Краткое содержание страницы № 1
swisherinc.com
OWNER’S
MANUAL
MODEL NO.
ZT2350
STARTING SERIAL # L505-353001
“ “ “ “Z Z Z Z” ” ” ” S S S SE E E ER R R RI I I IE E E ES S S S
Z ZE ER RO O T TU UR RN N H HY YD DR RO OS ST TA AT TI IC C D DR RI IV VE E
Z ZE ER RO O T TU UR RN N H HY YD DR RO OS ST TA AT TI IC C D DR RI IV VE E
IMPORTANT
Read and follow all
Safety Precautions
and Instructions
Assembly
before operating this
equipment. Operation
Service and Adjustment
Rev. 05-353
Repair Parts
1602 CORPORATE DRIVE, P.O
Краткое содержание страницы № 2
LIMITED WARRANTY The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of two (2) years from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship. This warranty is subject to the following limitations and exclusions: 1) Engine Warranty All engines utilized on our products have a
Краткое содержание страницы № 3
Thank you for choosing Swisher’s Zero Turn Rider Mower. Before operating your mower, please read, understand and follow all of the safety precautions and other instructions explained in this manual . As with all power equipment, lawnmowers can be potentially dangerous if improperly used. SAFETY PRECAUTIONS & DECALS This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of pers
Краткое содержание страницы № 4
The operation of any cutter can encounter foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles for over spectacles before starting any cutting machine and while operating such a machine. The operation of any cutter produces sound waves that are damaging to the human ear. Ear protection is recommended. CAUTION! Tragic accidents can occur if the operator is not alert to the presence of children. Child
Краткое содержание страницы № 5
• Turn off the blades when not mowing. Before leaving the machine, turn off the blades and stop the engine. • Watch for traffic when operating near or crossing roadways. • Do not operate the mower if it has been dropped or damaged in any manner or if the mower vibrates excessively. Excessive vibration is an indication of damage. Repair mower as necessary. • Dress properly. Do not operate the mower when barefoot or wearing open sandals. Wear only solid shoes with good traction when mowing.
Краткое содержание страницы № 6
Danger/Warning Decal – OD99155 Ignition/PTO/Throttle Decal – OD99154 Ignition/PTO/Throttle Decal 50” Mower Only – OD99157 Notice Do Not Alter Wiring Decal– OD74 Swisher Flag U.S.A.– OD39 Triangle Danger Decal – OD55 Operator Must Be Seated Decal– OD73 Parking Brake Decal – OD99152 Flying Debris Decal – OD43 No Step Decal – OD11 DECALS NOT SHOWN 50" Deck White Decal - OD99160 Z 23.0/50" Decal – Front - 11843 Height of Cut Decal - OD99153 Z 23.0/50" Decal – Right - 11845 Height Indicator Decal - O
Краткое содержание страницы № 7
UNCRATING/ASSEMBLY • Dispose of top and side panels of the crate. • Remove loose parts and packing material. • Cut any banding or strapping that may be holding the mower to the crate. • Disengage spark plug wire and place where it cannot make a connection. • Assemble the seat and clip wiring harness into the bottom of seat. NOTICE: Mower will not start unless the seat is connected to the wiring harness. • Raise mower deck to its highest position by turning the handle clockwise. • Set parking bra
Краткое содержание страницы № 8
MOWING WARNING: Do not operate mower at too fast of a rate. Sudden movements forward and backward at fast speeds can cause accidents resulting in personal injury. • Start out moving steering levers SLOWLY forward and backward until you learn to operate the unit. NOTE: This mower has been designed to be very maneuverable. Practice in open, flat areas is extremely necessary to become comfortable and efficient with the controls. • BEGIN TO MOW: Before starting the engine, set the desired deck he
Краткое содержание страницы № 9
MAINTENANCE SCHEDULE INSPECT BEFORE EACH USE • Loose fasteners: Be sure all fasteners are at proper torque. Especially guards and blades. • Parking brake: If brake does not keep unit from rolling, brake must be adjusted or repaired. • Tires: Always check and maintain proper tire pressure (See tire sidewall for recommendation). Check for damage due to sharp rocks, objects or stumps. • Operator Presence System: The engine should not start unless the PTO switch is disengaged and the control
Краткое содержание страницы № 10
INSPECT EVERY 25 HOURS • Lubrication: Grease all pivot points with a high temp grease. • Battery, check and clean: Keep battery terminals clean and tight. Periodic charging will extend its life. Clean terminals with a wire brush and coat with a petroleum jelly. • Change engine oil and filter: Use only quality detergent oil. See engine manual for instructions. Select viscosity grade according to your expected environmental temperature. • Blades: Best results will come from sharp blades. Re
