Краткое содержание страницы № 1
User’s Manual
®
Cable Cubby 200
®
Cable Cubby 300C
®
Cable Cubby 300S
®
Cable Cubby 600
®
Cable Cubby 800
Surface Access Products for Cables, AAPs, and Power Outlets
Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan
1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Road, #04-01 Kyodo Building
68-701-01 Rev. F
Anaheim, CA 92805 3821 AH Amersfoort PM Industrial Building 16 Ichibancho
06 06
USA The Netherlands Singapore 368363 Chiyoda-ku, To
Краткое содержание страницы № 2
Краткое содержание страницы № 3
Table of Contents Chapter One � Introduction .................................................... 1-1 ® About the Cable Cubby Products ....................................... 1-2 Features ........................................................................................ 1-5 Chapter Two � Installation ...................................................... 2-1 Installation Overview ............................................................... 2-2 Preparing the Routing Template ...
Краткое содержание страницы № 4
Table of Contents, cont’d ® Cable Cubby Products Chapter One 1 Introduction ® About the Cable Cubby Products Features 68-701-01 Rev. F 06 06 All trademarks mentioned in this manual are the properties of their respective owners. ® ii Cable Cubby Products � Table of Contents
Краткое содержание страницы № 5
Introduction ® About the Cable Cubby Products The Extron Cable Cubbies are furniture-mounted, architectural solutions for inconspicuous cable access and connection points. When cables are not in use, they can be stored out of the way while remaining connected to the presentation system. Most US/domestic Cable Cubby models provide two unswitched USA AC power outlets. The US/domestic Cable Cubby 200 provides one outlet. Each of the international versions provides a single unswitched
Краткое содержание страницы № 6
Introduction, cont’d The installed Cable Cubbies fi t nearly fl ush within a table or Features podium top, storing the AAPs and cables out of the way and � Easy access to cables and AAPs out of sight. To access the AAPs and connectors, lift the lid � Durable mechanical movement (fi gure 1-2). Half-moon cutouts in the lid allow you to run cables in or out and then close the lid. For Cable Cubby 300s, � Cable Cubby 300, 600, and 800 available in a variety of 600s, and 800s, you can lower
Краткое содержание страницы № 7
Introduction, cont’d ® Cable Cubby Products Chapter Two 2 Installation Installation Overview Preparing the Routing Template Preparing the Table Installing the Cables and AAPs Mounting the Cable Cubby ® 1-6 Cable Cubby Products � Introduction
Краткое содержание страницы № 8
Width of Mounting Surface Installation Installation Overview Preparing the Routing Template Install and set up the Cable Cubby enclosures as follows: Extron provides metal templates for the Cable Cubbies at no charge. See Routing Template Part Numbers, in appendix A, 1 If you plan to use a mounting template that has not been Reference Information, for part numbers. Extron recommends prepared, prepare the template. See Preparing the Routing using this template as a guide to cut the hole
Краткое содержание страницы № 9
Installation, cont’d Wear safety glasses when operating the router. W Preparing the Table Failure to comply can result in eye injury. The preferred and recommended method for preparing the table for square Cable Cubbies and one of two preferred methods for 4. Using a router with a 5/8" (or 16 mm) outside diameter the Cable Cubby 300C is to use the appropriate Extron routing guide bushing and a 1/2" (or 12 mm or 12.7 mm) diameter template and a router. straight router bit, carefully cut th
Краткое содержание страницы № 10
Installation, cont’d Preparing the table with a hole saw Installing the Cables and AAPs (Cable Cubby 300C only) Each Cable Cubby 300, 600, and 800 model ships with one or two moveable AAP shelf assemblies. The Cable Cubby 200’s Prepare the table with a hole saw as follows: AAP shelf is fi xed in place. 1. On the tabletop or other installation surface, mark the 6" circle, then fi nd and mark the center of the circle. AAP shelf brackets (CC 300, 600, 800) Wear safety glasses when operating th
Краткое содержание страницы № 11
Installation, cont’d Install cables in the channels as follows: Installing the power module (CC 300, 600, 800) 1. Remove a segment of a set of split AAPs by unscrewing From the underside of the Cable Cubby, gently push the power the nuts on the underside of the bracket that fastens the module into the desired position at the desired elevation. Secure the power module into position with four Phillips head screws. plate to the shelf (CC 200) or shelf bracket (CC300, 600, or 800) (fi gure 2-4
