Краткое содержание страницы № 1
INSTRUCTION MANUAL CCA-BC200
Rear View Back up Camera System
CAUTION
• Installation and wiring require technical expertise and experience. To ensure
proper installation and safety, consult the dealer where the product was
purchased.
SANYO’S HELP-LINE
Call the toll-free number below if you have any difficulties operating this product.
1-800-421-5013 (Weekdays 7:30 AM – 5:00 PM, Pacific Time)
Краткое содержание страницы № 2
1
Краткое содержание страницы № 3
CONTENTS SAFETY PRECAUTIONS···································································································· 2 SPECIFICATION················································································································· 4 BEFORE USING THE REAR VIEW BACK UP CAMERA SYSTEM···································· 5 ACCESSORIES AND HARDWARE ···················································································· 6 REAR VIEW BACK UP CAMERA SYSTEM O
Краткое содержание страницы № 4
• When installing this Rear View Back up Camera System to a vehicle equipped with air bags (The name differs depending on the manufacturer, such as SRS dual air bag, SRS side air bag, SRS curtain air bag), do not install this Rear View Back up Camera System or route its wiring where it affects operation of the air bag system. If the air bags do not operate properly in an emergency, an accident or injury can occur. (Consult the dealer where the product was purchased to determine the instal
Краткое содержание страницы № 5
• Route wiring properly according to the instructions. An incorrect connection might cause a fire or accident. • Be careful and prevent the wiring harness from being pinched between the vehicle body, screws, or moving parts such as the seat rails. It could cause an accident, electrocution, or fire due to an open or short circuit. • The Rear View Back up Camera System is for in-car use only and is not to be used outside of the vehicle. If it is used outside of the vehicle it could result
Краткое содержание страницы № 6
BEFORE USING THE REAR VIEW BACK UP CAMERA SYSTEM Regarding methods of use • The Rear View Back up Camera System is a devise designed only to assist the driver. The driver must take full precautions to confirm the safety and conditions around the vehicle. • Water droplets on the camera lens could adversely affect the image. • The positioning appearing on the screen changes according to the vehicle conditions (number of occupants and weight of cargo). Always directly confirm the safety
Краткое содержание страницы № 7
ACCESSORIES AND HARDWARE Make sure all the following parts are included in the Rear View Back up Camera System kit. 1 Control switch cable…….1 pc. (approx. 8.20 ft. long, Power supply cable……1 pc. Rear view camera………1 pc. with double sided tape) (approx. 4.92 ft. long, with fuse) (with approx. 26.2 ft. long cable) Hook-and-loop fastener…1 set ECU box…….........….1 pc. Video output cable…...1 pc. (for ECU box) (Electronic Control Unit box) Hexagon wre
Краткое содержание страницы № 8
REAR VIEW BACK UP CAMERA SYSTEM OUTLINE Camera Virtual camera View-from-top Display mode Standard rear view Including the standard rear view image captured by the camera, a digitally corrected rear view, view-from-top, and standard rear view can be selected. Guide lines are indicated in order to assist the driver and assure safety when backing up. Standard rear view Digitally corrected rear view Left/right guide lines (Green) (Guide lines to indicate width of
Краткое содержание страницы № 9
CAUTIONS FOR CONNECTION CAUTION • Before connecting, disconnect the negative battery terminal. Connect the negative battery terminal after all other connections are completed. • Connection terminals and cables are differentiated by color. Make connections to the same colors. Make sure connectors are securely inserted until a click sound is heard. Incomplete connection may cause a distorted picture or operation errors. • Before disconnecting the connector, turn the igniti
Краткое содержание страницы № 10
CONNECTION Control switch Rear view camera ECU box connection terminal connection terminal (Green) (Black) Video output connection terminal Connect the Power supply (Yellow) cable according connection terminal to the color and (Brown) shape of the terminal Power supply cable (Yellow) (Brown) Video output cable (RCA Type) Connect firmly to a (Black) metal part of vehicle Connect to (for grounding) Camera input (Yellow) terminal or video input Connect t
Краткое содержание страницы № 11