Краткое содержание страницы № 11
SERVICE / ADJUSTMENTS CAUTION: Before performing any service or adjustments do as follows: 1. Turn off PTO switch. 2. Position unit on smooth flat surface. 3. Place steering levers in outward, neutral-locked position. 4. Turn ignition key “OFF” and set parking brake. 5. Wait for all moving parts to stop and disconnect spark plug wire. TRACKING Adjustments to the unit may need to be made if the unit does not track in a straight line. The primary reason for the unit not tracking s
Краткое содержание страницы № 12
REMOVING THE MOWER DECK 1. Turn off engine and engage parking brake. 2. Rotate cutting height lever counterclockwise to lowest cutting position. 3. Remove bolt from pickup point located at the front of the deck. 4. Remove cotter pins on rear hanger points and slide out stabilizer bars.Disconnect tension spring bolt from tension bracket. 5. Remove belt from mower pulley and electric clutch. 6. Slide mower deck from under unit. INSTALLING THE MOWER DECK 1. Be sure the cutting height lever is in
Краткое содержание страницы № 13
LEVELING THE MOWER DECK 1. Position unit on a smooth level surface. 2. For side to side leveling, measure the distance from the floor to the bottom edge at the rear of the deck. The measurement should be equal within 1/16 inch side to side. Adjustment can be made by loosening locking nut on rear eyebolt hangers and adjusting up or down as needed. 3. For front to rear pitch adjustment, loosen locking nut on front eyebolt and adjust up or down as needed. Proper pitch measurement is 1/8” t
Краткое содержание страницы № 14
BELTS Clutch drive belt replacement 1. Remove belt covers. 2. Disconnect tension idler from tension bracket. 50” 3. Remove belt from mower pulley and electric clutch. 4. Install new belt onto electric clutch and mower pulley and check for proper routing Part #: 3816 and clearance. 5. Reconnect idler tension bolt to tension bracket. Hydrostats belt replacement 1. Remove clutch drive belt. See clutch belt replacement. 2. Disconnect wiring from electric clutch. 3. Disconnect idler spring from te
Краткое содержание страницы № 15
WIRING DIAGRAM 50” Mower 15
Краткое содержание страницы № 16
ENGINE SETUP Item # Description Part # 1 23 HP B&S Engine (50" Mower) N/A 2 5/16-18 Serrated Flange Nut NB170 3 Spacer Engine Pulley BB105SL 4 Motor Pulley 3" 3753 5 1/4 X 1/2 Key Stock 4258 6 Engine Pulley Spacer Short .687 689S 7 Electric Clutch Drop Pulley 688ECDP Electric Clutch (50" Mower Only) 3813 8 Washer Belleville Engine Pulley 699 9 7/16-20 X 3.25 HCF GR5 ZP NB705 10 5/16-18 X 1 1/4 Serrated Flange Bolt NB253 11 Oil Drain Valve AS122 12 Oil Drain Valve Cap AS123 FUEL SUPPLY SYSTEM It
Краткое содержание страницы № 17
Item # Description Part # Note: Spring #2 must pivot freely on 1 Wire Link For Idler Arm BRS6H bolt #4 to prevent pre-mature failure. 2 Clutch Rod Spring 682S 3 5/16-18 Serrated Flange Nut NB170 4 5/16-18 X 1 HCC GR5 ZP NB501 3715 – TRANSMISSION 5 Transmission Idler Arm 3690TK IDLER DETAIL 6 1/2-13 X 3 HCC GR5 Bolt ZP NB131 7 3/8-16 X 1 1/2 HCC GR5 ZP NB107 8 3/8 SAE Washer NB272 9 Idler Pulley B27 10 3/8-16 2-Way Lock Nut NB280 11 1/2-13 Jam Nut NB118 12 5/16-18 Nyloc Nut NB181 13 Hydro Relea
Краткое содержание страницы № 18
STEERING (RIGHT SIDE SHOWN) Item # Description Part # Item # Description Part # 1 Directional Handle Grip 3673 18 5/16-24 ZP 2-Way Lock Nut NB448 2 Right Handle-Weldment 3839TK 19 1/4-20 X 1 1/4 HTC GR5 ZP NB103 Left Handle-Weldment 3846TK 20 Universal Pivot Plate Weldment 3698TK 3 5/16-18 X 3/4 Serr Flg Bolt NB596 21 Control Card Right 3621TK 4 5/16-18 Serrated Flange Nut NB170 Control Card Left 3620TK 5 1/2 NR Mach Bushing 14 GA NB177 22 Tinnerman Clips 5/16-18 Heavy Duty 3669 6 1/2 ID X 7/8 O
Краткое содержание страницы № 19
SEAT BASE ASSEMBLY Item # Description Part # 1 Seat 18" Back With Arm Rest 3792 2 Seat Plate 3133TK 3 5/16-18 Shoulder Bolt NB743 4 Seat Bracket 3833TK 5 5/16-18 Nyloc Nut NB181 6 Tinnerman Clip 5/16-18 3706 7 5/16-18 X 3/4 Serr Flg Bolt NB596 8 5/16 ID X 1 1/4 OD 11GA Black Nylon Washer NB116 9 5/16-18 Jam Nut NB173 10 T Knob 5/16-18 3844 11 Control Cover 3393TK 12 Brake Linkage Rod 3390Z 13 Seat Mount 3613TK 14 5/16-18 Serrated Flange Nut NB170 15 5/16 USS Flat Washer ZP NB556 16 Tapered Sprin
Краткое содержание страницы № 20
PARKING BRAKE Item # Description Part # 1 Brake Mount Plate 3267TK 2 1/8 X 1 Cotter Pin NB126 3 Brake Linkage Rod 3390Z 4 5/16-18 Nyloc Nut NB181 5 5/16-18 ZP 2 Way Lock Nut NB558 6 5/16 USS Flat Washer ZP NB556 7 5/16-18 X 1 Eye Bolt NB202 8 5/16-18 Serrated Flange Nut NB170 9 Spring (2 speed) T2SM 10 Parking Brake Weldment 3797TK 11 T Knob 5/16-18 3844 12 5/16-18 Jam Nut NB173 13 5/16 11GA Black Nylon Washer NB116 14 1/4-28 X 3/4 GR5 ZP NB620 15 1/4 Split Lock Washer NB135 16 5/16 X 1 1/4 OD F
