Краткое содержание страницы № 1
Краткое содержание страницы № 2
Caution The NetComm NP642 must be installed and operated in accordance with the instructions provided in this Quick Start Guide. Damage caused by incorrect or careless installation is not covered by warranty. Static Electricity Computers are very sensitive to static electricity which may be discharged by the user when the internal circuitry is touched. Ensure that you have discharged any static prior to touching the computer’s PCI slots and to removing the NetComm NP642 from its static ba
Краткое содержание страницы № 3
Contents INTRODUCTION ...................................................................................... 4 Wireless Terminology .......................................................................... 5 System Requirements ......................................................................... 7 GETTING TO KNOW YOUR NP642 ............................................................... 8 Package Contents ............................................................................... 8 NP6
Краткое содержание страницы № 4
INTRODUCTION Congratulations on your purchase of the NP642 108Mbps IEEE 802.11g Wireless PCI Card. This manual is designed to help familiarise users with the product and offers detailed operational and installation instructions, so please keep it for future reference. With the NP642 Wireless (IEEE 802.11g) PCI Card, a computer can communicate with the Network wirelessly. User-friendly utility software is bundled with the NP642 providing configuration, monitoring and diagnostic options. The N
Краткое содержание страницы № 5
Wireless Terminology Wireless Standards 802.11, 802.11b and 802.11g all refer to a series of standards which govern a common method of creating wireless local area networks (WLANs). 802.11b and 11g are the most common WLAN types, with 11g being the later and faster of the two standards with a maximum transmission rate of 54Mbps. The NP642 is faster again as it is built around a processor which ‘turbo-charges’ transmission rates up to 108Mbps. 802.11g is ‘backward compatible’ with 802.11b, wh
Краткое содержание страницы № 6
WPA WPA stands for Wi-Fi Protected Access - authorizes and identifies users based on a secret key that changes automatically at a pre-defined interval. This is called TKIP (Temporal Key Integrity Protocol) to change the temporal key every 10,000 packets (= unit of data.) Keys can either be pre-shared or established by a RADIUS Server. RADIUS RADIUS is part of 802.11i security; this is a wireless standard which is only concerned with wireless security standards. Authentication is based ar
Краткое содержание страницы № 7
System Requirements • Desktop computer with available 32bit PCI slot. • Windows 98SE, ME, 2000, XP • 32Mb of memory and a 300MHz processor • 20Mb spare disk storage • CD-ROM Drive Caution The NetComm NP642 must be installed and operated in accordance with the instructions provided in this Quick Start Guide. Damage caused by incorrect or careless installation is not covered by warranty. Static Electricity Computers are very sensitive to static electricity which may be discharged by the user
Краткое содержание страницы № 8
GETTING TO KNOW YOUR NP642 This chapter provides unpacking and setup information for the NP642 Wireless PCI Card. Package Contents Open the box of the Wireless PCI Card and carefully unpack it. The box should contain the following items: � One 108Mbps 802.11g Wireless PCI Card with removable antenna � One Installation CD, including Utility Software and User Guide. If any item is found missing or damaged, please contact your local reseller for replacement. 8 NP642 IEEE 802.11g PCI Adapter YM
Краткое содержание страницы № 9
NP642 LED Indicators LED Indicator Description Power (PWR) The PWR indicator lights green to indicate that it is receiving power from the PCI slot. If the PWR indicator light is off, it is not receiving power. ACT (Activity) The ACT indicator blinks green while the Wireless PCI Card is transmitting data. NP642 IEEE 802.11g PCI Adapter 9 YML785 Rev1
Краткое содержание страницы № 10
HARDWARE INSTALLATION PCI Card Installation Instructions 1. Shut down the computer, unplug the power cord, and remove the chassis cover. 2. Insert the contact edge of the Wireless PCI Card into the available PCI Bus Master Expansion slot. Press the card firmly into the connector so that the card’s contacts are fully seated in the PCI slot connector. 3. Install the bracket screw and secure the card to the computer chassis. 4. Replace the computer’s cover. 5. Switch the computer power on. Win
Краткое содержание страницы № 11
