Краткое содержание страницы № 1
AN-CM270
INSTALLATION INSTRUCTIONS FOR
CEILING MOUNTING BRACKET FOR
USE ONLY WITH SHARP
PROJECTOR MODEL
XV-Z2000/DT-400
CEILING MOUNTING
BRACKET AN-CM270
CEILING MOUNTING
BRACKET COMBINED
WITH OPTIONAL
ADJUSTABLE
EXTENSION TUBE
MODEL AN-EP101B
2004 SHARP ELECTRONICS CORPORATION
COPYRIGHT ©
Краткое содержание страницы № 2
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 C A U C A U T T I O I O N N C A U C A U T T I O I O N N INSTALLATION OF THIS ADJUSTABLE WALL MOUNTING BRACKET SHOULD BE PERFORMED BY QUALIFIED SERVICE/INSTALLATION PERSONNEL FOLLOWING THE INSTALLATION INSTRUCTIONS INCLUDED WITH THIS BRACKET THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTE
Краткое содержание страницы № 3
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 FIGURE 1. ILLUSTRATION OF PARTS FOR CEILING BRACKET A. B. C. D. K. E. H. I. F. J. G. INVERT THE PROJECTOR IMAGE Please refer to the owners manual for your LCD Projector for detailed instructions of how to electrically invert the projected image to accommodate its use in the ceiling mounted mode. LOCATION OF THE CEILING BRACKET Please ref
Краткое содержание страницы № 4
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 1.1 a. Select straddle beam or single beam installation. b. Use the ceiling bracket as a template to mark the location where the pilot holes should be drilled. c. Drill the pilot holes for the support screws using a 1/8” drill bit into the center of the beam. (See Figs. 2 and 3). 1.2 Screw the ceiling plate
Краткое содержание страницы № 5
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 FIGURE 3 ILLUSTRATION OF SINGLE BEAM CEILING BRACKET INSTALLATION Ceiling Beam Ceiling Mounting Bracket Washers Sheetrock or lath and plaster ceiling 1/4 x 10 Lag Bolts Velcro DO NOT RUN THE AC POWER CORD THROUGH THE CEILING PLATE AND TRIM COVER STEP 2. INSTALL THE CEILING MOUNT PLASTIC TRIM 2.1 The Access Hole (See Fig. 4) in the ceiling attachment plate is large enough to accommodate
Краткое содержание страницы № 6
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 STEP 3 DETACH THE POSITIONING ASSEMBLY FROM THE PROJECTOR ATTACHMENT PLATE. NOTE: PLEASE LOOK OVER THE EXACT MANNER IN WHICH THE FIGURE 5 POSITIONING ASSEMBLY AND THE ATTACHMENT PLATE GO TOGETHER SO THAT YOU WILL BE ABLE TO REASSEMBLE THEM WHEN YOU HANG THE PROJECTOR. 3.1 Using 9/16” box wrench, remove the nut from the lower knuckle (vertical position) and slide the center a
Краткое содержание страницы № 7
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 4.3 Fold the attachment plate down on its hinge. See Fig. 8 4.4 Install the M4 knurled thumb screw by hand. See Fig. 8. DO NOT USE TOOLS TO TIGHTEN THIS SCREW. M4 Knurled Thumb Screw FIGURE 8 REMINDER: MAKE SURE TO ALLOW SUFFICIENT SLACK IN THE WIRING TO PERMIT THE PROJECTOR TO SWING DOWN ON THE HINGE TO ALLOW EASY SERVICING OF THE FILTER AND THE LAMP ASSEMBLY. STEP 5 ATTACH THE POSI
Краткое содержание страницы № 8
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 5.3 Place the plastic trim cover in position over the ceiling plate and press the Velcro tabs together. 5.4 After completing step #5.3, screw the longer shaft with the locking nut and washer into the center threaded bushing on the ceiling plate as far as it will go. (See Fig. 9) 5.5 Tighten the locking nut against the ceiling plate using a 3/4” open end wrench or an
Краткое содержание страницы № 9
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 FIGURE 11 DETAIL OF POSITIONING ASSEMBLY CEILING PLATE PLASTIC CEILING PLATE TRIM COVER LOCKING NUT AND HORIZONTAL POSITION ADJUSTMENT HORIZONTAL TILT ADJUSTMENT VERTICAL POSITION ADJUSTMENT STEP 8 INSTALL THE PLASTIC TRIM COLLAR 8.1 The plastic trim collar may be used as a cosmetic concealment of the positioning adjustment knuckle assembly and the audio and video signal cab
Краткое содержание страницы № 10
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 PROCEDURE FOR SERVICING LAMP HOUSING OR AIR FILTER: A. Remove the knurled thumb screw. See Fig. 14. The projector will swing down on the hinge of the mounting bracket. The bottom of the projector will now be in a position to permit servicing the lamp assembly. B. Proceed to service the air filter or the lamp assembly. Follow the appropriate instructions in your projector owner’s manual.
Краткое содержание страницы № 11
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 DIMENSIONS AND MEASUREMENTS OF COMPONENTS FOR SHARP MOUNTING BRACKET AN-CM70 CEILING PLATE 4” WIDE X 18” LONG DISTANCE BETWEEN SETS OF MOUNTING HOLES: 1st SET 12”, 2nd SET 14”, 3rd SET 16” ADDITIONAL POSSIBLE COMBINATIONS OF MOUNTING HOLE DISTANCE 13” & 15” THREAD SIZE OF SWIVEL SHAFT & CEILING PLATE BUSHING 1/2” X 20 15 ” VEL- 4” VEL- 12” 14” 16” 18” CABLE ACCESS HOLE CENTER BUSHI
Краткое содержание страницы № 12
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 ONE YEAR LIMITED WARRANTY SHARP Electronics Corporation warrants to the first end use purchaser, that this SHARP brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective product or part thereof at no charge to the purchaser for parts or for l
