Краткое содержание страницы № 1
The Chamberlain Group, Inc.
845 Larch Avenue
Elmhurst, Illinois 60126-1196
www.liftmaster.com
®
GARAGE DOOR OPENER
Model 2595 3/4 HP
For Residential Use
Install on Sectional Doors ONLY
THIS OPERATOR IS INTENDED FOR USE ONLY WITH I-BEAM RAILS.
Owner’s Manual
■ Please read this manual and the enclosed safety materials carefully!
■ Fasten the manual near the garage door after installation.
®
■ The door WILL NOT CLOSE unless the Protector System is connected and
properly aligned.
■ Periodic checks o
Краткое содержание страницы № 2
TABLE OF CONTENTS Introduction Pages 2-5 Adjustment Pages 20-22 Safety symbol and signal word review ........................2 Adjust the travel limits ...............................................20 Preparing your garage door ........................................3 Adjust the force .........................................................21 Tools needed...............................................................3 Test the safety reversal system.................................22 ® Planni
Краткое содержание страницы № 3
1 Preparing your garage door WARNING WARNING Before you begin: To prevent possible SERIOUS INJURY OR DEATH: • Disable locks. • ALWAYS call a trained door systems technician if CAUTION WARNING •Remove any ropes connected to garage door. garage door binds, sticks, or is out of balance. An unbalanced garage door may not reverse when • Complete the following test to make sure your required. garage door is balanced and is not sticking or binding: • NEVER try to loosen, move or adjust garage door, do
Краткое содержание страницы № 4
— — — — — — — — Planning WARNING WARNING Identify the type and height of your garage door. Without a properly working safety reversal system, Survey your garage area to see if any of the persons (particularly small children) could be conditions below apply to your installation. Additional CAUTION SERIOUSLY INJURED or KILLED by a closing garage WARNING materials may be required. You may find it helpful to door. refer back to this page and the accompanying • The gap between the bott
Краткое содержание страницы № 5
LOCK LIGHT Carton Inventory Your garage door opener is packaged in two cartons purchased. If anything is missing, carefully check the which contain the motor unit and all parts illustrated packing material. Parts may be stuck in the foam. below. Accessories will depend on the model Hardware for installation is also listed below. Chain Spreader Remote Control SECURITY✚ Transmitter Visor Clip 3-Channel Remote Control Door Bracket Motion Detecting Door Control Panel Safety Sensor Chain Bracket (2)
Краткое содержание страницы № 6
WARNING WARNING ASSEMBLY STEP 1 CAUTION WARNING Attach the Rail to the Motor Unit To avoid SERIOUS damage to opener, ONLY use bolts/fasteners, mounted in top of motor unit. To avoid installation difficulties, do not run the garage door opener until instructed to do so. Figure 1 Washered Bolt • Remove the bolt and lock nut from the top of the 5/16"-18x1/2" motor unit. Lock Nut • Place rail onto the bolt mounted on the motor unit and align the back hole with the hole in the top of the unit. • Fas
Краткое содержание страницы № 7
ASSEMBLY STEP 4 Lock Tighten the Chain Outer Nut Washer Inner Nut To Tighten Outer Nut • Spin the inner nut and lock washer down the threaded shaft, away from the trolley. To Tighten •To tighten the chain, turn outer nut in the direction Inner Nut shown. As you turn the nut, keep the chain from twisting. • When the chain is approximately 1/2" above the Trolley base of the rail at its midpoint, re-tighten the inner nut to secure the adjustment. Chain Sprocket noise can result if chain is either t
Краткое содержание страницы № 8
INSTALLATION STEP 1 Finished Vertical Ceiling Centerline Determine the Header Bracket Header Structural 2x4 Wall Location Supports WARNING WARNING To prevent possible SERIOUS INJURY or DEATH: • Header bracket MUST be RIGIDLY fastened to CAUTION WARNING structural support on header wall or ceiling, otherwise garage door might not reverse when required. DO NOT install header bracket over drywall. Vertical • Concrete anchors MUST be used if mounting header Centerline bracket or 2x4 into masonry. •
Краткое содержание страницы № 9
INSTALLATION STEP 2 Install the Header Bracket Wall Mounting Holes You can attach the header bracket either to the wall CEILING MOUNT ONLY above the garage door, or to the ceiling. Follow the The nail hole is for positioning only. instructions which will work best for your particular You must use lag screws UP requirements. Do not install the header bracket to mount the header bracket. over drywall. If installing into masonry, use concrete anchors (not provided). WALL HEADER BRACKET INSTALLATI
Краткое содержание страницы № 10
INSTALLATION STEP 3 Attach the Rail to the Header Header Wall Bracket Header Bracket •Position the opener on the garage floor below the Chain header bracket. Use packing material as a Pulley Bracket protective base. NOTE: If the door spring is in the Header way you’ll need help. Have someone hold the Bracket opener securely on a temporary support to allow Ring Fastener the rail to clear the spring. •Position the rail bracket against the header bracket. Clevis Pin 5/16"x2-3/4" • Align the bracke
