Краткое содержание страницы № 1
Gas Barbecue
Use, Care & Assembly Manual
With Grill Lighting Instructions
5600 LP Gas Series
5610 Natural Gas Series
ASSEMBLER/INSTALLER:
Leave these instructions with the consumer.
CONSUMER/USER:
Read all instructions and keep in a safe place for future reference.
www.coleman.com For Outdoor Use Only
IIM MP PO OR RT TA AN NT T
Read this manual carefully before assembling,
using or servicing this grill. Keep this manual for
future reference. If you have questions about
assembly, operation, servi
Краткое содержание страницы № 2
Contents WARNING General Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IF YOU SMELL GAS: General Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1. Shut off gas to the appliance. Electrical Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Extinguish any open flame. Fuel Connections Other Than Portable L.P. Cylinders . . . . .
Краткое содержание страницы № 3
3 1 2 General Safety Information cont. 4 7 36" 8 5 6 General Installation • Installation must conform with local codes or, in the absence of local 9 codes, with either the National Fuel Gas Code, ANSI Z223.1 (USA), CAN/CGA-B149.1, Natural Gas Installation Code or CAN/CGA-B149.2, Clear Propane Installation Code (Canada). To check local codes, see your local L.P. gas dealer or natural gas 36" company listed in the Yellow Pages for recommended installation pro- (90cm) cedures and regulations.
Краткое содержание страницы № 4
Electrical Attachments Fuel Connections Other Than Portable L.P. Cylinders cont. When using an electric attachment with grill, follow specification and warning statements accompanying the attachment. THE PIPING SYSTEM MUST BE INSTALLED IN ACCORDANCE IMPORTANT: If using an external electrical source, the installed WITH NATIONAL FUEL GAS CODE IN THE USA, INCLUDING: appliance must be electrically grounded according to local codes or, in the absence of local codes, with the National Electrical 1. T
Краткое содержание страницы № 5
L.P. Gas Cylinder L.P. Gas Cylinder cont. DANGER CAUTION • DO NOT insert any foreign objects into the valve outlet. Have the gas dealer weigh cylinder after filling to ensure that You may damage the valve. A damaged valve can cause the cylinder is not overfilled. a leak, which could result in explosion, fire, severe per- sonal injury or death. Hose and Regulator WARNING The Type 1 connection system has the following features: • Cylinders must be stored outdoors out of the reach of 1.The system
Краткое содержание страницы № 6
Filling and Purging Type 1 Transporting the Cylinder cont. L.P. Gas Cylinders cont. WARNING 13 Handle a full cylinder with care. Gas is under high pressure. CGA-510 POL DANGER • NEVER store a spare L.P. gas supply cylinder under the grill body or inside grill enclosure or in the vicinity of any heat producing appliance. (Fig. 12) • NEVER fill the cylinder beyond 80% full. Failure to follow this information exactly could result in an explosion and/or fire causing death or serious injury. 12 P
Краткое содержание страницы № 7
Assembly/Set up ■ Remove components from package. Rotisserie Hardware Blister Pack Rear Trim Plate Firebox Warming Racks Left Fryer Assembly Grates Right Side Table Fryer Grease Cart Spacer Pan Fryer Cart Spacer Heat Shield Cylinder Support Center Left Right Burner Heat Tents™ Base Base Base Thermometer Wire Mesh 9-Volt Basket Battery Reservoir Grease Pan Left Right Panel Panel Rear Rear Panel Panel Grease Grease Cup Cups Supports Tool Hook Door Left Door Magnets Right Door Handles Door Non-Lock
Краткое содержание страницы № 8
NOTE: Use a large piece of cardboard or a ground cloth to protect the painted finish on the grill. NOTE: The base pieces are assembled up-side- Step down in this step. 1 1-A Right Base Hardware shown actual size (TN) M6 x 15mm Screw (8) Qty. Grill Label TN Center Base TN (x8) Left Base 1-A. Arrange the three base pieces on the ground as shown. Assemble the Right Base and the Left Base to the Center Base using two screws (TN) in each corner. Note: Arrange the Center Base so the Grill Label is
Краткое содержание страницы № 9
Carefully turn the assembly Assemble the Right Side Right-Side-Up. Panel. Engage the Locking Assemble the Left Side Step Step Casters to prevent Panel. 2 3 movement during the rest of the assembly process. 2-A. Assemble the Cylinder 2-A Retaining Bolt to the 3-A. Assemble the Hardware shown actual size Cylinder Support. Right Side Panel and the Left Side Panel to the Base using four Screws (TN) (TN). M6 x 15mm Screw (4) Qty. Tighten all fasten- ers. 2-B. Assemble the Cylinder Hardware shown
Краткое содержание страницы № 10
Assemble two Cart Spacers Hardware shown actual size to the Grill Cart. Step 4 (TN) M6 x 15mm Screw (8) Qty. 4-A. Assemble two Cart Spacers between 4-A the Left and Right Panels using eight Cart TN (x8) Screws (TN). Spacer NOTE: The Cart Spacers are identical. Assemble one vertically and one hori- zontally. Tighten all fasteners. Cart Spacer View of Grill from Rear 4-B. View of Cart Spacers properly 4-B assembled. Cart Spacers View of Grill from Rear 10 Back
