Краткое содержание страницы № 1
HP-PB 100VG-AnyLAN Network Adapter
Installation and Service
HP 3000 MPE/iX Computer Systems
Edition 1
B5426-90001
E0897
Printed in: U.S.A. August 1997
Краткое содержание страницы № 2
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability or fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for direct, indirect, special, incidental or consequential damages in connection with the furnishing or use of this material. Hewlett-Packard assumes no responsi
Краткое содержание страницы № 3
Contents HP-PB 100VG-AnyLAN Network Adapter Installation at a Glance 9 Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Product Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Tools and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 In This Book. . .
Краткое содержание страницы № 4
Contents Removal/Replacement Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Removal/Replacement of the Adapter . . . . . . . . . . . . . . . . . . . . . . . . . 28 Reshipment Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Gloss
Краткое содержание страницы № 5
Figures Figure 1-1 . Address Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Figure 1-2 . Inserting and Securing Adapter . . . . . . . . . . . . . . . . . . . . . .19 Figure 1-3 . Port Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Figure 2-1 . Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . .31 5
Краткое содержание страницы № 6
Figures 6
Краткое содержание страницы № 7
Tables Table 1-1. LED Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Table 2-1. Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Table 2-2. 100VG Network Adapter Technical Specifications. . . . . . . . .30 7
Краткое содержание страницы № 8
Tables 8
Краткое содержание страницы № 9
HP-PB 100VG-AnyLAN Network Adapter Installation at a Glance The following figure shows how to install the HP-PB 100VG-AnyLAN Network Adapter. 9
Краткое содержание страницы № 10
Installation Overview The installation procedure includes the following major steps: 1. Prepare to install the adapter. 2. Shut down the operating system and switch off the power to the computer. 3. Install the adapter. 4. Attach the adapter to the network. 5. Configure the adapter. 6. Verify operation. Product Description The HP-PB 100VG-AnyLAN Network Adapter provides the hardware needed to interface an HP-PB backplane to a 100VG-AnyLAN Network. The HP-PB 100VG-AnyLAN Network Adapter has the fo
Краткое содержание страницы № 11
In This Book This book is the installation and service manual for the HP-PB 100VG-AnyLAN Network Adapter that connects an HP 3000 computer using the HP-PB backplane to a 100VG-AnyLAN network. The installation procedure section contains the installation instructions. It explains in detail the steps necessary to install the adapter into your computer. The service information section defines the steps and procedures to follow if you experience trouble with the adapter. It explains diagnostics to be
Краткое содержание страницы № 12
12
Краткое содержание страницы № 13
1 Installation Procedure This section contains installation instructions for the HP-PB 100VG-AnyLAN Network Adapter. The instructions are organized into six primary steps listed below. Each step is described in detail in this section. If the adapter has already been installed at the factory, you may proceed directly to step 4. 1. Prepare to install the adapter. 2. Shut down the operating system and switch off the computer. 3. Install the adapter. 4. Attach the adapter to the network. 5. Configure
Краткое содержание страницы № 14
Installation Procedure 1. Prepare to Install the Adapter 1. Prepare to Install the Adapter Before installing the adapter, you should perform the following steps: 1. Observe antistatic precautions. 2. Verify product contents. 3. Record adapter identification information. 4. Gather tools and accessories. Observe Antistatic Precautions This product contains electronic components that can easily be damaged by small amounts of static electricity. To avoid damage, follow these guidelines: • Store adapt
Краткое содержание страницы № 15
Installation Procedure 1. Prepare to Install the Adapter Record Adapter Information Record the relevant information from the card here for future reference. If your adapter requires service in the future this information will be needed by HP service personnel. Card Information to Record Example Information Motherboard Model and Revision number __________________ H05000-003, REVB02 Daughter Card Model and Revision number __________________ H04522-001, REVC00 Daughter Card Serial number __________
Краткое содержание страницы № 16
Installation Procedure 1. Prepare to Install the Adapter Gather Tools and Accessories Check the hardware installation manual of your computer model for special tools and accessories required to access the I/O adapter slot(s). The following common tools are helpful: • screwdrivers necessary for opening your computer and installing adapters • grounding wrist strap NOTE You should have all of your system and peripheral device manuals available for reference. There may be special system or device de
Краткое содержание страницы № 17
Installation Procedure 2. Shut Down the Operating System and Switch Off the Computer 2. Shut Down the Operating System and Switch Off the Computer 1. Before installing the HP-PB 100VG-AnyLAN Network Adapter, ensure that the operating system is shut down. Refer to your computer system manuals for proper shutdown procedures to avoid corruption or loss of data. 2. Ensure that power to the host computer is switched off and disconnected from the source power supply. WARNING Unless otherwise noted in
Краткое содержание страницы № 18
Installation Procedure 3. Install the Adapter 3. Install the Adapter To install the adapter in the host computer, perform the following steps: a. Access the adapter slot(s). b. Select an available adapter slot. c. Insert the adapter into the slot. d. Switch on the power to the computer. a. Access the adapter slot(s) Because computer models vary, there may be different procedures to access and select an adapter slot. Before you install the adapter, you should refer to the manuals that apply to yo
Краткое содержание страницы № 19
Installation Procedure 3. Install the Adapter 2. Insert the adapter into the slot. Be sure the contacts and adapter guides are properly aligned. 3. Fold in the extractor levers. 4. Press the adapter firmly until you feel the connector mate fully. 5. Secure the adapter in its slot by securing the retaining screws. Figure 1-2 Inserting and Securing Adapter d. Switch on the power to the computer. 1. Reconnect the source power supply to the computer. 2. Switch on the computer power switch. Chapter 1
Краткое содержание страницы № 20
Installation Procedure 4. Attach the Adapter to the Network 4. Attach the Adapter to the Network Use the RJ-45 connector for connecting a UTP category 3 or 5 cable (not supplied) to a 100VG-AnyLAN hub or 10Base-T hub/switch. Refer to Figure 1-3.. Figure 1-3 Port Connection Attach the cable to the RJ-45 connector by following these steps: a. Plug the cable into the RJ-45 connector. b. Secure the other end of the cable to the 100VG-AnyLAN hub or 10Base-T hub/switch. c. If necessary, reconfigure the
