Краткое содержание страницы № 1
R
E
B
E
W
Owners Guide
DANGER
If you smell gas:
1. Shut off gas to the appliance.
Liquid Propane Gas
2. Extinguish any open flames.
3. Open lid
4. If odor continues, keep away from the
appliance and immediately call your gas
®®
supplier or your fire department.
Leaking gas may cause a fire or explosion
which can cause serious bodily injury or
death, or damage to property.
WARNING
1. Do not store spare liquid propane
cylinder within 10 feet (3m) of this
appliance.
2. Do not store or use gasol
Краткое содержание страницы № 2
DANGER Failure to follow the Dangers, Warnings and Cautions contained in this Owner’s Manual may result in serious bodily injury or death, or in a fire or an explosion causing damage to property. WARNINGS Do not store a spare or disconnected liquid propane cylinder under or near this barbecue. Improper assembly may be dangerous. Please carefully follow the assembly instructions in this manual. After a period of storage, and/or nonuse, the Weber Gas Barbecue should be checked for gas le
Краткое содержание страницы № 3
Warranty Weber-Stephen Products Co. (Weber) hereby warrants There are no other express warrants except as set forth to the ORIGINAL PURCHASER of this Weber Gas Grill herein and any applicable implied warranties of that it will be free of defects in material and merchantability and fitness are limited in duration to the workmanship from the date of purchase as follows: period of coverage of this express written Limited Warranty. Some regions do not allow limitation on how Aluminum Castings, lifet
Краткое содержание страницы № 4
Contents Danger & Warnings ................................ A-2 Warranty ................................................. A-3 General Instructions ............................... A-5 Exploded View ........................................ A-6 Parts List ................................................ A-9 Assembly Instructions ............................ B-1 Installing Features .................................. C-1 Operating ............................................... D-1 Lighting.........
Краткое содержание страницы № 5
Storage General Instructions • The gas must be turned OFF at the LP cylinder Your Weber Gas Barbecue is a portable outdoor when the Weber Gas Barbecue is not in use. cooking appliance. With the Weber Gas Barbecue you • When the Weber Gas Barbecue is stored indoors, can grill, barbecue, roast and bake with results that are the gas supply must be disconnected and the LP difficult to duplicate with indoor kitchen appliances. cylinder stored outdoors in a well-ventilated space. The closed lid and Fl
Краткое содержание страницы № 6
Genesis Silver-C LP 032301 1 2 27 3 28 4 29 5 6 30 7 31 32 33 8 9 34 35 36 10 37 11 12 38 13 39 40 14 41 42 15 43 44 45 16 17 46 33 18 47 19 20 48 21 49 22 50 23 51 24 52 53 25 26 54 55 A-6
Краткое содержание страницы № 7
1. Hinge Pin 29. Right Endcap 2. Left Endcap 30. Burner Control Knobs 3. Shroud 31. Control Panel 4. Handle 32. Ignitor Button ™ 5. Warm-Up Basket 33. Control Panel Hardware 6. Warming Rack 34. Side Burner 7. Cooking Grates 35. Crossover tube ® 8. Flavorizer Bars 36. Front and Back Burners 9. Cooking Box 37. Center Burner 10. 1/4-20 keps nut 38. Manifold Support Bracket 11. Slide Out Bottom Tray 39. Manifold, Hose and regulator (assembled) 12. Catch pan holder 40. Manifold Hardware 13. Catch pan
Краткое содержание страницы № 8
© 2001 Weber-Stephen Products Co., Weber, the silhouette, and the kettle configuration are registered trademarks ® of Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL, 60067-6266, U.S.A. This product is covered by one or more United States patents and patents in other nations globally. Printed in the U.S.A. A-8
Краткое содержание страницы № 9
® ® ® ® ® You will need: Left Frame - 1 Screwdriver Phillips screwdriver Right Frame - 1 Hammer Wheel Frame - 1 7/16 open-end or an adjustable wrench Pliers Caster Frame - 1 Block of wood Frame Connectors - 2 Lid - 1 Sideburner - 1 Work Surface - 1 Cooking Box - 1 Swing-Up Work Surface - 1 Hinge Rod - 1 Left Trim Piece - 1 Cooking grates - 2 Right Trim Piece - 1 Bottom Shelf - 1 Control panel - 1 A-9
Краткое содержание страницы № 10
Warming Rack - 1 Burner Control Knobs - 3 Warm-Up Basket - 1 Hinge Pins (1/4 x 1 1/2 inch clevis pin) - 2 Flavorizer Bars - 5 2 inch bolts (1/4 x 20 x 2 inch bolts) - 5 Cylinder Panel - 1 1 3/4 inch bolts (1/4 x 20 x 1 3/4 inch bolts) - 2 Front Panel - 1 1/2 inch bolts (1/4 x 20 x 1/2 inch bolts) - 8 Back Panel - 1 Bottom tray - 1 Keps Nut (1/4 x 20 Keps Nut) - 1 Wing Nut (1/4 x 20 Wing Nut) - 2 Catch Pan Holder - 1 Nylon Washers - 17 Catch-Pan - 1 Hair Pin Cotter - 2 Disposable Drip Pans - 2 Hu
Краткое содержание страницы № 11
R E B E W Assembly Instructions Assemble wheel frame Assemble frame You will need: axle rod, two wheel hubcaps, two You will need: left frame, right frame, two 1/2 inch wheels, wheel frame, hammer and a block of wood. bolts, two nylon washers and a 7/16 inch or adjustable Place one end of the axle rod on the block of wood (or wrench. other protected surface). Tap one hubcap onto the end Note - Work on carpeted area (on grass or one of the of the axle rod. Slide one wheel onto the axle, WEBER box