Краткое содержание страницы № 11
Front Front Install Rear Panels. Install Door Magnets. Hardware shown actual size Step Step 5 6 (TN) M6 x 15mm Screw Hardware shown actual size (8) Qty. 5-A TN (x8) (UO) (TN) M6 Locking Hex Nut M6 x 15mm Screw (4) Qty. (4) Qty. Rear 6-A Panel Door Magnet Rear Panel UO (x2) TN (x2) 5-A. Assemble two Rear Panels to the cart assem- 6-A. Assemble one Door Magnet to the Right Panel with two Screws (TN) and two Locking Hex Nuts (UO). bly using eight Screws (TN). 6-B NOTE: The Rear Panels 5-B are id
Краткое содержание страницы № 12
Front Assemble Firebox to the Grill Cart. NOTE: A second person is Step needed when aligning the 7 Firebox to the Grill Cart. 7-A Firebox Grill Cart 7-A. Carefully place the Firebox onto the Cart Assembly. Do not damage the Electrical Wires (see Fig. 7-B and 7-C). The Electrical Wires must be routed through the openings near the front and back of the Firebox. 7-B 7-C Do Not Pinch Electrical Wires 12
Краткое содержание страницы № 13
Fasten the Firebox to the Hardware shown actual size Grill Cart. NOTE: In Fig. 8-A and 8-B, the Step Cart Spacer is not illustrated. 8 (TN) (DY) M6 x 15mm Screw M6 Flat Washer (4) Qty. (4) Qty. 8-A. Lower the Firebox until it is supported by 8-A Firebox the flanges on the Right and Left Side Panels. LOOSELY fasten the Firebox to the Right Side Panel with two Flat Washers (DY) and two Screws (TN) as shown in Fig. 8-A. NOTE: You will tighten these screws LATER (during Step 8-B), after the left
Краткое содержание страницы № 14
NOTE: The Grill Lids should Hardware shown actual size be opened for Step 9. Assemble Right Side Table to Step the Grill. 9 (TN) M6 x 15mm Screw (4) Qty. 9-A. Raise the Grill Lids. 9-A Right Side Firebox Place the Right Side Table against the Table Firebox and on top of the Right Rear Panel. Right Rear Panel 9-C Flange 9-B TN (x4) 9-B. LOOSELY install four Screws (TN) upward through the Flange of the Right Rear Panel into the Right Side Table. NOTE: You will tighten these screws LATER (durin
Краткое содержание страницы № 15
Assemble Right Side Table Hardware shown actual size to the Grill (continued). Step 10 (TN) (DY) M6 x 15mm Screw M6 Flat Washer (4) Qty. (2) Qty. 10-A. LOOSELY assemble two additional 10-A Screws (TN) and two Flat Washers (DY) through the Firebox into the Right Side Table at the rear of the grill. 10-B TN (x2) DY (x2) View of Grill from Rear 10-C. Assemble two additional Screws (TN) 10-C through the Right Side Table into the Firebox at the front of the grill. Tighten all fasteners. 10-D TN (x2
Краткое содержание страницы № 16
NOTE: The Grill Lids must Hardware shown actual size be opened for Step 11. Assemble Left Fryer Step Assembly to the Grill. 11 (TN) M6 x 15mm Screw (1) Qty. 11-A. Raise the Grill Lids. 11-A Left Fryer Place the Left Fryer Assembly against Assembly the Firebox and on top of the Left Rear Panel. 11-C Left Rear Panel Flange 11-B TN 11-B. Align three studs from Left Fryer Assembly with slots in flange of the Left Rear Panel. LOOSELY install one Screw (TN) upward through the Flange of the Left Re
Краткое содержание страницы № 17
Assemble Left Fryer Hardware shown actual size Assembly to the Grill (continued). Step 12 (TN) (DY) M6 x 15mm Screw M6 Flat Washer (4) Qty. (2) Qty. 12-A. LOOSELY assemble two additional 12-A Screws (TN) and two Flatwashers (DY) through the Firebox into the Left Fryer Assembly at the rear of the grill. 12-B TN (x2) DY (x2) View of Grill from Rear 12-C. Assemble two additional Screws (TN) 12-C through the Left Fryer Assembly into the Firebox at the front of the grill. Tighten all fasteners. 12
Краткое содержание страницы № 18
Assemble the Fuel Hose Fitting from the Grill to the 13-B Fryer Assembly. Step Collar on 13 the Quick Coupler 13-A Male Hose Fitting 13-B. Retract the Collar on the Quick Coupler before insert- ing the Male Hose Fitting. Fully insert the Male Hose Fitting into the Quick Coupler. Release the Collar to lock the connection. Fuel Hose from Fryer Assembly 13-A. Assemble the Fuel Hose Fitting from the Grill to the Fryer Assembly. 13-C Caution: For leak-check WARNING: procedure, read and follow
Краткое содержание страницы № 19
Assemble the Electrode Wire to the Electrode Tip on the Side Fryer. Step Assemble the Grease Pan 14 below the Fryer Burner. 14-A Route the Electrode Wire through the slot in the Fryer Panel. Electrode Wire Electrode Tip Fryer Left Panel Side Panel 14-A. Attach the Electrode Wire to the Electrode Tip on the Side Fryer. 14-B Hooks Fryer Grease Pan 14-B. Attach Fryer Grease Pan using four hooks located below the Fryer Burner. NOTE: To attach the Fryer Grease Pan, raise the Pan slightly above the
Краткое содержание страницы № 20
Assemble Front Fryer Heat Shield. Step 15 15-A Electrode Wire Engage Tabs into Rectangle Holes Fryer Heat Shield 15-A. Assemble Fryer Heat Shield. NOTE: Place the Fryer Heat Shield between the Fryer Panel and the Flexible Fuel Hose. Do not pinch Electrode Wire. Engage the two tabs on the Heat Shield downward into the rectangle holes. 15-B Fryer Heat Shield 15-B. View showing the Fryer Heat Shield properly installed. 20
