Краткое содержание страницы № 1
. .
Vandal-proof Tamper Detection PoE
Quick Installation Guide
Français Deutsch Italiano Türkçe Polski Русский Česky Svenska
English Español Português
FD7130
This guide describes the basic functions of FD7130
All detailed information is described in the user's manual.
IP Surveillance
Краткое содержание страницы № 2
Warning Before Installation Power off the Network Camera as Keep the Network Camera soon as smoke or unusual odors are away from water. If the Network detected. Camera becomes wet, power off immediately. Contact your distributor in the event of Contact your distributor in the event of occurrence. occurrence. Do not place the Network Camera Refer to your user’s manual for around heat sources, such as a the operating temperature. television or oven. Keep the Network Camera away from Do not pl
Краткое содержание страницы № 3
Do not place the Network Camera Do not touch the Network Camera on unsteady surfaces. during a lightning storm. Do not disassemble the Network Do not drop the Network Camera. Camera. Do not insert sharp or tiny objects into the Network Camera. EN - 2
Краткое содержание страницы № 4
1 Package Contents Liquid Tight Connectors for FD7130 with an RJ45 or M12 Cable RJ45 or M12 Cable RJ45 RJ45 M12 Software CD Alignment Sticker Quick Installation Guide / Ground Wire / Screws Warranty Card Screwdriver Silica Gel EN - 3 English
Краткое содержание страницы № 5
2 Physical Description Inner View Screw Holes Lens MicroSD/SDHC Card Slot Temperature Alarm Status LED The alarm will be triggered once the temparature inside the Network Camera reaches 60°C. Reset Button Outer View Record the MAC address before installing the camera. Network Camera Model No: FD7130 MAC:0002D107258A RoHS This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this
Краткое содержание страницы № 6
3 Cabling Assembly RJ45 Cable Connector RJ45 Cable Dimension (unit: mm) Components of the Waterproof Connector Sealing Nut (A) Seal (B) Screw Nut (C) Housing (D) Gasket (E) Assembling Steps 1 Prepare an Ethernet cable 2 Insert the housing into the 3 Insert the seal into the housing. screw nut. and strip part of the sheath. (C) (D) (B) Recommended cable gauge: 24AWG (0.51 mm) 4 Insert the stripped Ethernet 5 6 Push the RJ45 plug into the Clamp the cable with cable through the sealing housing
Краткое содержание страницы № 7
M12 Cable Connector M12 Cable Dimension (unit: mm) Components of the Waterproof Connector Sealing Nut (A) Seal (B) Clamp Ring (C) Gasket (D) Plastic Nut (E) Assembling Steps 1 3 Prepare an Ethernet cable 2 Insert the seal into the clamp Insert the gasket into the clamp and strip part of the sheath. ring. ring. (C) (B) (D) Ø4.5mm~Ø6.5mm Insert the stripped Ethernet Follow the pin definition in the below table 4 5 cable through the sealing nut to solder the stripped Ethernet cable to the and th
Краткое содержание страницы № 8
4 Hardware Installation First, use the supplied screwdriver to detach the dome cover from the camera base. Insert your MicroSD/SDHC Card if necessary. Tamper-proof Screw Dome Cover Rubber Stopper Camera Base Then, follow the steps below to install the camera to either the ceiling or the wall: 1. Attach the supplied alignment sticker to the ceiling/wall. 2. Using the 3 screw circles on the sticker, drill 3 pilot holes into the ceiling/wall. Then hammer the plastic anchors into the holes. 3. Th
Краткое содержание страницы № 9
Wall Mount 1 2 B A 3 4 Please secure the screws tightly to avoid moisture. Installing the Ground Wire As shown in the following figure, please secure one side of the supplied ground wire to the screw hole, then route the other side of the ground wire to the ground. EN - 8
Краткое содержание страницы № 10
PARTITION PARTITION LINK RE C E IV E POWE R COLLISION 1 2 3 4 5 LINK RE C E IV E POWE R COLLISION 1 2 3 4 5 Network Deployment 5 Power over Ethernet (PoE) When using a PoE-enabled switch This Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the camera to a PoE-enabled switch via Ethernet cable. PoE Switch When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Ca
Краткое содержание страницы № 11
6 Assigning an IP Address 1. Install “Installation Wizard 2” from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment. After your network is ana- lyzed, please click on the “Next” button to continue the program. Installation Wizard 2 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After searching, the main installer window will pop up. Click on the MAC that matches t
Краткое содержание страницы № 12
7 Ready to Use 1. Access the Network Camera on the LAN. 2. Retrieve live video through a web browser or recording software. For further setup, please refer to the user's manual on the software CD. 8 Adjusting the Lens To adjust the viewing angle Adjust the lens to a desired viewing angle as the diagram shown below. 10° 90° 10° DO NOT over rotate the lens. Doing so will damage the camera lens module. EN - 11 English
Краткое содержание страницы № 13
Fine-tune the Camera Focus The focus of this network camera is set from 1.0m to infinity by factory default. If you want to focus on objects closer than 1.0m or the lens has lost focus, please fine tune it in the following way. 1. Loosen the lens lock screw. 2. Manually rotate the lens to fine-tune the focus until the live image is clear. 3. Tighten the lens lock screw. Tighten the lens lock screw. Completion 9 Tear down the aluminum foil vacuum bag and take out the silica gel. Attach the suppli
Краткое содержание страницы № 14
P/N: 625008801G Ver.1.1 Copyright 2009 VIVOTEK INC. All right reserved.
