Краткое содержание страницы № 1
Safety Instructions & Operator’s Manual for
EUROPEAN
REAR ENGINE RIDING MOWER
SERIES 18
MODELS
E281318BE
E331518KVE
MODEL NUMBER EXPLANATION
E 28 10 18 K V E
EUROPEAN MODEL ENGINE OPTIONS
CUTTING WIDTH ENGINE TYPE
ENGINE HP ENGINE MODEL
SERIES DESIGNATION
E - European Model 28 - 28” Cutting Deck 13 - 13.0 HP Engine 18 - Series Designation B - Briggs Engine V – Over Head Valve
33 - 33” Cutting Deck 15 - 15.0 HP Engine K - Kohler Engine E - E
Краткое содержание страницы № 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind
Краткое содержание страницы № 3
IMPORTANT SAFETY INSTRUCTIONS PREPARATION OPERATION (Continued From Previous Page) (Continued From Previous Column) 7. Keep people and pets out of mowing area. 14. Exercise CAUTION when pulling loads. Limit Immediately STOP blades, STOP engine, and loads to those you can safely control and attach STOP machine if anyone enters the area. loads to hitch plate as specified with SNAPPER 8. Check shields, deflectors, switches, blade attachment instructions. controls and other safety devic
Краткое содержание страницы № 4
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS.......................................................... 2-3 TABLE OF CONTENTS...................................................................................... 4 SECTION 1 - FAMILIARIZATION .................................................................... 5-7 Decals / Symbols.........................................................................................................6-7 SECTION 2 - OPERATING INSTRUCTIONS.................
Краткое содержание страницы № 5
Section 1 - FAMILIARIZATION STEERING FUEL VENT FUEL TANK WHEEL FILLER CAP REAR BUMPER OPERATOR’S SEAT CONTROL PANEL TRANSMISSION (See Inset) SHIFT LEVER CLUTCH/BRAKE PEDAL DECK LIFT LEVER DISCHARGE DEFLECTOR MOWER DECK MOWER DRIVE CONTROL PANEL BELT BLADE PEDALS IGNITION SWITCH BLADE LEVER ENGINE SPEED CONTROL PARK BRAKE LEVER FIGURE 1.1 1.1 INTRODUCTION 1.2 NO
Краткое содержание страницы № 6
Section 1 – FAMILIARIZATION – DECALS / SYMBOLS SERIAL NUMBER DECAL 01015 PATENT NUMBERS DECAL - 2-9470 EUROPEAN NOISE CONTROL DECAL 23009 EUROPEAN COMMUNITY DECAL 29776 FUEL CAUTION DECAL - 29113 WARNING DECAL 22841 BATTERY STORAGE DECAL - 29948 CHUTE WARNING DECAL 29784 DEFLECTOR CAUTION DECAL 29839 BATTERY CAUTION DECAL - 29947 LOWEST HEIGHT OF CUT
Краткое содержание страницы № 7
Section 1 – FAMILIARIZATION – DECALS / SYMBOLS BLADE ENGAGED POSITION SAFETY INSTRUCTION DECAL - 35974 BLADE LEVER POSITION SYMBOLS BLADE DISENGAGED POSITION ENGINE SPEED CONTROL SYMBOLS CHOKE POSITION FAST TRANSMISSION SHIFT LEVER SYMBOLS RABBIT MACHINE FRONT “FAST” PARKING BRAKE SLOW SYMBOL E ENGINE N SPEED NEUTRAL G CONTROL I CLUTCH/BRAKE, N PARKING BRAKE, BLADE OPERATION
Краткое содержание страницы № 8
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST 2.2 OPERATOR’S SEAT ADJUSTMENT Make the following checks and perform the service 2.2.1. FRONT TO REAR ADJUSTMENT required before each start-up. 1. With the engine stopped, loosen the two adjusting 2.1.1. Check tires and add or release air as needed knobs and move seat to desired position. After to bring pressure to 12 psi in front and 12 psi in rear adjustment, tighten knobs securely. If seat does not tires. move after loo
Краткое содержание страницы № 9
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION TO APPLY 2.3.1. ENGINE (ELECTRIC START) BRAKES, PUSH CLUTCH/BRAKE IMPORTANT: When the ignition key is turned to PEDAL ALL THE “START”, the engine will turn over, but will not start WAY DOWN unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the “Off” position (See Figure 2.5).The operator should be in the seat. Start engine as follows: 1. Move transmission shift lever to (N) Neutral positio
Краткое содержание страницы № 10
Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 5. Move engine speed control to the choke position 2.3.1. ENGINE (ELECTRIC START) (Continued) to start a cold engine. See Figure 2.7. 8. Should the battery be too weak to start the engine, 6. Turn key to “RUN” position. See Figure 2.9. Refer to Section “ENGINE (MANUAL START)” to manually start the electric start engines. 2.3.2. ENGINE (MANUAL START) IMPORTANT: When the ignition key is turned to “RUN”, and the recoil handl
Краткое содержание страницы № 11
Section 2 - OPERATING INSTRUCTIONS WARNING WARNING Once blade is disengaged, it should come to a DO NOT operate blades in reverse. STOP BLADES. complete stop in 3 seconds or less. If the blade LOOK and SEE behind and down for children, pets continues to rotate after 3 seconds, the blade brake and hazards before and while backing. must be adjusted. Refer to Section “BLADE BRAKE ADJUSTMENT” for adjustment procedures or return machine to an authorized SNAPPER dealer for adjustment.