Краткое содержание страницы № 11
INSTALLATION STEP 5 WARNING WARNING Hang the Opener To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural Two representative installations are shown. Yours CAUTION supports of the garage. Concrete anchors MUST be used WARNING may be different. Hanging brackets should be angled if installing any brackets into masonry. (Figure 1) to provide rigid support. On finished ceilings (Figure 2), attach a sturdy metal bracket to structural supports before inst
Краткое содержание страницы № 12
LOCK LIGHT LOCK LIGHT WARNING WARNING INSTALLATION STEP 6 CAUTION WARNING Install the Door Control To prevent possible SERIOUS INJURY or DEATH from electrocution: Locate door control within sight of the door at a • Be sure power is not connected BEFORE installing door minimum height of 5 feet where small children cannot control. reach, and away from moving parts of the door and • Connect ONLY to 24 VOLT low voltage wires. door hardware. The installation surface must be To prevent possible SERIO
Краткое содержание страницы № 13
NOTICE INSTALLATION STEP 7 100 Watt (Max) Standard Light Bulb Install the Lights • Press the release tabs on both sides of lens. Release Tab Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in each socket. The lights will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the lights will turn OFF. Lens •Reverse the procedure to close the lens. Hinge 100
Краткое содержание страницы № 14
INSTALLATION STEP 9 WARNING WARNING Electrical Requirements To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: To avoid installation difficulties, do not run the CAUTION WARNING • Be sure power is not connected to the opener, and opener at this time. disconnect power to circuit BEFORE removing cover to To reduce the risk of electric shock, your garage door establish permanent wiring connection. opener has a grounding type plug with a third • Garage door installation and wiri
Краткое содержание страницы № 15
INSTALLATION STEP 10 WARNING WARNING ® Install The Protector System • Be sure power is not connected to the garage door opener BEFORE installing the safety reversing sensor. The safety reversing sensor must be connected CAUTION WARNING • To prevent SERIOUS INJURY or DEATH from a closing and aligned correctly before the garage door garage door: opener will move in the down direction. – Correctly connect and align the safety reversing sensor. This required safety device MUST NOT be IMPORTANT INFOR
Краткое содержание страницы № 16
INSTALLING THE BRACKETS Figure 1 Be sure power to the opener is disconnected. DOOR TRACK MOUNT (RIGHT SIDE) Install and align the brackets so the sensors will face each other across the garage door, with the beam no Door higher than 6" above the floor. They may be installed Track in one of three ways, as follows. Lip Garage door track installation (preferred): Indicator • Slip the curved arms over the rounded edge of light each door track, with the curved arms facing the door. Snap into place a
Краткое содержание страницы № 17
MOUNTING AND WIRING THE SAFETY SENSORS Figure 4 • Slide a 1/4"-20x1/2" carriage bolt head into the slot Wing nut on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension (Figure 4). Carriage bolt • Finger tighten the wing nuts. 1/4"-20x1/2" Lens Run the wires from both sensors to the opener. Use insulated staples to secure wire to wall and ceiling. TROUBLESHOOTING THE SAFETY S
Краткое содержание страницы № 18
WARNING WARNING CAUTION WARNING INSTALLATION STEP 11 Fasten the Door Bracket To prevent damage to garage door, reinforce inside of door with angle iron both vertically and horizontally. Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace should be long Header enough to be secured to two or three vertical Bracket supports. A vertical reinforcement brace should cover the height of the top panel. Figure 1 shows one piece
Краткое содержание страницы № 19
INSTALLATION STEP 12 Inner Trolley Connect Door Arm to Trolley SECTIONAL DOORS ONLY Outer Trolley •Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer Clevis Pin trolley from the inner trolley. Slide the outer trolley 5/16"x1" Ring back (away from the door) about 2" as shown in Fastener Figures 1, 2 and 3. •Figure 1: – Fasten straight door arm section to outer trolley with the 5/16"x1" clevis pin. Secure the Door connection with a ring fastener. Brac
Краткое содержание страницы № 20
ADJUSTMENT STEP 1 WARNING WARNING Adjust the UP and DOWN Travel Without a properly installed safety reversal system, Limits persons (particularly small children) could be CAUTION WARNING SERIOUSLY INJURED or KILLED by a closing garage Limit adjustment settings regulate the points at which door. the door will stop when moving up or down. • Incorrect adjustment of garage door travel limits will To operate the opener, press the Door Control push interfere with proper operation of safety reversal ba
