Краткое содержание страницы № 1
Versa E6000
Disassembly Manual
Краткое содержание страницы № 2
Table of contents Overview.................................................................................................................................................................3 Technician Notes....................................................................................................................................................3 Disassembly Instructions....................................................................................................................
Краткое содержание страницы № 3
Overview This document contains step-by-steps disassembly instructions for the Versa E6000/EasyNote G5 chassis. The instructions are illustrated where necessary with images of the part that is being removed or disassembled. Furthermore, the screws that are removed are shown next to the image of the parts themselves. NEC reserves the right to make changes to the Versa E6000/EasyNote G5 chassis without notice. Technician Notes Only technicians authorized by NEC Computers International
Краткое содержание страницы № 4
WARNING Hazardous Voltage Ensure that the computer is disconnected from its power source and from all There is hazardous voltage present inside the computer telecommunications links, networks, or modem when it is connect to an AC supply, even when the lines whenever the chassis cover is removed. computer’s power switch is off. Exposure to hazardous Do not operate the computer with the cover voltage could cause personal injury. To avoid risk of injury, removed. contact an Authorized Se
Краткое содержание страницы № 5
Removing the Battery Perform the following steps to remove the battery: 1. Make sure to power off the Versa E6000/EasyNote G5. 2. Turn the unit upside down. 3. Unlock the battery and slide it out of its place as the arrow shows in Fig. 1 Fig. 1 Removing the battery NEC Versa E6000/PB Easy Note G5 Disassembly Manual Page 5
Краткое содержание страницы № 6
Removing the Memory Module To remove the Memory Module, first remove the battery (see Removing the Battery), then perform the following steps: 1. Release the one screw retaining the memory module cover. M2.5x5 Silver Fig. 2 Removing the screw retaining the memory module slot cover 2. Unclip the memory module as shown in Fig. 3 Fig. 3 Removing the memory module
Краткое содержание страницы № 7
Removing the MDC Modem To remove the MDC Modem, first remove the Memory Module Cover (see Removing Memory Module) then perform the following steps: 1. Release screws and disconnect cable on MCD Modem as shown in Fig. 4 M2.5x4 Silver Fig. 4 MDC Modem 2. Lift up the MDC modem and put it aside. NEC Versa E6000/PB Easy Note G5 Disasse
Краткое содержание страницы № 8
Removing the Hard Disk Drive To remove the hard disk drive, first remove the battery (see Removing the Battery), then perform the following steps: 1. Remove the screws as shown in Fig. 5 M2.5x4 Copper Fig. 5 Removing the Hard disk drive cover 2. Release the screws that secure HDD module as shown in Fig. 6 and carefully pull the HDD module out from the base unit. M3x8.5 Silver
Краткое содержание страницы № 9
Removing the Keyboard To remove the Keyboard, first remove the battery (see Removing the Battery), then perform the following steps: 1. Release the keyboard cover from the rear of the system as shown in Fig. 7 Fig. 7 Releasing the keyboard cover 2. Lift up the keyboard cover carefully and disconnect cable attached on it as shown in Fig. 8 Fig. 8 Lifting up
Краткое содержание страницы № 10
3. Lift up the keyboard and disconnect it from the system as shown in Fig. 9 M2.5x9 Silver Fig. 9 Disconnecting the keyboard flat cable Removing the Optical Disk Drive To remove the ODD, first remove the battery (see Removing the Battery) and remove the Keyboard (see Removing the Keyboard) then perform the following steps: 1. Remove the screws retaining the optical drive as shown in Fig. 10 M2
Краткое содержание страницы № 11
2. Flip over the unit, and push the ODD module out from the base unit as shown in Fig. 11 Fig. 11 Pushing the optical drive out from the base unit NEC Versa E6000/PB Easy Note G5 Disassembly Manual Page 11
Краткое содержание страницы № 12
Removing the LCD Module To remove the LCD Module first remove the battery (see Removing the Battery) and remove the Keyboard (see Removing the Keyboard) then perform the following steps: 3. Remove the screws retaining the Heat Plate as shown in Fig. 12 M2.5 x 5 Silver Fig. 12 Removing the screws retaining the Heat Plate 4. Flip over the base unit and release the screws retaining the LCD Module. M2.5x9
Краткое содержание страницы № 13
6. Open up the LCD lid, release the screws and the LCD cable connector. M2x4 Silver Fig. 15 Removing screws retaining LCD Cable Connector 7. Carefully lift up the LCD Module. Removing the WLAN Card Module To remove the WLAN Card Module first remove the battery (see Removing the Battery), remove the Keyboard (see Removing the Keyboard) and removing heat plate (see Removing the LCD Module) then perform the followin
Краткое содержание страницы № 14
Removing the LCD Panel To remove the LCD panel, first remove the LCD module (see Removing the LCD Module), then perform the following steps: 1. Use a pin to remove the rubber cover on the LCD module as shown in Fig. 17 2. Remove all screws as shown in Fig. 17 and remove carefully the LCD cover. M2.5x7 Silver Fig. 17 Removing the rubber covers & screws on the LCD Module 3. Release
Краткое содержание страницы № 15
4. Carefully lift up the LCD panel. 5. Remove the screws at both sides of the LCD panel in order to release the LCD hinges as shown in Fig. 19 M2x4 Silver Fig. 19 Removing the LCD Panel hinges Removing the CPU To remove the CPU first remove the battery (see Removing the Battery) and remove the Keyboard (see Removing the Keyboard) then perform the following steps: 1. Remove the screws retaining the Heat Plate as shown in Fig. 20
Краткое содержание страницы № 16
2. Remove the CPU Fan screws, disconnect the CPU Fan connector and remove the CPU Fan. M2.5x6.5 Silver Fig. 21 CPU Fan 3. Unscrew screws on CPU Heat Sink in descending order (3 2 1) as shown in Fig. 22 M2.5x4 Copper Fig. 22 CPU Heat Sink NEC Versa E6000/PB Easy Note G5 Disassembly Manual Page 16
Краткое содержание страницы № 17
Note: Beware of screws use on the CPU heat sink! Make sure to use the screw size M2.5x4, otherwise it might cause damage to the CPU die. When install heat sink, screws must be secured in ascending order (1 2 3). 4. Unlock the CPU from the CPU socket and lift up the CPU carefully. Fig. 23 Unlocking the CPU NEC Versa E6000/P
Краткое содержание страницы № 18
Removing the Top Cover To remove the Top Cover , first remove the battery (see Removing the Battery), remove the HDD (see Removing the Hard Disk Drive), remove the Optical Disk Drive (see Removing the Optical Disk Drive), remove the Keyboard (see Removing the Keyboard) and remove the LCD Module (see Removing the LCD Module) then perform the following steps: 1. Remove all screws on the bottom of the base unit as shown in Fig. 24 M2.5x9 Silver
Краткое содержание страницы № 19
2. Release all screws on the top cover as shown in Fig. 25 A = M2.5x5 Silver B=M2.5x6 Silver Fig. 25 Top Cover screws 3. Disconnect the Touch Pad Connector as shown in Fig. 26 Fig. 26 Touch Pad connection 4. Carefully lift up the Top Cover. NEC Versa E6000/PB Easy Note G5 Disassembly Manual Page 19
Краткое содержание страницы № 20
Removing the Touch Pad To remove the touch pad, first remove the top cover (see Removing the Top Cover), then perform the following steps: 1. Unscrew the screws on the Top Cover as shown in Fig. 27 M2x4 Silver Fig. 27 Touch Pad 2. Carefully separate the Touch Pad module from Top cover. NEC Versa E6000/PB Easy Note G5 Disassembly Manual P
