Краткое содержание страницы № 1
Otreap Or ’s Mlauna
Triple Rear Bagger — 19A40002100
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
Form No. 769-04626C
(February 24, 2010)
Краткое содержание страницы № 2
To The Owner 1 Thank You Thank you for purchasing a bagging attachment manufactured If you have any problems or questions concerning this by Cub Cadet. It was carefully engineered to provide excellent equipment, phone your local Cub Cadet dealer or contact us performance when properly operated and maintained. directly. Cub Cadet’s Customer Support telephone numbers, website address and mailing address can be found on this page. Please read this entire manual prior to operating the equipmen
Краткое содержание страницы № 3
Important Safe Operation Practices 2 WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol. HEED ITS WARNING! DANGER! This attachment was built to be used according to the safe operation practices in
Краткое содержание страницы № 4
3. Use slow speed. Choose a low enough speed setting so General Service that you will not have to stop or shift while on the slope. 1. Before cleaning, repairing, or inspecting, make certain the Tires may lose traction on slopes even though the brakes blade(s) and all moving parts have stopped. Disconnect the are functioning properly. Always keep machine in gear spark plug wire and ground against the engine to prevent when going down slopes to take advantage of engine unintended starting
Краткое содержание страницы № 5
Fold along dotted line (represents a 10° slope) Sight and hold this level with a vertical tree... or a corner of a building... or a fence post 10° Use this page as a guide to determine slopes where you may safely operate your mower with a grass bag attachment installed. WARNING! Do not operate your lawn mower with a bagger attachment on inclines with a slope in excess of 10 degrees (a rise of approximately 1-3⁄4 feet every 10 feet). A riding mower with a bagger attachment could overturn and c
Краткое содержание страницы № 6
Contents of Carton 3 Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below and shown in Fig. 3-1. Three hardware packs are included in this kit and are detailed on the following page. • Hinge Cover Pin • Hitch Bracket Kit (3 Pcs. & Hardware Pack) • Bagging Blades (6 blades total) • Chute Tube Extension • Two Deck Baffles • Discharge Chute Elbow • Chute Discharge Plate • Hitch Support • Chute Stop Bracket • Grass Catc
Краткое содержание страницы № 7
CONTENTS OF HARDWARE PACK This grass collector kit is shipped with three loose hardware packs enclosed and one set of hardware included in the mounting bracket kit. Please check your hardware packs against the illustrations below. The quantities for each item is listed in parenthesis. Hardware included with 689-00096 Hardware Pack 689-00163 (3) (1) (1) 712-04065 710-3008 (3) 710-0276 (2) 712-04064 712-04063 (2) Hardware Pack 689-00087 (1) 726-3046 (4) (3) 710-3008 711-0309A (4) 710-3015 (1) 71
Краткое содержание страницы № 8
Assembly & Installation 3 NOTE: References to left, right, front and rear of the tractor are from the operator’s position, unless otherwise stated. • Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop the tractor engine and set the parking brake. • For convenience, pivot the seat forward and leave it in that position until the grass collector is fully mounted and assembled. Assemble Mounting Brackets To assemble the bagger mounting assembly, locate the mou
Краткое содержание страницы № 9
Note: The clevis pin can be fed down through the hitch plate and secured underneath with the hairpin clip, or it may be easier to feed the clevis pin up through the hitch plate hole and secure with the hairpin clip on the topside. The latter method may be preferred since it can be easier to insert the hairpin clip. Either way will work, the decision should be based on operator preference. Figure 4-4 Align hole on bracket Mount Assembly on Tractor with hole on tractor Install mounting asse
Краткое содержание страницы № 10
