Краткое содержание страницы № 1
IMI CORNELIUS REMCOR INC g 500 REGENCY DRIVE g GLENDALE HEIGHTS, IL 60139--2268
Telephone (800) 551--4423 Facsimile (800) 519--4423
Operator ’ s Manual
ICE/BEVERAGE DISPENSER
Model: Enduro-150 8 Valve
IMPORTANT:
TO THE INSTALLER.
It is the responsibility of
the Installer to ensure that
the water supply to the
dispensing equipment is
provided with protection
against backflow by an air
gap as defined in
ANSI/ASME A112.1.2-1979;
or an approved vacuum
breaker or other such
method as proved effective
Краткое содержание страницы № 2
TABLE OF CONTENTS Page MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 DAILY (OR AS REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 WEEKLY (OR AS REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 MONTHLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Краткое содержание страницы № 3
MAINTENANCE The following dispenser maintenance should be performed at the intervals indicated: DAILY (or as required) Remove foreign material from vending area drip tray to prevent drain blockage. WEEKLY (or as required) Clean vending area. Check for proper water drainage from the vending area drip tray. MONTHLY Clean and sanitize the hopper interior and beverage system, if applicable (see CLEANING INSTRUCTIONS). START-UP & OPERATING INSTRUCTIONS Fill the hopper with ice. Dispense several large
Краткое содержание страницы № 4
C. Wash cup rest with soap solution and rinse in clean water. Install the cup rest into the drip tray. D. Clean all exterior surfaces with soap solution and rinse in clean water. 2. CLEANING INTERIOR SURFACES CAUTION: When pouring liquid into the hopper, do not exceed the rate of 1/2 gallon per minute. Important: Perform the following at least once a month. A. Remove agitator assembly. B. Using a nylon bristle brush or sponge, clean the interior of the hopper, top cover and agitator assembly wit
Краткое содержание страницы № 5
E. Using a cloth, wash down the surfaces of the cold plate and plastic cover with soap solution. F. Install and properly position the cover on the cold plate. G. Install the splash panel in the reverse order it was removed. H. Rinse cold plate surface by pouring potable water through hopper openings. 2. DISPENSING VALVES Refer to addendum supplied with the unit that is applicable to the manufacturer of the valves installed on the unit. 3. PRODUCT TUBING Only trained and qualified persons should
Краткое содержание страницы № 6
c. Submerge all disconnects (gas and liquid) in the soap solution and then clean them using a nylon bristle brush. (Do not use a wire brush). Rinse with clean water. d. Using a plastic pail, prepare approximately five (5) gallons of sanitizing solution. e. Rinse the B-I-B disconnects in the sanitizing solution. f. Sanitizing fittings must be attached to each B-I-B disconnect. If these fittings are not available, the fittings from empty B-I-B bags can be cut from the bags and used. These fittings
Краткое содержание страницы № 7
TROUBLESHOOTING IMPORTANT: Only qualified personnel should service internal components or electrical wiring. WARNING: If repairs are to be made to a product system, remove quick disconnects from the applicable product tank, then relieve the system pressure before proceeding. If repairs are to be made to the CO system, stop dispensing, shut off the CO supply, then relieve the 2 2 system pressure before proceeding. If repairs are to be made to the refrigeration system, make sure electrical power i
Краткое содержание страницы № 8
Trouble Probable Cause BEVERAGES NOT SWEET ENOUGH. A. Empty syrup tank. B. Faucet brix requires adjusting. BEVERAGES NOT COLD (UNITS WITH BUILT-IN A. Unit standing with no ice in hopper -- no ice in COLD PLATE). cold plate cabinet. Contact your local syrup or beverage equipment distributor for additional information and troubleshoot- ing of beverage system. 6 620904402
Краткое содержание страницы № 9