Connecting the Antenna Before continuing with the Software Installation section, you will need to connect the antenna 1. The antenna has a retaining nut which must be screwed into the connector on the back of the card. Place the screw retaining nut over the antenna connection on the rear of the NB642 and turn it clockwise. Screw retaining nut clockwise over the Bend antenna antenna connection o to a 90 angle Note: Do not over-tighten the attaching nut - but do make sure that you
Краткое содержание страницы № 12
SOFTWARE INSTALLATION This section will guide you through the driver and utility installation procedure for the NP642 Wireless PCI Card. Windows 98se/ME/2000/XP Utility and Driver Installation 1. Insert the Driver and Utility CD-ROM into the CD-ROM Drive. The driver and util- ity setup menu should start up and install the driver. Depending on your operating system, you may need to install the software manually. Go to your Windows start menu and select “Run”. Type “D:\Utility\Setup.exe” in th
Краткое содержание страницы № 13
Icon Description If the Icon is completely Green, you have excellent coverage and performance. If the icon is yellow, the signal strength has a fair coverage and performance. If the icon has no colour, signal strength is poor. NP642 IEEE 802.11g PCI Adapter 13 YML785 Rev1
Краткое содержание страницы № 14
USING THE WIRELESS UTILITY I. Link Information Launch the utility program by double clicking the utility icon in the Windows task bar. The following window is displayed after launching the Utility program. Field Description Status: Shows the BSSID (or Mac address) of the adaptor, which can be used to identify it on the wireless network. SSID: Shows current SSID, which must be the same for the all wireless devices in order for communication to be established. Frequency: Shows the current fre
Краткое содержание страницы № 15
Field Description Wireless Mode: Shows the current wireless mode used for wireless communication. Encryption: Shows the current encryption mode used in the wireless network. TxRate: Shows the current data rate used for transmitting. Channel: Shows the current communication channel. Link Quality: Shows the link quality of the NP642 Wireless PCI card with the Access Point when operating under Infrastructure mode. Signal Strength: Shows the strength of the wireless signal between the NP642
Краткое содержание страницы № 16
II. Configuration The configuration page enables you to set the basic parameters for your connection. Field Description SSID: Service Set Identifier, which is a unique name shared among all clients and nodes in a wireless network. The SSID must be identical for each client and node in the wireless network. Give your network a name which you will remember but which does not obviously identify it to the outside world. Wireless Mode: There are two types available for selection: ● Infrastructure
Краткое содержание страницы № 17
Field Description ● Ad-Hoc – to establish peer-to-peer wireless communication directly with other wireless client devices such as other computers with wireless cards. Ad-Hoc Band: There are three bands available for selection- 11B, 11G and 11G Turbo. Choice depends on the type of wireless equipment you wish to connect to. Check the documentation of the associated equipment to verify details. Channel: The channel value that the PCI card will operate in. Australian Users should select t
Краткое содержание страницы № 18
Field Description Preamble: Select Long Preamble or Short & Long Preamble type. Leave as default unless advised otherwise by your Network Administrator. Support Band: There are three functions for you to select, including 11B, 11G and eXtended Range. The default setting is 11B, 11G and eXtended Range enabled, which is interoperable with both 11B and 11G devices, and provides a connectivity range of 500m. Note: You must select at least 11B or 11G to support your wireless connection. 18 NP
Краткое содержание страницы № 19
III. Advanced In the Advanced page you can configure advanced settings for the NP642 wireless PCI Card Field Description Encryption: There are four options available: Disable (WEP), Enable (WEP), WPA and WPA-PSK. The default setting is set to “Disable”. Enable and Disable refer to WEP data encryption feature. If Enable is selected, you will be required to select the Authentication mode from the drop down list. If WPA is selected, configuration is enabled. Select the “configuration” button.
Краткое содержание страницы № 20
Select the certificate that you wish to use and enter the server name and login name; this refers to RADIUS Server technology which is generally not in use in the home environment; check with your Network Administrator if you are required to enter this in order to log on to a secure network. If WPA-PSK is selected, click the configuration button. You will then be prompted with the following pop up window. 20 NP642 IEEE 802.11g PCI Adapter YML785 Rev1