Краткое содержание страницы № 12
Installation, cont’d 3. Install a second stand-off, in accordance with steps 1 and 2. Installing the shelf assembly (CC 300, 600, 800) 4. Slide the stand-offs back and forth in the horizontal slots to From the underside of the Cable Cubby, gently push the AAP position them so that the cables easily rise and lower but shelf assembly into the desired position at the desired elevation. Ensure there is enough space above the AAP assembly for the do not fall below the stand-offs. Cable Cubby li
Краткое содержание страницы № 13
Installation, cont’d 3. Carefully lower the Cable Cubby into the hole to test the 8. Cable Cubby 200 — Use the four included 6-32 x 1/2" fi t. If necessary, remove the enclosure and use a fi le or rasp screws to fasten the Cable Cubby 200 to the table to enlarge or smooth the edges of the opening (fi gure 2-7). (fi gure 2-8). 15-pin HD Cable Audio Cable Cable Cubby 300C Surface-Mountable RJ-45 Cable Enclosure for Cables, AAPs & AC Power Outlet Figure 2-8 — Cable Cubby, installation view Mounting
Краткое содержание страницы № 14
Installation, cont’d ® Cable Cubby Products Chapter 3 3 Maintenance and Modifi cations Removing and Replacing the Cable Cubby Replacing Cables or an AAP Adding an Additional Power Module (CC 600, CC 800) ® 2-14 Cable Cubby Products � Installation
Краткое содержание страницы № 15
Maintenance and Modifi cations The Cable Cubby can be modifi ed in the future to change cables, to replace an AAP, or to add a second power module. These modifi cation may require removing the cubby from the table. Removing and Replacing the Cable Cubby You may need to remove the cubby from the table in which it is mounted to replace cables or AAPs, to adjust the height of the AAP assemblies, or to install a second power module. Figure 3-1 shows removal of the Cable Cubby 300, 600, or 800
Краткое содержание страницы № 16
Maintenance and Modifi cations, cont’d 4. Cable Cubby 200 — Remove the screws at the four corners 10. Cable Cubby 300, 600, and 800 — Snugly tighten the that secure the cubby to the table (fi gure 3-2). Phillips head screws on the screw clamps to secure the enclosure to the surface. 11. Cable Cubby 300, 600, and 800 — Tighten the locking thumbscrews on the screw clamps to lock the clamp in position. 12. Cable Cubby 200 — Fasten the Cable Cubby 200 to the table with the four 6-32 x 1/2" screw
Краткое содержание страницы № 17
Maintenance and Modifi cations, cont’d Figure 3-4 shows typical confi gurations before and after Adding an Additional Power Module you add a second power module to an international (CC 600 and CC 800) Cable Cubby 800. Each additional power module occupies two (USA/domestic Before After models) or three (international models) of the cubby’s AAP spaces, reducing the amount of AAP space available in the cubby for cable pass through (split) or passive AAPs. Use the following guidelines as ap
Краткое содержание страницы № 18
Maintenance and Modifi cations, cont’d � Cable Cubby 600 and 800 US/Domestic models — Figure 3-6 shows typical confi gurations before and after You probably do need replacement shelf brackets you add a second US/Domestic power module to a when you add a US/Domestic power module to US/domestic Cable Cubby 800 and suggests rack shelf a US/Domestic Cable Cubby, because the power confi gurations to replace the lost shelf space. module takes up two spaces in a cubby that, in its Before After sta
Краткое содержание страницы № 19
Maintenance and Modifi cations, cont’d ® 4 Cable Cubby Products From the underside of the Cable Cubby, gently push the additional power module into the desired position at the desired elevation. Secure the power module into position with the included four Phillips head screws (fi gure 3-7). Extron Cable Cubby 600 2 Screws ea. side Appendix A A Figure 3-7 — Installing the power module 5 If desired, assemble and install replacement AAP shelf assemblies. Remember that the cable pull functio
Краткое содержание страницы № 20
Reference Information Specifi cations General d Rack mount .................................... No, but furniture mountable Enclosure type .............................. Metal H H Enclosure dimensions C Use the appropriate metal Extron routing template or refer to D D W W the surface cutout dimensions here before cutting a hole in the furniture or other surface. Pay special attention to the direction the unit will face; the unit’s AAP and connector access side Cable Cubby 300C Cable Cubby