PARTS LIST / EXPLODED VIEW 7 620904402
Краткое содержание страницы № 10
19 52 57 5 87 96 1 26 68 32 63 80 2 46 94 79 66 69 4 56 44 74 39 90 50 48 91 92 74 62 81 49 30 21 94 64 25 67 51 6 72 24 61 10 54 72 88 60 73 74 72 72 17 58 71 76 75 53 88 7 22 12 76 93 84 34 88 86 70 15 77 13 95 14 72 59 47 8 85 55 23 83 16 620904402 8
Краткое содержание страницы № 11
CABINET SECTION PARTS LIST Index No. Part No. Name 1 21491 Gate Slide 2 22081R Gate Restrictor 3 Not Used 4 **29303R Plate, Motor Mounting 5 15346 Agitator Assy 6 620021201 Cover, Rear Wrapper 7 629080213 Lower Panel Assy (For Drip Tray) 629080215 Lower Panel Assy (Z Model) 8 620020101 Sink Extension Assy, Drip Tray 9 Not Used 10 620020001 Wrapper 11 Not Used 12 Contact Sales Panel Cold Plate/Faucet Assy 13 27107 Retainer Lever, Ice Dispenser 14 10145 Pin Sink Ext. 15 31007 Switch Boot 16 50335
Краткое содержание страницы № 12
CABINET SECTION PARTS LIST (CONT’ D) 35 Not Used 36 Not Used 37 Not Used 38 Not Used 39 620019701 Hinge, Gusset 40 Not Used 41 Not Used 42 Not Used 43 Not Used 44 **51859 Seal, Agitator Motor Shaft 45 Not Used 46 51891 Gasket, Gate 47 ***51908 Plug (120V Models Only) 48 **52876 Gasket, Motor Shaft 49 620500901 Ice Chute 50 53168 Ice Chute Cover 51 53241 Access Cover (Cold Plate Models Only) 52 53227 Agitator Disk 53 Contact Sales Merchandiser, Black Contact Sales Merchandiser, Gray 620024118 Mer
Краткое содержание страницы № 13
CABINET SECTION PARTS LIST (CONT’ D) 68 70067 Washer, .218 I.D. 69 70076 Hex Nut, No. 8-32 70 70104 Nutsert No. 8-32 71 Contact Sales Graphics 72 70171 Machine Screw, Phil Truss Hd, No. 8-32 By 3/8-In. Long 73 70178 Machine Screw, Phil Truss Hd, No. 8-32 By 1/2-In. Long 74 70204 Sheet Metal Screw, Phil Truss Hd, No. 8 By 1/2-In. Long 75 620503401 Spacer, Cabinet 76 51334 Adhesive Tape 77 15500 Dispense Lever, Short (Cup Activated) 15488 Dispense Lever, Long (Cup Activated) 15501 Push Lever (Ice
Краткое содержание страницы № 14
5 4 11 17 7 N N C C O L O 2M 1 13 NO L1 NC COM 15 16 2 9 12 18 14 10 FRONT RIGHT SIDE FIGURE 2. ELECTRICAL BOX ASSEMBLY EXPLODED VIEW ELECTRICAL BOX ASSEMBLY Item No. Part No. Name 1 620019001 Electrical Box 2 620019101 Reflector Panel 3 Not Used 4 30514 Clamp, Capacitor, 120 Volt 620308102 Clamp, Capacitor, 220-240 Volt 5 30774 Capacitor, 120 Volt 620308101 Capacitor, 220-240 Volt 6 Not Used 7 31107 Terminal Board 8 Not Used 9 31620 Starter 10 31621 Ballast, 120 Volt 33662 Ballast, 220-240 Volt
Краткое содержание страницы № 15
SOLENOID ASSEMBLY 9 11 4 5 14 3 6 15 5 12 13 10 8 7 1 2 FIGURE 3. SOLENOID ASSEMBLY Item No. Part No. Name 1 28173 Arm, Gate Lift 2 50754 Bearing, Gate Arm 3 32957 Solenoid, 120 Volt 33397 Solenoid, 220-240 Volt 4 28172 Plate, Solenoid Mounting 5 50752 Isolator 6 70015 Hex Nut, No. 10-32 7 51689 Locktite 8 70162 Screw, No. 8-32 By 1/4-In. Long 9 50705 Tie Cable 10 70165 Screw, No. 8-32 By 5/8-In. Long 11 71007 Spring, Solenoid Arm 12 51348 Spacer 13 70067 Washer, .218 I.D. By .875 O.D. 14 70057
Краткое содержание страницы № 16
DRAIN TO COLD PLATE DRAIN ELBOW 1 3 4 1 TO COLD PLATE DRAIN ELBOW 1 1 2 1 3 FIGURE 4. COLD PLATE DRAIN FOR Z STYLE UNITS Item No. Part No. Name 1 70750 Hose Clamp 2 53170 Drain Tube 3 51280 Elbow 4 53293 Coupler 620904402 14
Краткое содержание страницы № 17
IMI CORNELIUS INC. ONE CORNELIUS PLACE ANOKA, MN. 55303--6234 TELEPHONE (800) 238--3600 FACSIMILE (612) 422--3232 WARRANTY IMI Cornelius Inc. and Remcor Products Company warrant that all equipment and parts are free from defects in material and workmanship under normal use and service. For a copy of the warranty applicable to your Cornelius and or Remcor product, in your country, please write, fax or telephone the IMI Cornelius office near- est you. Please provide the equipment model number and
Краткое содержание страницы № 18
IMI CORNELIUS INC. Corporate Headquarters: One Cornelius Place Anoka, Minnesota 55303-6234 (612) 421-6120 (800) 238-3600
