wall outlet. Make sure that you have the proper size screwdrivers for the task. To install the CTA 150i card: 1. Remove the outer cover from your PC. 2. Select an unused expansion slot. 3. Remove the cover of the selected expansion slot from the rear panel of the PC. Save the retaining screw. 4. If a plastic insert covers
Краткое содержание страницы № 6
4 CTA 150i card installation Connecting the CTA 150i card to Norstar The CTA 150i card does not need a dedicated Norstar phone line. It can share a phone line with one of the following Norstar phones: • M7100 • M7208 • M7310 (May be equipped with a busy lamp field) • M7324 (May be equipped with an attached Central Answering Position) In addition, the following requirements must be met: • The line cord that connects the phone to the CTA 150i card must be no longer than 15 m (50 ft). •
Краткое содержание страницы № 7
Preparing for installation 5 Preparing for installation Overview of this chapter This chapter provides an overview of the installation process described in later chapters in this guide. It also lists all the requirements that must be met before the Norstar TAPI SP can be installed. Overview of Norstar TAPI SP installation Installing the Norstar TAPI SP on your computer involves the following general steps: • verifying that your PC meets the system requirements listed in this chapte
Краткое содержание страницы № 8
6 Preparing for installation PC system requirements Before you install and configure the Norstar TAPI SP, you should become familiar with the system hardware and software requirements described in this section. Minimum hardware requirements The minimum hardware requirements for the Norstar TAPI SP include: • 486/33 MHz PC, EISA, or ISA bus • 3.5” disk drive • 450 Kbytes of free memory (RAM) • 820 Kbytes of free disk space for Norstar TAPI SP files (refer to your TAPI application
Краткое содержание страницы № 9
Preparing for installation 7 Norstar KSU requirements This section describes the components needed for the installation of the TAPI SP on Norstar Key Systems. Included are the necessary software releases, line cards, telephones, and interface devices supported. Required cabling is also listed. Software releases Table 2 lists the Key Systems supported by the Norstar TAPI SP. The CPC represents the product number on the software cartridge, and the Software code is the one that is d
Краткое содержание страницы № 10
8 Preparing for installation Norstar KSU configuration There are no specific configuration requirements to support TAPI applications on a Norstar KSU. Some configuration options commonly enabled by a CTI user for the “attached set” are: Handsfree/Headset: Useful when performing extensive PC-based directory dialing Offhook External Prime-Line: Allows a TAPI application to default dial internal or external calls Offhook Linepool Prime-Line: Allows a TAPI application t
Краткое содержание страницы № 11
Norstar TAPI SP installation 9 Norstar TAPI SP installation Norstar TAPI SP software installation This section describes the procedures that must be performed to install the Norstar TAPI SP. Pre-installation checklist Before installing the software, complete the following pre-installation checklist. 1. Verify that your PC meets the minimum hardware and software requirements. Verify that the interface device is connected and that the teleph
Краткое содержание страницы № 12
10 Norstar TAPI SP installation Installing Norstar TAPI SP software Ensure that the pre-installation checklist has been completed before you install the software. To install Norstar TAPI SP software: 1. Insert the Norstar TAPI SP disk (Disk 1) in the floppy disk drive. 2. Run setup.exe from the floppy disk using the following steps: a. (Windows 3.1) Select File from the Program Manager Menu bar. The File menu displays. (Windows 95) Select Start
Краткое содержание страницы № 13
Norstar TAPI SP installation 11 The TAPI SP files are installed in the Windows System directory. As the files are installed, progress indicators appear on your screen. Note: Under Windows 3.1, if the PC does not have Microsoft TAPI installed or has an earlier version of TAPI, the Norstar TAPI SP installer will install a new version of TAPI. When all the files have been installed, the Connection Hardware Properties dialog box appears. 5. Select the Device Type appropriate t
Краткое содержание страницы № 14
12 Norstar TAPI SP installation Port For an external interface device, select the serial port to which the device is connected on your PC. Base Address Select the address that matches the switch settings on your card or port. IRQ Select an available hardware interrupt number for your computer. For the CTA 150i card, valid values are in the range from 2 to 7, and 9. 7. Click OK when you have finished setting the properties for your interface device.
Краткое содержание страницы № 15
Norstar TAPI SP installation 13 2. Double-click on the Control Panel icon. The Control Panel window displays the Telephony icon. 3. Double-click on the Telephony icon. (Windows 3.1) The Telephony dialog box displays. Go to step 4. (Windows 95) The Telephony Properties dialog box displays. Go to step 5. 4. (Windows 3.1) Click Driver Setup. The Telephony Drivers dialog box displays. 5. Click on the Norstar Telephony SP entry to highlight it, and click
Краткое содержание страницы № 16
14 Norstar TAPI SP installation Figure 5 Connection Hardware Properties dialog box 7. If required, select the Device Type appropriate to the interface device you have installed on your PC. The following interface devices are supported in this release: • TelAdaptor • CTA 150i • CTA 500dm • CTA 100 • CTA 200 8. Select or change the appropriate properties for the interface device you selected. Refer to your vendor documentation for more information, if required. By clicking Defa
Краткое содержание страницы № 17
Norstar TAPI SP installation 15 9. Click OK when you have finished setting the properties for your interface device. The Norstar SP Configuration dialog box reappears. 10. Click OK on the Norstar SP Configuration dialog box when you have finished modifying the configuration. 11. Restart your PC so that the changes can take effect. Computer Telephony Adapter 150 Installation Guide
Краткое содержание страницы № 18
16 Norstar TAPI SP installation Computer Telephony Adapter 150 Installation Guide
Краткое содержание страницы № 19
•••••••••••••••••••••••••••••••••••••••• Guide d’installation de la carte CTA 150i •••••••••••••••••••••••••
Краткое содержание страницы № 20
