Краткое содержание страницы № 1
INSTALLATION AND OPERATION INSTRUCTIONS
SINGLE KEG BEER DISPENSER
MODEL NOS.
DP32S
DS32S
Table of Contents
PREPARING THE CABINET FOR USE
Specifications.........................................................2
List of Included Parts.............................................3
Tools Required.......................................................3
IMPORTANT INFORMATION
Plumbing................................................................3
A Warranty card is enclosed that must be filled out
El
Краткое содержание страницы № 2
Installation and Operating Instructions Sizes and Specifications, Single Keg Beer Dispensers MODEL NUMBERS DP32S DS32S CABINET STYLE Portable Underbar HALF BARREL CAPACITY 1 Keg 1 Keg AMPS 2.7 2.7 SHIP WT lbs. (kg) 222 (101) 216 (98) INTERIOR Door Pan & Ceiling: High strength polystyrene. Door Sill: High strength polyethylene. Floor Pan: Stainless steel. Walls: Galvanized steel. Stainless steel top, back, sides and front. Galvanized bottom. Condensing unit grille EXTERIOR stainless steel. Deco
Краткое содержание страницы № 3
Preparing the Cabinet for Use – Single Keg Beer Dispensers Parts List Installing Casters (Portable Models Only) Casters* . Attach four casters to the cabinet bottom; rigid Faucet Standard. casters at the rear and swivel casters on the front. 1 3 Use the supplied / 4”- 20 x / 4” hex head self- Faucet Head Assembly. tapping machine screws. Spanner Wrench for Faucet. 3 Black Connector Hose ⁄16” x 3’. Placing the Cabinet 5 ⁄16” Air Hose. Push the cabinet into place using rollers when
Краткое содержание страницы № 4
Installation and Tapping – Single Keg Beer Dispensers Connecting the Keg Coupler Connecting the Regulator to the (when Supplied by Perlick) CO2 Cylinder Place one brown leather washer into black beer Remove blue plug from regulator fitting. line connector hose on hex nut side. Screw (Note: Do not remove the carbonic washer). connector to stainless steel beverage line on Screw regulator onto gas cylinder valve. Tighten faucet standard. Tighten with a wrench, but do with wrench until verti
Краткое содержание страницы № 5
Installation and Tapping – Single Keg Beer Dispensers or dirt before attaching regulator. CO2 Leak Test Store CO2 cylinder and regulator assembly Dilute a small amount of liquid dishwashing soap upright. and rub the soapy mixture around each connection. Allow only properly trained and experienced If bubbles appear, tighten connection. personnel to handle high pressure gas. NEVER... Replacing CO2 Gas Cylinder Connect cylinder directly to a keg without a regulator (reducing valve). Tur
Краткое содержание страницы № 6
Draft Beer Information – Single Keg Beer Dispensers Temperature One of the most common causes of dispensing At temperatures lower than 30° F., beer will freeze. When beer freezes, the alcohol in the beer may problems is improper temperature. Draft beer separate and cause the beer to be cloudy with an should be stored at a temperature between 32° and 38°. At warmer temperatures, beer will foam. “off” taste. Draft beer is not pasteurized and must be kept cool at all times. Refrigeration and Tempe
Краткое содержание страницы № 7
Cleaning the Beer System – Single Keg Beer Dispensers The entire beer system, to include the faucet, flexible Beer Stone: beer line and tapping devices must be cleaned at All beer contains calcium which is present from regular intervals. We recommend flushing the entire the grains used in the brewing process. it is an system with fresh water immediately after a keg has important natural material in draft systems in been emptied. Once each month the system should that as it oxidizes it coat
Краткое содержание страницы № 8
Pouring a Perfect Glass of Beer – Single Keg Beer Dispensers ➠ STEP 1 Start with a clean glass. Place the glass at a 45° angle, one inch below faucet. Do not let the glass touch the faucet. Open the faucet all the way. STEP 2 ➠ After the glass has reached half full, gradually bring the glass to the upright position ➠ STEP 3 Let the remaining beer run straight down the middle of the glass. This ensures proper release of CO2 by 3 producing a ⁄4” to 1” foam head. STEP 4 ➠ Close the faucet quickly
Краткое содержание страницы № 9
Trouble Shooting – Single Keg Beer Dispensers Beer Service Problems Cloudy Beer: Beer in glass appears hazy, not clear. Wild Beer: CAUSES: Dispensed beer has either too much foam or Dirty glass. is all foam. Dirty faucet or beer line. CAUSES: Frozen or nearly frozen beer. Beer has been dispensed improperly. Old beer. Solution: See pouring instructions Beer that has not been refrigerated for a on page 8. long period of time. Regulator pressure is set too high. Warm keg tempe
Краткое содержание страницы № 10
Replacement Parts – Single Keg Beer Dispensers MODEL NOS. DP32S & DS32S Item Description Part #’s 1 Compressor for R134a 63778 2 Condenser fan motor 63807 3 Condenser fan motor bracket 65166-1 4 Condenser fan blade 63808 5 Side panel 66215-1SS 6 Front grille 66210-8SS 7 Condenser 65528 8 Evaporator fan blade - 4” 63461 9 Evaporator fan motor C15239A 10 Evaporator assembly - complete 66295 11 Top assembly 66230-32T 12 Temperature control 61271 13 Door assembly 66256-1 14 Magnetic door gasket
Краткое содержание страницы № 11
Replacement Parts – Single Keg Beer Dispensers For Single Valve Keg Coupler (Series D) 14 4 Item Part 3 No. No. Description 1 .............32499................Probe assembly 1 2 ............F40184...............Probe body 2 3...........31080-2P.............Ball 4............43641-1 ..............Ball retainer 5...........31087-2P.............Probe washer 15 6 .............31089................“O” Ring - 3-per assembly 13 6 7 .............43061................Body 8...........23682-2P..........
Краткое содержание страницы № 12
Wiring Diagram – Single Keg Beer Dispensers EVAPORATOR FAN BLACK WHITE THERMOSTAT BLACK JUNCTION POINTS CONDENSER FAN WHITE COMPRESSOR BLACK WHITE POWER CONNECTION GREEN RED OVERLOAD NEMA–15P CORD RELAY WHITE END VIEW 8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069 Toll Free 800-558-5592 • E-Mail: Perlick@Perlick.com • www.Perlick.com Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without p