BEFORE INSTALLATION Rear View Back up Camera System Installation Cautions • Bundle cables with tape or string so that they do not obstruct driving. Cables that become entangled in the steering wheel, shift selector lever or brake pedal could cause an accident. • Peel off the paper backing from the tape on the camera bracket and firmly attach the bracket to the surface of the vehicle. If the tape is not completely adhered to the surface, the camera bracket might become loose and fall of
Краткое содержание страницы № 12
Determination of Camera Installation Position (example) • Temporarily adhering the camera with the tape, locate a suitable installation position by adjusting the camera angle so that the rear of the vehicle (bumper and other areas) is visible in the monitor. • Install the camera in a position that does not allow the illumination of a high-mount brake light to reflect into the camera lens. • Make sure the camera does not contact or rub against the vehicle body when the rear door opens o
Краткое содержание страницы № 13
INSTALLATION Installing system on rear spoiler 1. Clean the location where the camera is to be installed. Wipe off oil, wax, moisture, dirt and dust using a cleaner and a clean cloth. 2. Peel off the paper backing from the tape on the camera bracket and firmly attach the bracket to a flat surface on the rear spoiler. Press the bracket with a finger to assure good contact of the bracket to the surface of the vehicle. Touching the Bracket sticky surface of the tape with a fing
Краткое содержание страницы № 14
4. Adjust the camera angle so that the extreme rear end of the vehicle (bumper, rear window, and liftgate.) is displayed at the bottom of the monitor. Need help? Call Extreme rear end of vehicle (bumper etc.) 1-800-421-5013 • After adjusting the angle, tighten the screws Loosen with them seated at the lower end of the oblong holes in the bracket on each side. Tighten CAUTION • Verify the tightness of the screws and tighten them more if necessary. CAUTION • A
Краткое содержание страницы № 15
Control switch 7. Install the control switch in a position where it is easy to operate. Peel off the paper backing on the back of the control switch and attach it to a suitable position. CAUTION • Do not install the control switch in a position that obstructs vehicle operation. How to use self-lock conductor Vehicle reverse signal cable 1. Insert the reverse signal cable of the vehicle into the self-lock conductor. 2. Fold the self-lock conductor and
Краткое содержание страницы № 16
CABLE ROUTING The following is an example when installing the camera on the rear spoiler. Control switch Camera ECU box CAUTION • Route the cable so that it does not block or obstruct vehicle operation. • Route the rear view camera cable as far away from the vehicle antenna as possible to prevent noise interference with AM radio band reception. Also, route the cable as far as possible from a TV antenna, if equipped. • Clean the areas where the cable clamps and
Краткое содержание страницы № 17
3. Route the camera cable to the ECU box positioned inside the vehicle and clamp it using the cable Luggage finish plate clamps. 0.1 in Insert the cable into the slit provided in the 0.1 in waterproof pad and attach the waterproof pad to the weather strip on the vehicle at the point where Position with no ribs on the rear side the cable enters the vehicle. Waterproof pad Weather strip Control switch ECU box 4. Route the control switch cable to the ECU box and secure it
Краткое содержание страницы № 18
GUIDE LINE ADJUSTMENT AFTER REAR VIEW CAMERA INSTALLATION The guide lines on the screen need to be aligned with the image taken from the rear view camera (and other reference items) so that the system is correctly matched to the vehicle. There are seven reference items to align including, (1) View-from-top angle alignment (2) Center-line alignment (3) View-from-top height alignment (4) Left/right guide lines alignment (5) Right guide line alignment (6) 3 ft. guide line alignment
Краткое содержание страницы № 19
Seven rectangles at top left indicate Alignment Mode seven items to align Turn the ignition switch to the ACC ON position while depressing the control switch. • Press and hold the control switch until the screen appears. View-from-top alignment screen appears. (Seven rectangles at top left indicate seven items to align.) If adjustment mode cannot be selected 1. Turn the ignition switch to the ACC ON position while pressing the switch. Press and hold the switch for two second
Краткое содержание страницы № 20
1. View-from-top angle alignment (flashing white rectangle) 1-1. Each time the control switch is pressed, the angle increases. Continuously pressing the control switch returns the alignment to the original angle. Set the parking space lines parallel to the lines on the screen. 1-2. Press and hold the control switch for more than two seconds. The view-from-top angle alignment is now set and the screen changes to the center-line alignment setting. The center guide
