Руководство по эксплуатации Audiovox AX-45

Краткое содержание страницы № 1

Model AX-45
Installation Manual
Keyless Entry System
With Two Auxiliary Outputs
Installation Instructions
This Unit Is Intended For Installation In Vehicles With
12 Volt Negative Ground Electrical Systems Only.
Kit Contents:
(1) Control Module
(2) - Three Button Transmitters
4 Channel Code Learning Receiver
On Board Antenna
(1) - Multi Pin Input/Output Harness
(1) - Three Pin Door Lock Harness
(1) - Two Pin LED Indicator
(1) - Two Pin Valet / Override Switch
(1) - 15 Amp In-li

Краткое содержание страницы № 2

This Keyless Entry System is designed to provide a convenient electronic means to gain access to the vehicle by providing RF remote control over the vehicle's power door lock system. The unit also includes outputs to control the vehicle's dome lights, as well as exterior parking lights. Although not an alarm system, this unit also incudes a starter interrupt circuit output. It also includes two additional auxiliary outputs designed to allow for control over optional devices such as a power tr

Краткое содержание страницы № 3

This wire is designed to output a +12VDC positive light flash output, driven by the UNITS's internal relay, to be connected directly to the vehicle's positive parking light circuit. Once the wire is located, confirm that all the vehicle's parking lights will illuminate when +12VDC is connected to it. NOTE: Some vehicles, (mostly European) have isolated "left" and "right" side parking lights. To connect to the parking light systems in these vehicles, you must use separate SPDT relays to connect

Краткое содержание страницы № 4

WHITE/BLUE Wire: Immediate, 300mA Duration of Transmit, Channel 4 Output This wire supplies a 300mA switched output whenever Channel 4 of the receiver is accessed. Pressing A combination of the transmitter Lock/Unlock buttons simultaneously will access Channel 4 and will remain active for as long as the transmitter button(s) is held. This is a low current output and must be connected to a relay to supply power to the device you intend to control. Connect this wire to terminal #86 of a VF45F

Краткое содержание страницы № 5

terminal 87, to a fused + 12 volt source. In the rare instance that the vehicle door lock/unlock motor legs rest at + 12 volts and switches ground to the door lock/unlock motors, connect the remaining terminal 87, to chassis ground. The Blue/Red wire provides a pulse ground output when the unlock button of the transmitter is pressed a second time after unlocking the driver's door. Connect the Blue/Red wire to the wire that provides a low current ground signal from the factory door unlock switc

Краткое содержание страницы № 6

"Programming System Features" shown later in this installation guide to learn the operation of the valet/program/manual override switch. POWER DOOR LOCK HARNESS 3PIN White Plug w/3 Wires; Green, Blue & Blue/Red The connection of the power door lock/unlock wires has already been explained. Route the three pin connector to the unit and plug the connector into the mating white three pin connector shell of the control module. Do not force the connector, it will only plug in one way. PROGRAMMING FE

Краткое содержание страницы № 7

Second Turn the valet switch on then off 2 chirps = auto locks off 2 Flash pause Press transmitter Lock button to change 1 chirp = auto locks on or Third Turn the valet switch on then off 2 chirps = auto unlock off 3 Flash pause Press transmitter Lock button to change 1 chirp = auto unlock on or Fourth Turn the valet switch on then off 1 chirp = chirps on 4 Flash pause Press transmitter Lock button to change 2 chirps = chirps off or Fifth Turn the valet switch on then off 2 chirps = active locks

Краткое содержание страницы № 8

© 2003 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y., 11788 128-6992 128-6992 8 of 8