Краткое содержание страницы № 1
INSTALLATION INSTRUCTIONS
HB0061
UP27I and UP27E SERIES
! !
INTENDED FOR DOMESTIC COOKING ONLY
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
HOMEOWNER: USE AND CARE AND OPERATION INFORMATION ON
PAGES 13 AND 14.
®
In USA - BEST BY BROAN P.O. Box 140, Hartford, WI 53027
®
In Canada - BEST BY BROAN 550 Lemire Blvd., Drummondville, QC, J2C 7W9
REGISTER YOUR PRODUCT ON LINE AT: www.bestbybroan.com/register
For additional information - visit www.bestbybroan.com
V0785
Краткое содержание страницы № 2
! ! WARNING WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC TO REDUCE THE RISK OF INJURY TO PERSONS SHOCK OR INJURY TO PERSONS, OBSERVE IN THE EVENT OF A RANGE TOP GREASE THE FOLLOWING: FIRE, OBSERVE THE FOLLOWING*: 1. Use this unit only in the manner intended by the 1. SMOTHER FLAMES with a close-fitting lid, cookie manufacturer. If you have questions, contact the sheet or metal tray, then turn off the burner. manufacturer at the address or telephone number BE CAREFUL TO PREVENT BURNS. IF THE l
Краткое содержание страницы № 3
- UP27I SERIES RANGE HOOD SYSTEM - INTERIOR BLOWER Model 634 or 644 Model 647 Model 634 or 644 Model 643 (roof cap) (7” Round wall cap) (roof cap) (8” Round wall cap) Model 418 Model 415 8” round Model 459 (7” round adjustable transition adjustable elbow, 3¼” x 14” elbow, (optional) to 8” round optional) Model 407 8” round Model 412 (7” round duct standard transition 2 ft. sections) duct 3¼” x 14” 3¼” x 10” rectangular to 7” round standard duct 3¼” x 10” rectangular standard duct Model 459 t
Краткое содержание страницы № 4
- UP27E SERIES RANGE HOOD SYSTEM - IN-LINE AND EXTERIOR BLOWERS Model 441 Model 437 Model ILB9 (800 cfm) (10” Round wall cap) (High capacity roof cap) Model EB12 (1200 cfm) or ILB11 (1100 cfm) or EB15 (1500 cfm) in-line blower exterior blower Model EB6 (600 cfm) (includes two 8” x 12” to or EB9(900 cfm) 10’’ round transitions) exterior blower Model 441 (10” Round wall cap) Model ILB6 (600 cfm) in-line blower (includes two 4½” x 18½” to 10’’ round transitions) Model 421 Model 418 (10” Round ver
Краткое содержание страницы № 5
1. SELECT BLOWER OPTION AND INSTALLATION TYPE 1.1 NON-DUCTED INSTALLATION (ONLY FOR UP27I SERIES HOODS) The non-duct kit ANKUP Series (sold separately) must be installed. This kit fits hood from 30-inch width up to 48-inch width. See installation instructions included with the non-duct kit ANKUP Series. 1.2 DUCTED INSTALLATION Either UP27I or UP27E Series range hoods may be ducted. For a UP27E Series range hood, either an exterior blower or in-line blower may be used. The Best by Broan UP27E S
Краткое содержание страницы № 6
2. PREPARE THE INSTALLATION CAUTION When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves. Remove the installation kit from inside the hood. Make sure that the following items are included: - Installation manual - Adapter/damper 3¼” x 14” to 3¼” x 10” (exclusively for UP27I Series range hoods, temporarily assembled to pan, behind Evolutionary™ hybrid baffle filters) - Adapter/damper 3¼” x 14” (exclusively for UP27I Series range hood
Краткое содержание страницы № 7
5. REMOVE THE GREASE DRIP RAIL Remove tape on grease drip rail. Lift out grease drip rail and set aside. HD0212 6. REMOVE THE PAN Using a Phillips no. 2 screwdriver, remove the screws retaining the pan (shaded parts on illustration below) to the hood. Remove the pan and set aside. NOTE: There are 2 screw models for UP27I pan retaining screws; the flat end type (A) (n°. 8 x 3/8”) are shorter and located near the front of the hood and the pointed end ones (B) (n°. 6 x 1/2”) are longer located in
Краткое содержание страницы № 8
7. PREPARE THE CABINET (CONT’D) 7.1 DUCTED INSTALLATION: 36”, 42” OR 48” INTERNAL BLOWER HOOD 30” INTERNAL BLOWER HOOD Cut-out the openings for CABINET BOTTOM CABINET BOTTOM duct (A) and house wiring (120 V AC)(B) according to the direction C C L L of discharge chosen. See figures beside. 13” A 14” A NOTE: For all UP27I Series B (internal blower) Ø 1¼” B 3¾” 3¾” range hoods, the 2” ¾” cut-out opening for 7¼” 7¼” 7¼” 7¼” 2” house wiring (120 V AC) ½” ½” can be made in cabinet 30” INTERNAL
Краткое содержание страницы № 9
