Краткое содержание страницы № 1
®
COMBO RATCHET/IMPACT SET
Assembly and Operating Instructions
®
3491 Mission Oaks Blvd. / Camarillo, CA 93011
®
Copyright © 1997 by Harbor Freight Tools . All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in any
shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
REVISED 12/02 05/04
Краткое содержание страницы № 2
SPECIFICATIONS RATCHET WRENCH — Average Air Consumption 4 CFM Recommended Air Pressure 90 PSI Air Inlet ¼” NPT Free Speed 150 RPM Maximum Torque (ft. lbs.) 45 IMPACT WRENCH — Bolt Capacity 1/2" Speed 7000 RPM Air Inlet ¼” NPT Sockets 7/16" – 1" Maximum Torque (ft. lbs.) 230 SAVE THIS MANUAL You will need the manual for the safety warnings and cautions, assembly instructions, operating procedures, maintenance procedures, trouble shooting, parts list, and diagram. Keep your invoice with this manua
Краткое содержание страницы № 3
6. USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. Do not use a tool for a purpose for which it was not intended. 7. DRESS PROPERLY. Do not wear loose clothing or jewelry as they can be caught in moving parts. Non-skid footwear is recommended. Wear restrictive hair covering to contain long hair. 8. USE EYE AND EAR PROTECTION. Always wear ANSI-approved chemical splash goggles when working with chemicals. Always wear AN
Краткое содержание страницы № 4
18. DRAIN COMPRESSOR EVERY DAY. Do not allow moisture to build up inside the compres- sor. Do not allow compressor to sit pressurized for longer than one hour. 19. MAKE SURE ALL EQUIPMENT IS RATED TO THE APPROPRIATE CAPACITY. Make sure that the regulator is set at least 10 PSI lower than the lowest rated piece of equipment you are using. 20. DO NOT USE OXYGEN, COMBUSTIBLE GASES, OR BOTTLED GASES AS A POWER SOURCE. The tool may explode, possibly causing injury. 21. DO NOT EXCEED the recommended a
Краткое содержание страницы № 5
GROUNDING INSTRUCTIONS If compressor has a three-prong plug 1. This machine has a three-prong plug. The third prong (round) is the ground. Plug the machine’s cord only into three-prong receptacles. Never cut off the round prong. Cutting off the ground will result in a safety hazard and void the warranty. 2. If a three-prong receptacle is not available, you may use an adapter. Extending from the male end of the adapter, you will find a ring connector or wire lead with a ring connector where the g
Краткое содержание страницы № 6
UNPACKING When unpacking, check to make sure the following parts are included. All sizes listed below are approximate. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Item# Description Item# Description N/A 3/8" Ratchet Wrench N/A Impact Sockets (7/16" – 1") N/A 1/2" Impact Wrench N/A Oil Pot N/A 3/8" to 1/2" Adapter N/A Air Coupler N/A 4mm Hex Wrench ASSEMBLY Your Air Ratchet comes completely assembled. Air Connection for Ratchet S
Краткое содержание страницы № 7
OPERATION Setup Frequent, but not excessive, lubrication is required for best performance. Oil added through the airline connection will lubricate internal parts. An automatic airline oiler is recommended but oil may be added manually before every operation or after about 1 hour of continuous use. Only a few drops of oil at a time are necessary. Too much oil will collect inside the tool and be blown out during the exhaust cycle. ONLY USE PNEUMATIC TOOL OIL. Do not use detergent oil or addi
Краткое содержание страницы № 8
Air Ratchet Operation Step 1: Select the appropriate socket for your needs. Step 2: Attach the socket to the RATCHET ANVIL (#18) as shown in Figure 2. 123456 123456 123456 123456 123456 123456 123456 123456 123456 123456 Air Inlet Roll Pin (#5) Figure 2 — Attaching the Socket Step 3: Set the compressor’s pressure regulator to 90 PSI. Do not set the compressor’s outlet regulator over 90 PSI. Step 4: Connect the Air Ratchet to the air compressor’s hose. If leaking is detected, discon- nect the
Краткое содержание страницы № 9
Loosening Step 1: Check the direction of the drive by pressing the TRIGGER (#4) as shown in Figure 3. 1234567 1234567 1234567 123456 1234567 123456 1234567 123456 123456 123456 123456 Figure 3 — Operating the Air Ratchet Step 2: If the Air Ratchet is going counterclockwise (the correct direction to loosen), then proceed to Step 4. Step 3: To change the direction of the drive to loosen, turn the dial marked “R-F” clockwise as shown in Figure 4. Figure 4 — Changing Direction of the Driv
Краткое содержание страницы № 10
