Краткое содержание страницы № 1
USB
10/100M
FAST ETHERNET
Installation Guide
M73-APO08-540
Краткое содержание страницы № 2
REGULATORY STATEMENTS FCC Certification Part15, Class B The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of electronic equipment. FCC Part 15 Registration This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interface, and 2. This device must accept any interface received, including interface that may cause un
Краткое содержание страницы № 3
INTRODUCTIONS The USB 10/100M Fast Ethernet Adapter provides outside-the-box plug-and-play local area network connections for USB-enabled PCs, notebooks and laptops. This adapter uses a B type USB port to connect with the USB host, and an RJ-45 port to connect with a 10/100 Fast Ethernet LAN link. Installation is easy and no external power is required! The network sharing is easier than ever. Specifications Network standard IEEE 802.3 for 10BaseT IEEE 802.3u for 100BaseTX Data Rate 1 10/100 M
Краткое содержание страницы № 4
Operation: 111mA (max) Sleep Mode: 3.9 mA (max) Parts Names and Functions USB Type A plug: connects the USB host port to the USB 10/100M Fast Ethernet Adapter. USB Fast Ethernet Adapter 10/ACT LED indicator: glows green when 10M Network is linked; blinks green when the Fast Ethernet Adapter is transmitting/ receiving data. 100/Act LED indicator: glows green when 100M Network is linked; blinks green when the Fast Ethernet Adapter is transmitting/ receiving data. Network Port: connects the
Краткое содержание страницы № 5
INSTALLATION Precaution Before the installation, make sure the USB port exists in your computer and is enabled. To check this, go to My Computer Control Panel System. Open the Device Manager tab. If the Universal Serial Bus controller device is found, it means your USB port is installed and enabled. If not, either no USB port is installed or the USB bios is not properly enabled. In this case, consult your computer dealer for USB support. Getting Hooked Up 1. Locate the USB host port of your sy
Краткое содержание страницы № 6
2. Connect the UTP cable to the Fast Ethernet Adapter. 3. Connect the other end to a Hub. - 4 -
Краткое содержание страницы № 7
SOFTWARE INSTALLATION Installation for Windows 98 1. Once the device is properly connected to your computer, Windows 98 will automatically detect the new hardware device. Perform the following procedures for installing the device driver. 2. Insert the device driver disk into your floppy drive. When the above figure appears, click Next. - 5 -
Краткое содержание страницы № 8
3. The installation program will proceed automatically. Follow the on-screen instruction to finish. 4. When Windows prompts you to restart your computer, click No to make some changes to your network settings. - 6 -
Краткое содержание страницы № 9
5. Go to Start Settings Control Panel. Double-click Network. 6. When the Network dialog box appears, select USB 10/100M Fast Ethernet and click Add. Set the appropriate protocols and client for you needs. When completed, click OK. 7. Remember to restart your computer to activate the new device Setup Diagnostics To verify if the device exists in your computer and is enabled, go to Start Settings Control Panel System. Click the Device Manager tab. If the 10/100 USB Network - 7 -
Краткое содержание страницы № 10
Adapter is found, it means that your device is properly installed and enabled. Installation for Windows 2000 1. Once the device is well connected to your computer, Windows 2000 will automatically detect the new device. Click Next to proceed. - 8 -
Краткое содержание страницы № 11
2. Select Search for a suitable driver for my device (recommended) and click Next. 3. Insert the new device driver to the disk drive. Select Floppy disk drives. Click Next. 4. Click Next. Windows will copy all the necessary files to your system. 5. Click Yes to continue. 6. Click Finish to complete the software installation. - 9 -
Краткое содержание страницы № 12
7. Go to Start Settings Control Panel Network and Dial-up Connections. Double-click Local Area Connections. 8. When the Network dialog box appears, select USB 10/100 Network Adapter and click Install. Set the appropriate protocols and client for you needs. When completed, click OK. - 10 -
Краткое содержание страницы № 13
9. Remember to restart your computer to activate the new device. Setup Diagnostics To verify if the device exists in your computer and is enabled, go to Start Settings Control Panel System Hardware. Click the Device Manager tab. If the USB 10/100 Network Adapter is found, it means that your device is properly installed and enabled. Installation for Windows ME 1. Once the device is well connected to your computer, Windows ME will automatically detect the new device. Select Specify the locat
Краткое содержание страницы № 14
3. Click Next to continue. 4. Click Next. Windows will copy all the necessary files to your system. - 12 -
Краткое содержание страницы № 15
5. Click Finish to complete the software installation. 6. When asked if you want to restart your computer, click No to continue the Network configuration. 7. Go to Start Settings Control Panel. Double-click Network. 8. When the Network dialog box appears, select USB 10/100 Network Adapter and - 13 -
Краткое содержание страницы № 16
click Add. Set the appropriate protocols and client for you needs. When completed, click OK. 9. Remember to restart your computer to activate the new device. Setup Diagnostics To verify if the device exists in your computer and is enabled, go to Start Settings Control Panel System. Click the Device Manager tab. If the USB 10/100 Network Adapter is found, it means that your device is properly installed and enabled. Installation for Windows XP 1. Once the device is well connected, Windows will
Краткое содержание страницы № 17
2. Insert the device Driver Disk into the floppy disk drive of your system. Select Search removable media (floppy, CD- ROM…) and click Next. 3. Click Next to continue. 4. Windows will start searching for the appropriate driver for the installation. When the screen appears as below, click Continue Anyway to proceed. - 15 -
Краткое содержание страницы № 18
5. Wait for seconds while Windows copies the appropriate driver to your system. 6. Click Finish. The software installation for this network device is now completed. 7. Go to Start Settings Control Panel Network and Dial-up Connections. Double-click Local Area Connections. - 16 -
Краткое содержание страницы № 19
8. When the Network dialog box appears, select USB 10/100 Network Adapter and click Install. Set the appropriate protocols and client for you needs. When completed, click OK. 9. Remember to restart your computer to activate the new device. Setup Diagnostics To verify if the device exists in your computer and is enabled, go to Start Control Panel System. Click the Device Manager tab. If the USB 10/100 Network Adapter is found, it means that your device is properly installed and enabled. - 17 -
Краткое содержание страницы № 20
- 18 -
