Краткое содержание страницы № 1
DECT Baby Monitor
SCD590
Краткое содержание страницы № 2
Краткое содержание страницы № 3
9 10 12 1 4 5 1 2 11 13 6 7 8 3 5 6 1 7 11 2 8 3 12 4 9 10 13 14 16 15 17
Краткое содержание страницы № 4
Краткое содержание страницы № 5
EngliSh 6 SCD590
Краткое содержание страницы № 6
6 EngliSh introduction Philips Avent is dedicated to producing caring, reliable products that give parents the reassurance they need. This Philips Avent baby monitor provides round-the-clock support by ensuring you can always hear your baby clearly without any distracting noise. The DECT technology guarantees zero interference from other wireless appliances and a clear signal between the baby unit and the parent unit. This appliance comes with two parent units and two chargers instead of on
Краткое содержание страницы № 7
EngliSh 15 Do not place this product on an unstable cart, stand or table.The product may fall and sustain serious damage. 16 Make sure the baby unit and the power cord are always out of reach of the baby (at least 1 meter/3 feet away). 17 Never place the baby unit inside the baby’s bed or playpen. 18 Never cover the baby monitor (with a towel, blanket, etc.). if your product utilizes batteries, the following additional precautions should be observed: 1 Use only the type and size of batterie
Краткое содержание страницы № 8
EngliSh Compliance information The FCC ID number is located on the casing bottom of the parent unit and in the battery compartment of the baby unit. The term ‘IC’ before the certification number signifies that Industry Canada technical specifications were met. This certification means that the equipment meets certain radio communications and operational requirements. This device complies with Part 15 of the FCC Rules and ICES-003 of Industry Canada. Operation is subject to the following tw
Краткое содержание страницы № 9
EngliSh 10 Small plug 11 Battery compartment lid 12 Inlet for small plug 13 Battery compartment B Parent unit (2 pieces, only one is shown) 1 TALK button 2 LINK light 3 SENSITIVITY button 4 On/off button 3 5 Opening for belt clip and neck strap 6 Sound level lights 7 Volume +/– buttons 8 Battery check light T 9 Microphone 10 Loudspeaker 11 Battery compartment 12 Belt clip 13 Battery compartment lid 14 Neck strap 15 Adapter 16 Charger 17 POWER light C Travel pouch Preparing for
Краткое содержание страницы № 10
10 EngliSh Battery operation The parent unit runs on two rechargeable 1.2V AAA NiMH batteries that are supplied with the appliance. Make sure your hands and the unit are dry when you insert the batteries. 1 Slide the battery compartment lid downwards to remove it (Fig. 6). Insert the two rechargeable batteries (Fig. ). , Make sure the + and – poles of the batteries point in the right direction. Slide the battery compartment lid back onto the back of the parent unit until it locks in
Краткое содержание страницы № 11
EngliSh 11 , The LINK light flashes red briefly and then starts to flash green while the parent unit tries to establish connection with the baby unit. , The LINK light on the parent unit flashes green until connection has been established. This takes up to 0 seconds. The LINK light on the parent unit then lights up green continuously (Fig. 1). , If no link is established after 30 seconds, the LINK light on the parent unit flashes red and the parent unit beeps from time to time. Place
Краткое содержание страницы № 12
1 EngliSh Briefly press the volume + and – buttons on the parent unit until the desired microphone sensitivity level for the baby unit has been reached. Note: If you press the SENSITIVITY button and/or the volume + and – buttons too long, the microphone sensitivity is not adjusted. - one light on = minimum sensitivity level - all lights on = maximum sensitivity level Note: When the microphone sensitivity of the baby unit is set to a high level, it picks up more sounds and therefore tran
Краткое содержание страницы № 13
EngliSh 1 Connecting the belt clip 1 Insert the small pin on the back of the belt clip into the opening on the back of the parent unit (1). Turn the belt clip to the left () until it locks into position (‘click’) (Fig. ). Disconnecting the belt clip 1 Turn the belt clip to the right (1) and take it out of the opening () (Fig. 5). Connecting the neck strap 1 Insert the small pin at the end of the neck strap into the opening on the back of the parent unit (1). Turn the neck strap to
Краткое содержание страницы № 14
1 EngliSh Please inform yourself about the local separate collection system for electrical and electronic products. Please act according to your local rules and do not dispose of your old products with your normal household waste. The correct disposal of your old product helps prevent potential negative consequences for the environment and human health. Assistance For assistance, call toll-free: 1-800-243-7884 or visit our website: www. philips.com Information is available 24 hours a day, 7
Краткое содержание страницы № 15
EngliSh 15 Frequently asked questions This chapter lists the questions most frequently asked about the appliance. If you cannot find the answer to your question, contact the Customer Care Centre in your country. Question Answer Why don’t the ON light Perhaps the batteries of the parent unit are empty and the parent on the baby unit and the unit is not in the plugged-in charger. Put the adapter of the charger LINK light on the parent in the wall outlet and place the parent unit in the charger.
Краткое содержание страницы № 16
16 EngliSh Question Answer Why does the parent unit The microphone sensitivity level of the baby unit may be set too low. react slowly to the baby’s Increase the microphone sensitivity level with the SENSITIVITY crying? button on the parent unit. Why do the batteries of The microphone sensitivity level of the baby unit may be set too the baby unit run low high, which causes the baby unit to transmit more often. Decrease quickly? the microphone sensitivity level with the SENSITIVITY button on
Краткое содержание страницы № 17
EngliSh 1 Question Answer The microphone sensitivity level of the baby unit may be set too high, which causes the parent unit to consume a lot of energy. Decrease the microphone sensitivity level with the SENSITIVITY button on the parent unit. Why doesn’t battery It may take a few minutes before the battery check light lights up check light on the parent when you charge the parent unit for the first time or after a long unit light up when I start period of disuse. to recharge the parent u
Краткое содержание страницы № 18
1 5 6 10 11 1 1 1 15 16 1 1 1 0 1
Краткое содержание страницы № 19
1 5 6
Краткое содержание страницы № 20
4222.002.6467.2
