Краткое содержание страницы № 1
Dome E2c Display
Quick Reference
Windows XP
Windows 2000
0 020-0458-00A_3.indd 1 20-0458-00A_3.indd 1 4 4/12/06 5:36:29 PM /12/06 5:36:29 PM
Краткое содержание страницы № 2
Read all instructions before setting up the Dome E2c display. Improper use of the display can result in electric shock, fi re, or damage to display components. For more product information, go to www.planar.com/support. System Requirements • Intel Pentium 4/Xeon; AMD Athlon 64/K7/XP or compatible • PCI Express x16 lane slot • 50 MB hard disk space • 256 MB RAM W a rning Warnung • CD-ROM drive Avertissement • Power supply, 350 watts Avvertenza or greater Advertencia • Windows XP or Wind
Краткое содержание страницы № 3
Unpacking the Display Check the contents of your Dome E2c display package for all the items shown here. Save the original packaging materials for storage and shipping. Video card DVI cable Dome E2c display Power adapter Power cord Software CDs Also included: Composite Video, S-Video, and VGA cables. 3 020-0458-00A_3.indd 3 020-0458-00A_3.indd 3 4/12/06 5:36:35 PM 4/12/06 5:36:35 PM
Краткое содержание страницы № 4
Display Components The high-bright UXGA 1200x1600 AMLCD panel is sized to a 541 mm (21.3 in.) display screen. The reset button, LED indicator, and input power and video ports are located on the back of the display. No other user-accessible controls are available. You can change the brightness of the Dome E2c display in the Display Properties dialog of the Windows operating system. However, when DICOM auto-calibration is running, you must control display bright- ness via the Dome CXt
Краткое содержание страницы № 5
Legend 1 Reset. Restores default display setting. 2 LED indicator. Shows display status. 3 DIN 8-pin port. Drives power to the display. 4 S-Video, separate video analog input port. Requires a 4-pin mini-DIN connector. 5 C-Video, composite video analog input port. Requires an RCA or phono connector. 6 DVI, DVI-I video input port. Supports DVI-D digital or DVI-A analog video. Requires DVI connector. 7 VGA. VGA video analog Back view 8 9 input port. Requires an HD15 D-Sub or VGA conn
Краткое содержание страницы № 6
Installing the Display Controller Remove any existing graphics card and its driver from your computer system before you install the controller and driver. Also disable any onboard graphics capability on the motherboard. See safety precautions on page 2. To install the controller 1 Turn off your computer and all peripherals. Disconnect all cables from your computer. Leave the power cord plugged into the grounded outlet. 2 Remove the computer cover. 3 Remove any existing graphics card
Краткое содержание страницы № 7
Connecting the Display U se only the cables and power cord supplied with your display. To connect the display 1 Plug one end of the DVI signal cable to the DVI port on the display. Tighten the thumbscrews to secure the connection. 2 Plug the power cord into the power connector on the connector plate. 3 Plug the other end of the DVI cable into the video port on the installed controller. (Use DVI port #1 for Power cord DVI cable the fi rst display if you are installing only one display.)
Краткое содержание страницы № 8
Installing the Display Driver Upon restarting your computer system, you must log on with administrator privileges. On Windows 2000 systems, Service Pack 4 or higher must be installed. To install the display driver 1 Start the system. Click Cancel on the Found New Hardware Wizard dialog box. 2 Insert the Planar Installation CD and run the SETUP.EXE utility. 3 Click Next on the Welcome dialog. 4 Click Yes to the license agreement. The installation starts. 5 Follow the onscreen instructions to com
Краткое содержание страницы № 9
Adjusting the Display Properties Use the Display Properties dialog to make changes to the video settings or to set up dual-display confi guration. To set the display orientation 1 Right-click the desktop and select Properties > Settings. 2 Select the monitor that you want to change. Then click Advanced. 3 Click the Monitor tab. Make sure the check box for Hide modes that this monitor cannot display is empty (unchecked). 4 Click the Rotation tab. • Check Standard Landscape for landscape mode. •
Краткое содержание страницы № 10
Handling the Display • Set up your display on a stable, • Avoid sudden temperature changes level surface away from any direct in the environment, as this may light or heat source, but near a cause condensation, which damages grounded AC outlet. the display. • Choose a well-ventilated location • Never remove the back cover or with an adequate amount of space. disassemble the display. There are Do not block the vents on the back no user-serviceable parts inside. of the display. • In locations
Краткое содержание страницы № 11
Cleaning the LCD Screen Use a dry, clean, lint-free cotton cloth to remove surface dust from the display screen. Do not use chemically treated dust cloths. To remove grease or organic contaminants, follow this procedure: 1 Disconnect the power supply from the display. 2 Dampen a soft, clean cloth with a small amount of isopropyl alcohol. 3 Wipe the display screen gently with the dampened cloth. 4 Use a dry, clean, lint-free cotton cloth to wipe off the residue. Do not spray or use Do n
Краткое содержание страницы № 12
America Sales Europe Sales Planar Systems, Inc. European Representative 1195 NW Compton Drive Planar Systems, Inc. Beaverton, OR 97006-1992 USA Olarinluoma 9, P. O. Box 46 FIN-02201 Espoo, Finland (503) 748-1100 phone (503) 748-1493 fax + 358 9 420 01 phone + 358 9 420 0200 fax Medical Sales vertrieb@planar.com Planar Systems, Inc. medicalsupport@planar.com 400 Fifth Avenue www.planar.com Waltham, MA 02451-8738 USA Asia-Pacifi c Sales (781) 895-1155 phone Planar Systems, Inc. (781) 895-113
