Краткое содержание страницы № 1
Owner's Manual/Manual Del Propietario
I:RRFTSMR
315MM= GARAGE DOOR OPENER
ABRIDOR DE PUERTA DE COCHERA 315MN_,
For Residential Use Only/Solo para uso residencial
Model/Modelo 139.53918D
m
G3
m
Z_
O
Read and follow all safety rules Leer y seguir todas las reglas de
and operating instructions before seguridad y las instrucciones de
first use of this product. operacion antes de usar este
producto por primera vez.
Guardar este manual cerca de la
Fasten the manual near the garage
door after installat
Краткое содержание страницы № 2
TABLE OF CONTENTS Adjustment 27-29 Introduction 2.7 Program the travel limits ...................... 27 Safety symbol review and signal word review ......... 2 Setting the force ............................. 28 Preparing your garage door ....................... 3 Test the safety reversal system ................. 29 Tools needed .................................. 3 Test The Protector System ®(safety sensors) ...... 29 Planning .................................... 4-5 Carton inventory ............
Краткое содержание страницы № 3
Preparing your garage door Before you begin: To prevent possible SERIOUSINJURYOR DEATH: • Disable locks. • ALWAYScall a trained door systems technician if garage • Remove any ropes connected to garage door. door binds, sticks, or is out of balance An unbalanced • Complete the following test to make sure your garage garagedoor may not reversewhen required door is balanced and is not sticking or binding: • NEVERtry to loosen, move or adjust garagedoor, door springs, cables, pulleys, brackets or th
Краткое содержание страницы № 4
Do you have an access door in addition to the garage Planning door? If not, Model 139.53702 Emergency Key Identify the type and height of your garage door. Survey Release is required. See Accessories page. your garage area to see if any of the conditions below Look at the garage door where it meets the floor. Any apply to your installation. Additional materials may be gap between the floor and the bottom of the door must required. You may find it helpful to refer back to this page not exceed 1/4
Краткое содержание страницы № 5
Planning (Continued) ONE-PIECE DOOR INSTALLATIONS Without a properly working safety reversal system, persons (particularly small children) could be SERIOUSLYINJURED • Generally, a one-piece door does not require or KILLEDby a closing garagedoor. reinforcement. If your door is lightweight, refer to the • The gap betweenthe bottom of the garage door and the information relating to sectional doors in Installation floor MUST NOTexceed 1/4" (6 mm). Otherwise,the safety Step 12. reversal system may no
Краткое содержание страницы № 6
Carton Inventory Your garage door opener is packaged in one carton material. Parts may be stuck in the foam. Hardware for which contains the motor unit and all parts illustrated assembly and installation is shown on the next page. below. Accessories will depend on the model purchased. Save the carton and packing material until installation If anything is missing, carefully check the packing and adjustment is complete. ; Z:z :b :::?b- -_ i a! ,% ._ ,,, SECURITY÷ ® 3-Function Remote Control (2) Ba
Краткое содержание страницы № 7
Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures. ASSEMB_ HARDWARE © Spring/Trolley Nut (1) Lock Nut Lock Washer Nut 1/4"-20 (2) 3/8" (1) 3/8" (1) i Bolt 1/4"-20x 1-3/4" ( 1) S5 Master Idler Bolt (1) Link (2) F Trolley Threaded Shaft (1) INSTALLATION HARDWARE O © Handle Carriage Bolt Ring Nut 5/16"-18 (6) Wing Nut 1/4"-20xl/2" (2) Fastener (3) 1/4"-20 (2) llllllll[_ © Hex Bolt Insulated Lag Screw 5/16"-9xl -5/8" (2) 5/16"-18x7/8" (4)
Краткое содержание страницы № 8
ASSEMBLY STEP 1 Assemble the Rail and Install the Trolley To prevent INJURYfrom pinching, keep hands and fingers awayfrom the joints while assembling the rail. To avoid installation difficulties, do not run the garage door opener until instructed to do so. The front rail has a cut out "window"at the door end (see 3. Place the motor unit on packing material to protect the illustration). The hole above this window is larger on cover, and rest the back end of the rail on top. For the top of the rai
Краткое содержание страницы № 9
ASSEMBLY STEP 2 Fasten the Rail to the Motor Unit To avoid SERIOUSdamageto garagedoor opener, use ONLY those bolts/fasteners mounted in the top of the opener. • Insert a 1/4"-20xl -3/4 bolt into the cover protection bolt hole on the back end of the rail as shown. Tighten securely with a 1/4"-20 lock nut. Do NOTovertighten. • Remove the two bolts from the top of the motor unit. • Place the "U" bracket, flat side down, on the motor unit and align the bracket holes with the bolt holes. Fasten with
Краткое содержание страницы № 10
ASSEMBLY STEP 4 Install the Belt and Attach the Belt To avoid possible SERIOUSINJURYto fingers from moving Cap Retainer garage door opener: • ALWAYSkeep hand clear of belt pulley while operating 1. Pull the belt around the idler pulley and toward the opener• trolley. The ribbed side must contact the pulley, • Securelyattach belt pulley cover BEFOREoperating. 2. Hook the trolley connector into the retaining slot on the trolley as shown. 3. With the trolley against the screwdriver, dispense the re