8. PREPARE THE HOOD (CONT’D) 8.1 UP27I SERIES RANGE HOOD (INTERNAL BLOWER) (CONT’D) VERTICAL DISCHARGE (CONT’D) Using 4 no. 8 x 3/8” screws provided with hood, secure the chosen adapter/damper to the top of the hood. Remove tape from damper flap. HD0201 Seal the adapter/damper to the hood using duct tape. HD0202 HORIZONTAL DISCHARGE (DUCTED INSTALLATION ONLY) The UP27I Series range hoods are factory set to exhaust vertically. If the horizontal discharge is chosen, remove the metal shut-off pl
Краткое содержание страницы № 10
8. PREPARE THE HOOD (CONT’D) 8.1 UP27I SERIES RANGE HOOD (INTERNAL BLOWER) (CONT’D) HORIZONTAL DISCHARGE (DUCTED INSTALLATION ONLY)(CONT’D) TOP OF HOOD Using 3 no. 8 x 3/8” screws provided with hood, secure the adapter/damper on the back of the hood. Remove tape from damper flap. ADAPTER/DAMPER SCREW LOCATION BACK OF HOOD HD0204 Seal the adapter/damper and the metal shut-off plate to the hood using duct tape. HD0205 8.2 UP27E SERIES RANGE HOOD (EXTERIOR OR IN-LINE BLOWER) WIRING COVER Run hou
Краткое содержание страницы № 11
10.INSTALL THE HOOD Place the hood at its location. Using a pen, mark the position of the screw (smaller part of the keyholes [A]). Remove the hood and install (4) 1/2” double thread screws at marked positions, leaving a 1/8” gap. Place the hood under the cabinet and slide it in position. Make sure the adapter/damper enters the ducting and the damper opens freely (UP27I Series range hood only), or ensure ducting connects to rough-in plate (UP27E Series range hood only). Secure the hood by tighte
Краткое содержание страницы № 12
13.REINSTALL GREASE DRIP RAIL AND BAFFLE FILTERS Reinstall the grease drip rail. HD0214 CAUTION Remove protective plastic film covering Evolutionary™ hybrid baffle filters before installing them. 13.1 DUCTED INSTALLATION: Reinstall Evolutionary™ hybrid baffle filters on the hood. 13.2 NON-DUCTED INSTALLATION: Slide out and discard the secondary micromesh filters from the back of the baffle filters. Slide in the charcoal filters included in the non-duct kit. Reinstall the baffle filters on the h
Краткое содержание страницы № 13
15.USE AND CARE Evolutionary™ Hybrid Baffle Filters The Evolutionary™ hybrid baffle filters should be cleaned frequently. Use a warm detergent solution. Wash more often if your cooking style generates greater grease—like frying foods or wok cooking. Remove Evolutionary™ hybrid baffle filters by pushing them towards the front of hood and rotating filters downward. Slide out the secondary micromesh filter from the back of each hybrid baffle filter before cleaning. Baffle filters are dishwasher saf
Краткое содержание страницы № 14
16.OPERATION (CONT’D) HEAT SENTRY Both UP27I and UP27E series are equipped with a HEAT SENTRY thermostat. If blower is ON at a lower speed setting and excessive heat is detected above the cooking surface, it turns the blower up to HIGH speed. When the temperature level drops to normal, the blower will return to its original setting. If blower is OFF and excessive heat is detected above the cooking surface, HEAT SENTRY will turn the blower to HIGH speed. When the temperature level drops to
Краткое содержание страницы № 15
SERVICE PARTS UP27I MODEL 2 1 23 22 4 5 6 3 10 21 7 20 8 11 12 19 13 16 18 9 15 14 17 HL0088 KEY PART QTY (HOOD WIDTH) NO. NUMBER DESCRIPTION 30’’ 36’’ 42’’ 48 1 V14971 ADAPTER/DAMPER 3¼” X 14” 1 1 1 1 2 T461 ADAPTER/DAMPER 3¼” X 14” TO 3¼” X 10” 1 1 1 1 3 V03435 THERMISTOR HEAT SENTRY 11 11 4 V07834 ROTARY CONTROL 22 22 5 V07689 TOGGLE SWITCH 22 22 6 V16966 PLASTIC CONTROL FRAME AND KNOB ASS’Y 11 11 7 V07688 KNOB 22 22 8 V16569 LAMP SHELL, SOCKET AND TRIM ASS’Y 22 44 9 V05921 HALOGEN BULBS (50
Краткое содержание страницы № 16
SERVICE PARTS UP27E MODEL 6 5 7 1 8 2 3 4 14 9 13 10 12 11 HL0089 KEY PART QTY (HOOD WIDTH) NO. NUMBER DESCRIPTION 30’’ 36’’ 42’’ 48’’ 1 V13923 FEMALE CONNECTOR 11 11 2 V13924 MALE CONNECTOR 11 11 3 V03435 THERMISTOR HEAT SENTRY 11 11 4 V07688 KNOB 22 22 5 V16966 PLASTIC CONTROL FRAME AND KNOB ASS’Y 11 11 6 V07689 TOGGLE SWITCH 22 22 7 V07834 ROTARY CONTROL 22 22 8 V16569 LAMP SHELL, SOCKET AND TRIM ASS’Y 22 44 9 V05921 HALOGEN BULBS (50 W, 120 V, PAR16, GU-10) 2 2 4 4 V08070 SECONDARY MICROMESH
