Краткое содержание страницы № 1
45602
Wireless Lighting Control
On/Off/Dim
Lamp Module
™
GE SmartHome
®
Z-Wave Certified
Wireless Lighting Control
Краткое содержание страницы № 2
Introduction: ® Thank you for your purchase of a GE Z-Wave control ® device. Z-Wave technology is designed to automate lighting/home control and provide easy remote operation of ® ® all your Z-wave enabled devices. The GE Z-Wave product family includes a variety of devices to control lighting in your home. It is up to you whether you want to control one room or your entire house and whether you want to do it all now or start with one room and add more over time. This module is one
Краткое содержание страницы № 3
to the system and will also act as range extenders if they support this function of repeating the signal received to other nodes in the system. Manual/Program button Standard AC outlet Z-wave outlet (other end) The incandescent lighting plugged into the ® Z-Wave controlled outlet on this module must not exceed 300 watts. DO NOT use with fluorescent lighting. Plugging a non-resistive load such as fluorescent lighting or a device with a motor into the ® Z-Wave controlled outlet ma
Краткое содержание страницы № 4
There are no user serviceable parts in this unit. To reduce the risk of electric shock, this product has a grounding type plug that has a third (grounding) pin. This plug will only fit into a grounding type power outlet. If the plug does not fit into the outlet, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. WARNING RISK OF FIRE The Load-Sense feature on RISK OF ELECTRICAL SHOCK this Z-Wave product will turn RISK OF BURNS the power to the
Краткое содержание страницы № 5
4. Do Not use Z-Wave devices to control electric heaters or any other appliances which may present a hazardous condition due to unattended or unintentional or automatic power on control. 5. Double check programs for accuracy before using them. Wireless Range This device complies with the Z-Wave standard of open- air, line of sight transmission distances of 65 feet. Actual performance in a home depends on the number of walls between the remote controller and the destination device, the type
Краткое содержание страницы № 6
Effects of Home Construction on Wireless Range Between Z-Wave Enabled Devices. Note: The distances shown in the table below are typical examples. Actual performance in your home will vary. From the Remote (or repeating Z-Wave module) to destination device: Type of Construction Wood Frame Brick, Tile or w/Drywall Concrete Plastic Metal Plastic Metal J-Boxes* J-Boxes J-Boxes* J-Boxes ** 0 100’ 80’ 100’ 80’ Number 1 70’ 56’ 60’ 48’ of Walls or Obstacles 2 49’ 39’ 36’ 29’ 3 34’ 27’ 21’ 17’ *
Краткое содержание страницы № 7
Please Note: Z-Wave home control networks are designed to work properly alongside 802.11 wireless computer networks, Bluetooth and other 2.4GHz or 5.8GHz devices. Some baby cams, wireless video devices and older cordless phones using the 900MHz frequency range may cause interference and limit Z-Wave functionality. Many 900MHz products have a switch to select channel “A” or “B”. You may find that one of these channels will cause less interference than the other. Key Features: - One Z-w
Краткое содержание страницы № 8
Basic Operation The connected light can be turned ON in three ways: 1. With a Z-wave remote. 2. Manually with the pushbutton on the Z-Wave module. 3. By the Load-Sensing feature. Normally, the Z-Wave module controls the ON/Off state of the connected light and power is either turned On or Off at the module (either manually or by the remote). If the switch on the connected light is used, the Z-Wave control circuitry automatically senses that the light is being turned On and activates the
Краткое содержание страницы № 9
2. Adjust the brightness level of the connected lighting by pressing and holding the button. Release the button when the desired level is attained. - This is also a toggle function. The lighting will dim until the minimum level is attained or the button is released. The next time the button is pressed and held, the level will increase until the maximum level is attained or the button is released. 3. Include or exclude the module from the Z-Wave home control network with your prim
Краткое содержание страницы № 10
All On/All Off Depending upon your primary controller, the 45602 lamp module can be set to respond to ALL ON and ALL OFF commands in up to four different ways. Some controllers may not be able to change the response from its default setting. Please refer to your controller’s instructions for information on whether or not it supports the configuration function and if so, how to change this setting. The four possible responses are: - It will respond to ALL ON and the ALL OFF commands (d
Краткое содержание страницы № 11
Dim Rate Adjustments Both the number of steps (or levels) that the dimmer will change and the timing of the steps can be modified to suit personal preferences. The timing of the steps can be adjusted in 10 millisecond intervals. As an example, the default setting for parameter 8 is “3”. This means that the lighting level will change every 30 milliseconds when the Dim Command is received. A value of 255 would mean that the level would change every 2.55 seconds. Combined, the two param
Краткое содержание страницы № 12
Ignore Start Level When Receiving Dim Commands Please note: Every “Dim” command from your remote controller includes a start level embedded in it. The 45602 can be set to ignore the start level that is part of the dim command. Setting parameter 5 to a value of 0 will cause the 45602 to dim or brighten from the start level embedded in the command. - Parameter No: 5 - Length: 1 Byte - Valid Values = 0 or 1 (default 1) Restoring Factory Defaults All Configuration Parameters can all be re
Краткое содержание страницы № 13
™ Interoperability with Z-Wave Devices ™ A Z-Wave network can integrate devices of various classes, and these devices can be made by different manufacturers. Although every Z-Wave certified product is designed to work with all other Z-Wave certified products, your controller must include the appropriate device classifications in order to control non-lighting Z-wave devices. As an example, the GE 45600 Basic Remote is designed only for controlling Z-Wave devices using the lighting control
Краткое содержание страницы № 14
FCC U2Z45602-3 The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses, generates and can radiate radio frequency energy and, if not installed and used in accordance
Краткое содержание страницы № 15
Important Note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. Compliance with IC Rules and Regulations IC: 6924A-45602A3 Jasco Products Company Model: 45602 This Class B digital device complies with Canadian ICES-003. SPECIFICATIONS Power 120VAC, 60Hz Signal (Frequency) 9
Краткое содержание страницы № 16
is a registered trademark of General Electric Company and is used under license to J asco Products Company LLC, 10 E Memorial Rd., Oklahoma ™ GE SmartHome City, Oklahoma 73114 Made in China Hecho en China All brand names shown are trademarks of their respective owners. Todas las marcas que aparecen aquí son marcas registradas de sus respectivos dueños.