Краткое содержание страницы № 11
ASSEMBLY STEP 5 Set the Tension • Insert a screwdriver tip into one of the nut ring slots and brace it firmly against the trolley. S j • Place a 7/16" open end wrench on the square end. Rotate the nut about 1/4 turn until the spring releases and snaps the nut ring against the trolley. This sets the spring to optimum belt tension. You have now finished assembling your garage door opener. Please read the following warnings before proceeding to the installation section. Trolley Square End Nut Rin(
Краткое содержание страницы № 12
INSTALLATION STEP 1 Determine the Header Bracket Location Ceiling q CEILINGOPTIONALHEADERFORMOUNTBRACKET Unfinished 2x4_ Header Wall Vertical Centerline of Garage Door To prevent possible SERIOUSINJURYor DEATH: 2x4 • Header bracket MUST be RIGIDLYfastened to structural Structural /' Supports support on headerwall or ceiling, otherwise garagedoor might not reversewhen required. DO NOTinstall header bracket over drywall. • Concreteanchors MUST be used if mounting header bracket or 2x4 into masonry
Краткое содержание страницы № 13
Wall Mount INSTALLATION STEP 2 Install the Header Bracket You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided). Optional Mounting Holes WALL HEADER BRACKET INSTALLATION • Center the bracket on the vertical centerline with the Vertical bottom edge of the bracket on th
Краткое содержание страницы № 14
INSTALLATION STEP 3 Attach the Rail to the Header Bracket NOTE: (Optional) With some existing installations, you may re-use the old header bracket with the two plastic spacers included in the hardware bag. Place the spacers inside the bracket on each side of the rail, as illustrated. • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way, you will need help. Have someone hold the opener securely on a t
Краткое содержание страницы № 15
INSTALLATION STEP 4 Position the Opener To prevent damageto garage door, rest garage door opener rail on 2x4 placed on top section of door. Follow instructions which apply to your door type as illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid flat is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 la
Краткое содержание страницы № 16
INSTALLATION STEP 5 Hang the Opener To avoid possible SERIOUSINJURYfrom a falling garage door opener, fasten it SECURELY to structural supports of Three representative installations are shown. Yours may the garage. Concreteanchors MUST be used if installing any be different. Hanging brackets should be angled brackets into masonry. (Figure 1) to provide rigid support. On finished ceilings (Figures 2 and 3), attach a sturdy metal bracket to structural supports before installing the opener. This br
Краткое содержание страницы № 17
INSTALLATION STEP 6 Install the Control Console To prevent possible SERIOUSINJURYor DEATHfrom electrocution: Locate control console within sight of door, at a minimum • Disconnect ALL electric and battery power BEFORE height of 5 feet (1.5 m) where small children cannot performing ANY service or maintenance. reach, away from moving parts of door and door • Connect ONLYto 24 VOLTlow voltage wires. hardware. If installing into drywall, drill 5/32" holes and To prevent possible SERIOUSINJURYor DEAT
Краткое содержание страницы № 18
INSTALLATION STEP 7 Install the Battery Battery • Make sure motor unit is unplugged. • Using a Phillips head screwdriver, remove the battery cover on the motor unit. • Partially insert battery into motor unit with terminals facing out. • Connect the red (+) and black (-) wires from motor unit to corresponding terminals on battery. • Replace battery cover. INSTALLATION STEP 8 Install the Lights To prevent possible OVERHEATING of the endpanel or light socket: • Press the release tabs on both sides
Краткое содержание страницы № 19
INSTALLATION STEP 10 Electrical Requirements To prevent possible SERIOUSINJURYor DEATHfrom electrocution or fire: To avoid installation difficulties, do not run the • Disconnect ALL electric and battery power BEFORE opener at this time. performing ANY service or maintenance. To reduce the risk of electric shock, your garage door • Garagedoor installation and wiring MUSTbe in compliance opener has a grounding type plug with a third grounding with ALL local electrical and building codes. pin. This
Краткое содержание страницы № 20
INSTALLATION STEP 1 1 Install The Protector System ® Be sure power is NOTconnected to the garagedoor opener (Safety Sensors) BEFOREinstalling the safety reversingsensor. To prevent SERIOUSINJURYor DEATHfrom a closing The safety reversing sensor must be connected and garage door: aligned correctly before the garage door opener will • Correctly connect and align the safety reversing sensor. move in the down direction. This required safety device MUST NOTbe disabled. IMPORTANT INFORMATION ABOUTTHE
