Краткое содержание страницы № 1
DSM300 & DSM30
Digital Sounder
Module
Installation Manual
Document number: 87080-1
Date: November 2006
Краткое содержание страницы № 2
Trademarks and registered trademarks HSB, Raymarine and SeaTalk are registered trademarks of Raymarine plc. All other product names are trademarks or registered trademarks of their respective owners. Contents of this handbook ©Raymarine 2006
Краткое содержание страницы № 3
3 Contents Trademarks and registered trademarks ............................................ 2 Important Information .........................................................................................5 Intended Use .......................................................................................... 5 Safety Notices ...................................................................................... 5 EMC Conformance .................................................................
Краткое содержание страницы № 4
4 DSM300 and DSM30 Installation Manual 2.4 How to Contact Raymarine ...................................................................28 On the Internet .....................................................................................28 Customer Support ..........................................................................28 In the US ...............................................................................................28 Accessories and Parts ..................................
Краткое содержание страницы № 5
5 Important Information Raymarine DSM300 and DSM30 Digital Sounder Modules provide echo sounder 2 data that can be displayed on Raymarine E Series, C Series, and hsb PLUS (Pathfinder) Series display units. This manual contains important information for installing and maintaining your Digital Sounder Module. Raymarine’s Technical Services representatives or your local dealer will be available to answer any questions you may have. Instructions on how to operate the fishfinder application can
Краткое содержание страницы № 6
6 DSM300 and DSM30 Installation Manual EMC Conformance All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. The design and manufacture of Raymarine equipment and accessories conform to the appropriate Electromagnetic Compatibility (EMC) standards, but correct installation is required to ensure that performance is not compromised. Declaration of Conformity Raymarine plc declare that the DSM300 and DSM30 Digital Soun
Краткое содержание страницы № 7
7 Chapter 1: DSM Installation 1.1 Introduction This chapter provides details for mounting the DSM300 and DSM30 and connecting to the display. For the system to display depth, water temperature and speed, you must install the transducer type(s) capable of transmitting the appropriate data. Planning the Installation Before you install your system, plan the installation, considering: Location of the sounder module, as described in Section 1.3 Cable Runs, as described in Section 1.5 Correct
Краткое содержание страницы № 8
8 DSM300 and DSM30 Installation Manual The equipment is supplied from a separate battery from that used for engine start. Voltage drops below 10 V and starter motor transients can cause the equipment to reset. This will not damage the equipment, but may cause the loss of some informa- tion and may change the operating mode. Raymarine specified cables are used. Cutting and rejoining these cables can compromise EMC performance and must be avoided unless doing so is detailed in the install
Краткое содержание страницы № 9
Chapter 1: DSM Installation 9 1.2 Unpacking and Inspecting the Components Unpack your system carefully, to prevent damage to the equipment. Save the carton and packing, in case you need to return the unit for service. Check that you have all the correct system components: DSM300 Power Cable, 3m part no. R69053 C Series Network Cable, 3m part no. E65010 DSM300 Digital Sounder Module, part no. E63069 2 DSM300 hsb adapter, 4-pin to 3-pin DSM300 & DSM30 Operation Installation Man
Краткое содержание страницы № 10
10 DSM300 and DSM30 Installation Manual A 3m-long cable is included for connecting your sounder module to a C Series or 2 hsb PLUS (Pathfinder) Series display. Longer cables and connection cables for other types of systems must be purchased separately. 2 Note: C Series displays have 4-pin connectors while the older hsb PLUS Series displays have a 3-pin configuration. This requires that you use a 4-pin to 3-pin adapter (Raymarine 2 part number R69081) when connecting a sounder module to an
Краткое содержание страницы № 11
