Краткое содержание страницы № 1
Ketec, Inc
Shoplifting Protection
USERS GUIDE
SP-1
KT7060
24501
Краткое содержание страницы № 2
SP-1 USERS GUIDE INDEX Parts List …………………………….1 Assembly Instructions……………… 2 Positioning the System ……………. 3 Tagging Guidelines …………………4 Removing Hard Tag……………….. 7 Detection Area ……………………... 9 Alarm Handling …………………….. 10 Troubleshooting ……………………. 11 Warranty…………………………….. Back Cover
Краткое содержание страницы № 3
PARTS LIST Remove all contents from packaging. Compare products with the example. If you are missing any parts please contact your supplier immediately. The carton should contain: SP-1 ANTENNA WITH WIRE BASEPLATE CAP NUTS AND WASHERS POWER SUPPLY WITH 10’ OF CORD 5’ RUBBER MOLDING & DOUBLE SIDED TAPE 1
Краткое содержание страницы № 4
ASSEMBLY INSTRUCTIONS 1. Locate the baseplate, cap nuts and washers. 2. Place the antenna on top of the baseplate, aligning the holes in the antenna base with the studs on the baseplate. Make sure that the power supply wire is in the channels of the antenna base and is not crushed between the antenna base and the baseplate. 3. Attach the washers and cap nuts to the bolts on the baseplate. DO NOT TIGHTEN. 4. Again make sure that t
Краткое содержание страницы № 5
POSITIONING THE SYSTEM 6. Position the system a minimum of 18” (Inches) from the doorframe and on the side closest to the door handle. 7. Cut the rubber molding to the length that will allow it to cover the wire from the wall to the system. You must cover the wire, using a metal pancake molding If the wire is in an area where it will be walked upon. 8. Insert the system power wire into the rubber pancake molding through the slit on t
Краткое содержание страницы № 6
TAGGING GUIDELINES 1. The tag should be visible to the customer. 2. Tag uniformly, it speeds up removal. 3. Tag near a price label. It assists in the removal. 4. Place the tag as high as possible when tagging silks & light or stretchy fabrics. 5. Except for leather goods we do not recommend locating the tag at the seams. The seams are easily cut open to remove the pin. 6. Avoid placing tags on waistbands, cuffs, hems o
Краткое содержание страницы № 7
TAGGING GUIDELINES Dresses Pants Bikini Bathing Suit One Piece Bathing Suit 5
Краткое содержание страницы № 8
TAGGING GUIDELINES Shoes Tennis Shoes Belts Purses 6
Краткое содержание страницы № 9
REMOVING HARD TAG 1. Place the hard tag into the detacher with the pin facing up. 2. Remove the pin by holding the hard tag to the detacher and pulling straight up on the pin or garment. 3. Remove the pin and hard tag from the detacher and store for future use. 7
Краткое содержание страницы № 10
REMOVING HARD TAG It is possible for the locking mechanism to become jammed when the pin is pulled extremely hard. It is possible to un-jam the pin so that you will be able to remove it when needed. The first step is to place the hard tag into the detacher then press on the head of the pin. This should release the pressure on the locks allowing you to remove the pin. If you are still unable to release the pin you can tap the locking mechanism (raised area)
Краткое содержание страницы № 11
DETECTION AREA The SP-1 system will detect hard tags within 4 feet to each side and 3 feet in front of and back of the antenna. We recommend that you keep all merchandise with hard tags a minimum of 4-1/2 feet from the sides of the system and 3 feet from the front of and back of the system. This will reduce the possibility of the system being alarmed by the displayed merchandise. 4-1/2 Foot No Tag Zone 4-1/2 Foot No Tag Zone
Краткое содержание страницы № 12
ALARM HANDLING There are three reasons for the system to alarm: 1. The REAL alarm: The occurrence of a shoplifting attempt. 2. The ACCIDENTAL alarm: a) Personnel neglected to remove a tag at the point of sale. b) An electronic security access card has been carried into the store by a customer, or c) A previously purchased product, with an active tag, from another store using a similar system. 3. The PHANTOM alarm: The alarm sounds for no ap
Краткое содержание страницы № 13
TROUBLESHOOTING If a problem develops with the SP-1 system it is usually caused by common occurrences. The following is a basic troubleshooting guide to be used prior to contacting your supplier if the need arises. DO NOT MAKE ANY INTERNAL ADJUSTMENTS TO THE SYSTEM PRIOR TO CONTACTING YOUR SUPPLIER. NO DETECTION 1. Insure that the power supply is plugged into an AC with the proper voltage. 2. Feel the case of the power supply for warmth. Warmth indicates the pow