Краткое содержание страницы № 12
Continue frame assembly Add back panel You will need: caster frame and wheel frame. You will need: frame assembly, back panel, two 1/2 Place the caster frame onto the tabs of the left frame, inch bolts, two nylon washers, and a 7/16 or adjustable so that the swing table locking bracket (1) is to the rear. spanner. Place the wheel frame onto the tabs of the right frame, Place the back panel against the inside frame so that the swing table locking bracket is to the rear assembly as shown in illust
Краткое содержание страницы № 13
Insert casters You will need: frame assembly and two casters. Slide the cooking box (assembly) to the left within the Push the casters firmly into the inserts in the ends of frame assembly. Add the nylon washer to the bolt. the caster frame. Insert the bolt through the frame and cooking box with the head of the bolt outside the box. Add the keps nut. Tighten by holding the bolt with pliers while you tighten the nut with a wrench. Add cooking box (assembly) You will need: frame assembly, cooking
Краткое содержание страницы № 14
Install manifold brackets Slide the cylinder panel up until notch at bottom of The manifold brackets(2) are already in place on the panel fits over the cross brace(1). Add nylon washer to manifold between the valves. bolt and insert through the hole in the wheel frame at Place your hand underneath the manifold. Lift the the bottom right of the cylinder panel, make sure that manifold and cooking box slightly and hook the the bolt slips through the hole in the cylinder panel. manifold bracket(2)
Краткое содержание страницы № 15
Install igniter Install the slide out bottom tray Note - The igniter wires are already attached to the You will need: the slide out bottom tray(1), catch pan Gas Catcher Ignition Chamber and the igniter. This holder(2), catch pan and one disposable drip pan. was done to factory test the ignition system. The igniter lock nut is on the igniter. 1) Loosen the igniter lock nut. 2) Insert the top of the igniter up through the large part of the keyhole in the frame brace. Slide the igniter into the sm
Краткое содержание страницы № 16
Install Lid Install control panel and burner control knobs You will need: lid, two hair pin cotters(1) and two hinge You will need: control panel, two Phillips screws/ pins(2). washers, a Phillips screwdriver, and burner control Place lid on top of the cooking box. Align the hinges at knobs. the rear of the barbecue. Insert hinge pins through the 1) Set the control panel in place over both frame hinges from the outside. Insert hair pin cotters into the braces. Hold the Crossover Ignition button
Краткое содержание страницы № 17
Installing Features Install the right trim piece with tool holders Install the left end trim piece and swing-up work You will need: Right trim piece with tool holders surface Push the Right trim piece into the frame as shown(1), You will need: End trim piece, swing-up work surface, making sure that the tabs on the underside of the trim swing-up work surface rod, two 1/2 inch bolts, two piece are snapped into the slots in the frame.(2) nylon washers and a wrench 1.) Start the left end trim piece
Краткое содержание страницы № 18
3.) Insert one end of the swing-up work surface rod 5.) Add a washer to each bolt and insert it through the into the hole in the frame. hole in the frame and the hole in the trim piece on both sides. Tighten with a wrench. To raise swing-up work surface: Lift table all the way up and slide it to the right, then lower table until you feel it lock in the up position. To lower swing-up work surface: Lift table up until it disengages and slide it to the left. Then lower it all the 4.) While holding
Краткое содержание страницы № 19
Install the work surface Set the side burner in place in the frame. The side You will need: work surface. burner locking clip on the right should latch under the Place the work surface, so that the front and back right trim piece. edges fit over the frame, in the area between the left trim piece and the cooking box as shown. Do not use the work surface as a cutting board. (1) Tilt the side burner slightly, toward the control panel. (1) Make sure that the tabs on the side table are to the Latch t
Краткое содержание страницы № 20
Connect the side burner hose as follows: Set the cooking grates onto the ledges in the cooking 1) Slide back the collar of the quick disconnect box with the rounded sides up. on the manifold. 2) Push the male fitting of the side burner hose into the quick disconnect, and maintain pressure. Slide the collar closed. (1) Installing the warming rack You will need: warming rack. Set the warming rack into the slots at the rear of the cooking box. (2) Quick disconnect will be engaged. Check to be sure
