Краткое содержание страницы № 1
ROTARY MOWER
L59KR17-1
For use on Kubota L175 & L225 tractors
equipped with SFL-22 ROPS
Tested. Proven. Unbeatable.
51642
Rev. 11/9/2007
OPERATOR'S MANUAL
Краткое содержание страницы № 2
TO THE DEALER: ® Assembly and proper installation of this product is the responsibility of the Woods dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Product Registration included with the Operator’s Manual. The customer must sign the registration which certifies that all Dealer Check List items have been complete
Краткое содержание страницы № 3
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . .
Краткое содержание страницы № 4
SPECIFICATIONS Cutting Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60" Cutting Height Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5" - 5" Blade Speed (RPM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,410 Blade Tip Speed (feet per minute). . . . . . . . . . . . . . . . . . . . . . 12,778 Blade Spindles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Number of Blades . . . . . . .
Краткое содержание страницы № 5
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Make sure all safety decals are installed. Safety is a primary concern in the design and Replace if damaged. (See Safety Decals section for manufacture of our products. Unfortunately, our location.) efforts to provide safe equipment can be wiped Make sure shields and guards are properly out by an operator’s single careless act. installed and in good condition. Replace if dam- In addition to the design and configuration of aged. equ
Краткое содержание страницы № 6
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Do not operate equipment while under the influ- Do not operate or transport equipment while ence of alcohol or drugs. under the influence of alcohol or drugs. Operate only in daylight or good artificial light. MAINTENANCE Keep hands, feet, hair, and clothing away from Before performing any service or maintenance, equipment while engine is running. Stay clear of all lower mower to ground or block securely, turn off moving parts.
Краткое содержание страницы № 7
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! and system pressure is released by operating Tighten all bolts, nuts and screws to torque valve levers. chart specifications. Check that all cotter pins are installed securely to ensure equipment is in a safe Wear gloves when installing belt. Be careful to condition before putting unit into service. prevent fingers from being caught between belt Make sure all safety decals are installed. and pulley. Replace if damaged. (See Safety
Краткое содержание страницы № 8
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 2 - PN 18877 WARNING TO AVOID SERIOUS INJURY OR DEATH: Read Operator's Manual (available from dealer) and follow all safety precautions. Keep all shields in place and in good condition. Operate mower from tractor seat only. Lower mower, stop engine and remove key before dismounting tractor. Allow no children or untrained persons to operate equipment. Do not transport
Краткое содержание страницы № 9
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! BE CAREFUL! 6 - PN 23376 Use a clean, damp cloth to clean safety decals. Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off. Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator
Краткое содержание страницы № 10
OPERATION The designed and tested safety of this machine NOTICE depends on it being operated within the limitations as ■ Tractor upper stop of hydraulic control lever explained in this manual. Be familiar with and follow all must be set to prevent any part of mower from safety rules in the manual, on the mower and on the coming closer than 1/4" to the tractor or mower lift tractor. bracket when mower is in the fully raised position. The safe operation of this mower is the responsibility of the
Краткое содержание страницы № 11
end high will produce ragged cuts with a scalloped Without Optional Casters look, excessive shredding, and will require extra power. With lift height set and mower leveled, lower mower to Attitude will be adjusted with the rear end low when desired cutting height and set lower lift control stop. using the leaf mulcher. See instructions on page 27 for This allows the mower to be raised when necessary, attitude adjustment. then lowered back to a pre-set cutting height. With Optional Casters PRE-OP
Краткое содержание страницы № 12
Should mower become plugged, causing belt to slip for ground speed will range from two to five miles per hour. over two seconds, raise mower just enough to clear Tall, dense grass should be mowed at low speeds, plug and continue running for at least two minutes, while thin, medium-height grass can be cut at a faster allowing pulleys to cool. Stopping the mower with belt ground speed. in contact with a very hot pulley will bake and ruin belt. Always operate PTO at 1000 rpm when mowing. This To re
Краткое содержание страницы № 13
NOTICE ■ On extremely uneven terrain, rear wheel weights should be used to improve traction. The addition of rear tractor weight or liquid ballast in rear tires will increase tractor stability. Pass diagonally through sharp dips and avoid sharp drops to prevent hanging up the tractor and mower. Practice will improve your skills in maneuvering rough terrain. Avoid sudden starts and stops when traveling up or down hill. Always mow down steep slopes--never up or across the face. Slow down on sharp
Краткое содержание страницы № 14
OPTIONAL EQUIPMENT Casters Casters are used to adjust and maintain cutting height. Front Roller Make sure attachment is properly secured, adjusted, and in good operating condition. Make sure shields and guards are properly installed and in good condition. Replace if damaged. ■ Before working underneath, raise mower to highest position and block securely. Blocking up Figure 4. Scalping Without Front Roller prevents mower dropping from hydraulic leak down, hydraulic system failures, or mechani
Краткое содержание страницы № 15
Four holes for mounting the front roller are provided in Leaf Mulcher Installation (Figure 8) front center. Mount the left and right roller brackets in Place mower upside down on saw horses or other sup- these holes. ports. Remove side shields (13), but do not remove Hole patterns determine right and left brackets. The left side skids. roller bracket should be installed with the highest hole to the rear and bracket angle extending left. Remove front roller if installed. The right bracket should
Краткое содержание страницы № 16
1. Spacer 2. Leaf mulcher 3. 3/8" Nut 4. 3/8" Lock washer 5. 3/8" Flat washer 6. Baffle bracket 7. Center baffle 9. 3/8" Lock nut 10. 3/8" x 1" Bolt 11. Angle lug 12. 3/8 x 1-1/8" Bolt 13. Side shield Figure 8. Optional Leaf Mulcher Installation 51642 (Rev. 11/9/2007) 16 Optional Equipment
Краткое содержание страницы № 17
OWNER SERVICE The information in this section is written for operators who possess basic mechanical skills. Should you need help, your dealer has trained service technicians avail- able. For your protection, read and follow all safety information in this manual. Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts. Figure 9. Spindle Lubrication Caster Lubrication (Figure 10) Before performing any service or maintenance, Lubricate cas
Краткое содержание страницы № 18
Frequently check blades. They should be sharp, free of nicks and cracks, and securely fastened. Remove mower from tractor and locate for easy access to bottom and top of mower. Secure to prevent mower from falling. Inspect blades before each use to determine that they are tight and in good condition. Replace any blade that is bent, excessively nicked, worn, or has any other damage. Small nicks can be ground out when sharpen- ing. Blade Removal (Figure 11) Wedge a block of wood between blade and
Краткое содержание страницы № 19
DEALER SERVICE The information in this section is written for dealer ser- Removal vice personnel. The repair described herein requires Remove blade from spindle. special skills and tools. If your shop is not properly equipped or your mechanics are not properly trained in Remove belt from pulleys. this type of repair, you may be time and money ahead Disassemble split taper bushing (located on top of pul- to replace complete assemblies. ley) by removing the two bolts and inserting them into the th
Краткое содержание страницы № 20
of seal. A tubing with an OD that is too small will bow Blade Spindle Assembly (Figure 13) seal cage. Bearing cones and cups are designed to work together. Carefully press seal into housing, preventing distortion It is important to position them so bearing cone taper to metal seal cage. Seal should seat firmly and mates with cup taper. squarely against machined shoulder in housing. Lubricate new cups with a light oil. Place them in spin- Make sure seal lip did not roll under. Distortion to seal