Assembling Remaining Bagger Components Now that the mounting brackets are assembled and are in place on the tractor, follow these steps to assemble the remaining bagger components. 1. Snap the plastic upper chute support in place by first clipping the side portion onto the bagger support rail (1) with the edge of the snap feature aligned with the red line, as seen in the inset of Fig. 4-8. 2. Snap the front side of the chute support to the rail (2), as shown in Fig. 4-8. 2 1 Make sure scre
Краткое содержание страницы № 11
6. Slide the hinge pin into the hole located on the mounting 7. Open Hood by pushing in on the rear, right-side tab with tab, as in Fig. 4-12. Use the cut-out window (See inset in your right hand, as seen in 1 of Fig. 4-14, and lifting the cover Fig. 4-12) to line up the hinge pin on the other side and with your left hand in the center rear of the bagger cover, 2. push pin all the way in until it reaches the end-stop. At this point the pin clips into place and is secured by a tab in the bag
Краткое содержание страницы № 12
6. Move the wood block to either the left or right blade for Attaching Blades stabilization and remove and replace the center blade so that side of the blade with part number faces the ground WARNING! Always protect your hands while when the mower is in the operating position. servicing blades by wearing heavy work gloves or using heavy rags. NOTE: Save the three blades you just removed to use as replacements or to reinstall on the blade spindles when not NOTE: High-lift bagging blades a
Краткое содержание страницы № 13
NOTE: An extra carriage bolt and lock nut have been Installing the Chute Discharge Plate supplied in your bagger kit in hardware pack 689-00163. 1. Remove the discharge chute by removing the two flange You may replace the old hardware for the chute stop lock nuts securing it. bracket with this new hardware, or save for later use. 2. With a hammer, lightly tap the bolts out. Discard the bolts NOTE: This chute stop bracket may stay on the unit even and flange lock nuts. when the bagger is no
Краткое содержание страницы № 14
5. Rotate the chute around the deck so that its front edge fits 8. Peel the backing off of the self-adhesive foam strip (721- snugly into the deck opening. Lower the chute deflector 04388) that has been included with your grass collector. slowly (C in Fig. 4-21). Apply it to the upper chute, flush against the flange as shown in Fig. 24. 6. Attach the retainer strap on the discharge chute to the retainer clip on the deck. Refer to Fig. 4-22. Flange Figure 4-22 Figure 4-24 Note: For the chute e
Краткое содержание страницы № 15
Operation 5 3. Remove the grass bags, as shown in Fig. 5-2, by lifting each Bagger Usage bag up (1) and moving the bags away from the bag support NOTE: When all of the grass bags are full, place the tractor on a assembly (2). firm, level surface, disengage the PTO, turn the tractor engine off and set the parking brake. 1. Flip Seat up. 2. Lift up grass bag cover by pushing in on the rear, right-side tab with your right hand, as seen in 1 of Fig. 5-1, and lifting the cover with your left ha
Краткое содержание страницы № 16
19A40002100 Parts List A 17 2 5 18 16 12 19 22 8 4 20 21 13 32 11 6 12 A 5 9 35 10 3 12 6 24 6 7 27 15 12 24 30 23 25 28 34 26 23 21 31 22 29 14 1 16
Краткое содержание страницы № 17
Ref. Part Number Description 1. 931-04291 Upper Chute Assembly 2. 931-04298 Triple Bagger Cover Assembly 3. 731-06497 Upper Chute Support 4. 731-06504 Bagger Cover Screen 5. 710-0276 Carriage Screw, 5/16-18 x 1.00” 6. 710-3008 Hex Head Screw, 5/16-18 x .75” 7. 711-0309A Clevis Pin, .62” Dia. 8. 964-04090A Grass-bag Assembly 9. 683-04498A Triple Bag Support Assembly 10. 683-04519 Vertical Support Bracket 11. 711-05079 Cover Hinge Pin 12. 712-04063 Flange Lock Nut, 5/16-18 13. 735-0246A End Plug 1
Краткое содержание страницы № 18
Notes 18
Краткое содержание страницы № 19
19
Краткое содержание страницы № 20
CUB CADET LLC MANUFACTURER’S LIMITED WARRANTY FOR SEPARATELY SOLD ATTACHMENTS AND ACCESSORIES IMPORTANT: To obtain warranty coverage owner may be required a. Routine maintenance items such as lubricants, filters, blade to present an original proof of purchase and applicable maintenance sharpening, tune-ups, brake adjustments, clutch adjustments, deck records to the servicing dealer. Please see the operator’s manual for adjustments, and normal deterioration of the exterior finish due to infor