Краткое содержание страницы № 12
Section 2 - OPERATING INSTRUCTIONS TO APPLY WARNING BRAKES, PUSH DO NOT leave machine with the engine running. CLUTCH/BRAKE Stop engine. Stop blade. Shift to neutral. Engage PEDAL ALL THE parking brake. Remove key. WAY DOWN 2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.4.1. ENGINE 1. Stop engine by turning key to the “OFF” position. See Figure 2.13. FIGURE 2.14 BLADE LEVER IN “OFF” POSITION KEY RELEASE BLADE PEDALS FIGURE 2.13 2.4.2. WHEEL DRIVE 1. Stop mo
Краткое содержание страницы № 13
Section 2 - OPERATING INSTRUCTIONS 2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.5. CUTTING HEIGHT ADJUSTMENT 2.4.4. PARK BRAKE 1. Adjust cutting height as desired to any one of six 1. Engage park brake by pushing clutch/brake pedal positions using deck lift lever. When in desired height of cut, release latch, then try to move deck “DOWN” and moving the park brake lever to the “ON” lift lever to ensure lift lever latch is fully engaged. position. While holding the park brake lever “ON”,
Краткое содержание страницы № 14
Section 3 - MAINTENANCE 5. After all the oil has drained, close the drain and WARNING wipe up any oil that may have spilled. See Figure 3.1. DO NOT attempt any adjustments, maintenance, Dispose of used oil properly. service or repairs with the engine running. STOP 6. Fill engine crankcase with new oil. Refer to your engine. STOP blade. Engage parking brake. Remove engine owner’s manual for oil specifications. key. Remove spark plug wire from spark plug and 7. Change oil filter on
Краткое содержание страницы № 15
Section 3 - MAINTENANCE 28”, 30”, & 33” MODELS WARNING (Dual Idler System) DO NOT attempt any adjustments, maintenance, ENGINE DRIVE service or repairs with the engine running. STOP SPINDLE PULLEY engine. STOP blade. Engage parking brake. Remove PULLEY ASSEMBLY key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and vent must be closed secur
Краткое содержание страницы № 16
Section 3 - MAINTENANCE 3.2.8. LUBRICATION – GREASE FITTINGS The following components on the Rear Engine IMPORTANT: If the Rear Engine Rider will be on its Rider are equipped with grease fittings and rear bumper for longer than two hours, remove the require periodic lubrication. Apply General battery. Refer to Section “BATTERY REMOVAL”. Purpose grease (NLGI No.2) with a grease gun. 1. Front Wheel Bearings. Refer to Section 3.3.6. MOWER DECK LINKAGE - LUBRICATION “FRONT WHEEL BEARING
Краткое содержание страницы № 17
Section 3 - MAINTENANCE DIFFERENTIAL CASE 3.3 SERVICE - EVERY 25 OPERATING HOURS 3.3.8. REAR AXLE BEARING - LUBRICATION 1. The left rear axle bearing on 28” and 30” machines requires three shots of general purpose grease from grease gun. See Figure 3.7. NOTE: Some models are equipped with a pre- lubricated sealed bearing and require no additional lubrication. FILL/LEVEL PLUG P.N. 1-1024 2. The right rear axle bearing is lubricated by the differential lubricant and requires no
Краткое содержание страницы № 18
SECTION 3 – MAINTENANCE 3.4 SERVICE - ANNUALLY WARNING 3.4.1. Perform all maintenance as specified in DO NOT attempt any adjustments, maintenance, service “MAINTENANCE SCHEDULE” Section of this manual. or repairs with the engine running. Stop engine. Stop 3.4.2. FUEL FILTER blade. Engage parking brake. Remove key. Remove Service fuel filter as instructed below, on COLD spark plug wire from spark plug and secure away from ENGINE ONLY! plug. Engine and components are HOT. Avoid ser
Краткое содержание страницы № 19
Section 4 - ADJUSTMENTS & REPAIR WARNING WARNING DO NOT attempt any adjustments, maintenance, DO NOT operate machine until blade brake is service or repairs with the engine running. Stop adjusted and functioning properly. If blade stop time engine. Stop blade. Engage parking brake. Remove can not be achieved with the adjustment procedure key. Remove spark plug wire from spark plug and described above, take machine immediately to an secure away from plug. Engine and components are au
Краткое содержание страницы № 20
Section 4 - ADJUSTMENTS & REPAIR 9. Readjust rear hanger chain pivots to align with WARNING holes in support brackets. DO NOT attempt any adjustments, maintenance, See Figure 4.4. service or repairs with the engine running. STOP 10. Remove angle iron, pipe, or similar object and engine. STOP blade. Engage parking brake. Remove proceed to check front to rear levelness. key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are 4.2.3. MOWER DECK A