Chapter 1: DSM Installation 11 Interference: The selected location should be far enough away from devices that may cause interference, such as motors, generators, and radio transmitter/receivers. (See the EMC guidelines earlier in this chapter.) Magnetic compass: Mount the unit at least 3 ft (1 m) away from a magnetic compass. Cable runs: The unit must be located near a DC power source. The power cable supplied is 10 ft (3 m). Environment: Provide good ventilation to prevent overheat
Краткое содержание страницы № 12
Vertical Vertical 12 DSM300 and DSM30 Installation Manual To mount the DSM: 1. Hold the module in the location where you want to mount it, making sure it is perpendicular to the deck. 2. Mark the location of the four key holes onto the mounting surface. x4 D7479-1 3. Drill a 9/64" pilot hole at each of the marked locations. x4 D7538-1
Краткое содержание страницы № 13
Chapter 1: DSM Installation 13 Note: For fiberglass with a gelcoat surface, you should overdrill the surface to prevent the gelcoat from chipping when driving in the screw. Before drilling the pilot hole, hand drill the marked location with an oversized bit and countersink to approximately 3/8" diame- ter. 4. Drive the supplied #8 screws into the pilot holes. Screw them in about half way. 5. Mount the module to the surface, slipping the screw heads through the four key holes. 6. Press the mo
Краткое содержание страницы № 14
14 DSM300 and DSM30 Installation Manual 1.5 Cable Runs Consider the following before installing the system cables: You will need to attach power, transducer, and display cables. All cables should be adequately secured, protected from physical damage, and protected from exposure to heat. Avoid running cables through bilges or doorways, or close to moving or hot objects. Avoid sharp bends. Use a watertight feed-through wherever a cable passes through an exposed bulkhead or deckhead.
Краткое содержание страницы № 15
Chapter 1: DSM Installation 15 Transducer Connection A 30 ft (10 m) cable is supplied with the transducer. This cable has a connector plug (with an outer nut that you must attach) at one end for attaching to the “T/D” connector on the sounder module. Optional extension cables are available. CAUTION: Do Not Cut or Splice the Transducer Cable • There is high voltage on the transducer cable. Splicing could create a safety hazard. Cutting the transducer cable severely reduces sonar performan
Краткое содержание страницы № 16
16 DSM300 and DSM30 Installation Manual 1 2 D6162-1 3 Pin No. Function Color 1 Battery positive Red 2 Battery negative Black 3 Shield (drain wire) No insulation There is no power switch on the DSM. The unit turns on when the power cord is attached to boat’s power and plugged into the POWER connector on the connector panel. Note: You should locate the DSM so that the power cord can be easily removed, if necessary. If the sounder is placed in a difficult-to-reach location, Raymari
Краткое содержание страницы № 17
Chapter 1: DSM Installation 17 Sounder Module C Series Display Unit Power Supply Transducer Power Connections with a C Series Display 2 Sounder Module Power Supply hsb PLUS Series Display Unit Transducer 2 Power Connections with an hsb PLUS Series Display D9602-1 D9601-1
Краткое содержание страницы № 18
hs SeaTalk Cable 18 DSM300 and DSM30 Installation Manual Ground Connection It is important that an effective RF ground is connected to the system. A single ground point should be used for all equipment. You can ground the sounder module by connecting the drain wire (shield) of the Power Input cable to the boat’s RF ground. If you need to extend the wire, the extension wire should be an 8 mm braid or AWG 10 multi-stranded cable. If your boat does not have an RF system, connect the drain wi
Краткое содержание страницы № 19
Chapter 1: DSM Installation 19 hs When used in a multiple display system, connect the DSM to the SeaTalk Network Switch. hs SeaTalk Network Switch DSM E55058 E Series Display E Series Display hs SeaTalk Cable hs SeaTalk Cable hs SeaTalk Cable Configuring an E Series System - Multiple Displays Configuring C Series Displays The C Series system uses cables with a round 4-pin twist-lock network connector. A 3m-long C Series cable is included with your sounder module and is also
Краткое содержание страницы № 20
20 DSM300 and DSM30 Installation Manual 2 Configuring hsb PLUS (Pathfinder) Series Displays 2 hsb PLUS network cables have a triangular 3-pin connector on both ends. When 2 using the DSM with an hsb PLUS Series display, connect the supplied 4-pin to 2 3-pin hsb adapter between the sounder module and the network cable. 2 The hsb system must be terminated at both ends of the network. If a PLUS Series display is the last device on the network, an inline terminator is installed on the cable wher
