Краткое содержание страницы № 1
Batter Battery Charger/T y Charger/Tester ester
Batter Batter Battery Charger/T y Charger/T y Charger/Tester ester ester
12 V 12 Volt olt
12 Volt
12 V 12 Volt olt
94088
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 MISSION OAKS BLVD., CAMARILLO, CA 93011
VISIT OUR WEB SITE AT HTTP://WWW.HARBORFREIGHT.COM
TO HELP PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
© ®
Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion of this manual
or any artw
Краткое содержание страницы № 2
Specifications In tem Descriptio Pz ower Consumption 110 VAC, 60 H Pg ower Cord Six feet with 2-prong plu OC utput 2 or 5.5 amps at 12 Volts D Bs attery Charge Indicator 12.3-12.6 Volt C) harger Capacity 15-90 Ah (4 Volt Min. Charge O) verall Dimensions 4-3/8" (L) x 6-7/8" (W) x 11" (H W. eight 6.1 lbs IMPORTANT SAFEGUARDS IMPORTANT SAFETY INSTRUCTIONS 1. “SAVE THESE INSTRUCTIONS” - This manual contains important safety and operating instructions for battery charger Model: 94088. 2. Do not expos
Краткое содержание страницы № 3
9. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. 10. WARNING - RISK OF EXPLOSIVE GASES. (a) Working in the vicinity of a lead-acid battery is dangerous. Batteries generate explosive gases during normal battery operation. For this reason, it is of utmost importance that each time before using your charger, you read this and follow the instructions exactly. (b) To reduce the risk of the battery explosion, follow these instructions and t
Краткое содержание страницы № 4
(d) Add distilled water in each cell until battery acid reaches level specified by battery manufacturer. This helps purge excessive gas from cells. Do not overfill. For a battery without cell caps, carefully follow manufacturer’s recharging instructions. (e) Study all battery manufacturer’s specific precautions such as removing or not removing cell caps while charging and recommended rates of charge. (f) Determinate voltage of battery by referring to car owner’s manual and make sure that output
Краткое содержание страницы № 5
carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block. (g) When disconnecting charger, turn switches to off, disconnect AC cord, remove clip from vehicle chassis, and then remove clip from battery terminal. (h) See operating instructions for length of charge information. 16. Follow these steps when battery is outside vehicle. A spark near battery may cause battery explosion. To reduce risk of a spark near battery: (a) Check polarity o
Краткое содержание страницы № 6
Specific Safety Rules for the Battery Charger 1. Maintain labels and nameplates on the Battery Charger. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 2. Always wear safety impact eye goggles and heavy work gloves when using the Battery Charger. Using personal safety devices reduce the risk for injury. Safety impact eye goggles and heavy work gloves are available from Harbor Freight Tools. 3. Maintain a safe working environment. Keep
Краткое содержание страницы № 7
ASSEMBLY INSTRUCTIONS 1. When unpacking, check to make sure that the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. 2. This product comes preassembled. No additional assembly is necessary. OPERATING INSTRUCTIONS Warning: Do not overcharge maintenance- Front Panel free batteries. Do not try to start the engine with the Battery Charger connected to the battery. 1. FOLLOW ALL CONNEC
Краткое содержание страницы № 8
7. Connect the negative (black) Cable Clamp to the negative terminal of the battery. 8. Plug the Power Cord into the electrical outlet. 9. The LEDs on the charging table on the left side of the front panel will indicate the voltage and charge status of the battery. Note: If the unit emits a buzzing sound, the cables are connected to the wrong terminals of the battery. If this happens, immediately switch off the charger, unplug it, and switch the connections. 10. When the battery is fully charged