Tightening Step 1: Check the direction of the drive by pressing the TRIGGER (#4) as shown in Figure 3. Step 2: If the Air Ratchet is going clockwise (the correct direction to tighten), then proceed to Step 4. Step 3: To change the direction of the drive in order to tighten, turn the dial marked “R-F” counterclockwise as shown in Figure 5 Figure 5 — Changing the Direction of the Drive Step 4: Thread the nut on as far as you can by hand. Step 5: Place the socket on the nut. To begin tighten
Краткое содержание страницы № 11
MAINTENANCE Your Air Ratchet is best operated with an Airline Oiler. If you are using the Air Tool without an Airline Oiler, follow the steps below. Step 1: Disconnect the Air Ratchet from the air hose. Step 2: Apply a few drops of PNEUMATIC TOOL OIL through the air inlet before each use, CAUTION or every hour if used continuously. Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seals in the tool. Step 3: Apply a few drops of oil to the VALVE (#6)
Краткое содержание страницы № 12
Impact Wrench Operation Step 1: Set the compressor’s pressure regulator to a maximum of 90 PSI. 90 PSI is satisfac- tory without harming this tool. Step 2: Remove the plastic cap from the rear of the HOSE ADAPTER (#10). Step 3: Wrap the threads of the Air Coupler with pipe thread seal tape (not included). Attach the Air Coupler to the HOSE ADAPTER. Tighten the fitting. Step 4: Determine the socket size necessary for the job you need to do. Attach the appropriate 1/2” drive socket to the I
Краткое содержание страницы № 13
Step 6: Select the power setting for Loosening by pushing in and turning the AIR REGULATOR (#11) located on the bottom of the CAUTION Impact Wrench as shown in Figure 8. Use the Setting Appropriate for the When the AirRegulator is completely Job. Do Not Set the Power Setting screwed in it is at it’s lowest setting. Higher Than Needed. Damage to Air pressure increases as you push in Parts Could Result. and turn the Air Regulator. Figure 8 — Adjusting the Reverse Power Setting Step
Краткое содержание страницы № 14
Step 8: Press the TRIGGER (#4) to test the Impact Wrench. The Impact Wrench should spin freely as shown if Figure 10. Figure 10 — Pressing Trigger Loosening Step 1: Verify that the power level is correct for your needs and that the REVERSE VALVE (#3) has been shifted (pressed) completely to the right. If not, refer to Steps 6 through 7 under Impact Wrench Operation before proceeding. Step 2: Place your work in as clear a location as possible. Make sure the air hose will reach as far as n
Краткое содержание страницы № 15
Tightening Step 1: Verify that the power level is correct for your needs and that the REVERSE VALVE (#3) has been shifted (pressed) completely to the left. If not, refer to Steps 6 through 7 under Impact Wrench Operation before proceeding. Step 2: Place your work in as clear a location as possible. Make sure the air hose will reach as far as needed without stressing any connections. Step 3: Thread the nut or bolt on as far as possible by hand. This is to prevent cross-thread- ing. Step 4: If
Краткое содержание страницы № 16
PARTS LIST – RATCHET WRENCH Item# Parts No. Description Item# Parts No. Description 1 HY150-01 Housing 23 HY150-23 Ratchet Yoke 2 HY150-02 Connection Head 24 HY150-24 Cylinder 4 HY150-04 Trigger 25 HY150-25 Rotor 5 HY150-05 Roll Pin 26 HY150-26 Rotor Blade 6 HY150-06 Valve 27 HY150-27 Front Plate 7 HY130-18 O-Ring 28 HY150-28 Front Bearing 8 HY150-08 Spring 29 HY150-29 Rear Plate 9 HY150-09 Valve Plug 30 HY150-30 Rear Bearing 10 HY160-12 O-Ring 31 HY150-31 Cylinder Pin 11 HY150-11 Washer 32 HY15
Краткое содержание страницы № 17
Exploded View Diagram - Ratchet Wrench For technical questions, please call 1-800-444-3353. Page #17 -- SKU: 33567 REV 12/02
Краткое содержание страницы № 18
PARTS LIST – AIR IMPACT WRENCH Item# Parts No. Description Item# Parts No. Description 1 16001 Housing 23 16023 Ball Bearing (X2) 2 16002 Valve Sleeve 24 16024 Cylinder 3 16003 Reverse Valve 25 16025 Rotor 4 16004 Trigger 26 16026 Rotor Blade (X6) 5 16005 Spring Pin 27 16027 Front End Plate 6 16006 Valve Stem 28 16028 Spring Pin 7 16007 Bushing 29 16029 Rear End Plate 8 16008 Steel Ball 30 16030 Spring Pin 9 16009 Spring 31 16031 Oil Seal 10 16010 Hose Adapter 32 16032 Rear Gasket 11 16011 Air R
Краткое содержание страницы № 19
Exploded View Diagram -- Air Impact Wrench For technical questions, please call 1-800-444-3353. Page #19 -- SKU: 33567 REV 12/02
