Краткое содержание страницы № 1
INSTRUCTION MANUAL
DP-HG22
PLASMA MONITOR (DISPLAY)
WALL HANGER UNIT
HW
AA
NL
GL
E
R
U
N
I
T
Thank you for purchasing the Daewoo Electronic Plasma Display Wall Hanger Unit. This
wall unit is specifically designed for use with the Daewoo Plasma Display. To ensure the
safe operation of the unit, please read these instructions before installing.
Краткое содержание страницы № 2
TABLE OF CONTENTS .............................. 1. Check for enclosed parts 2 ........................ 2. Important Safety Instructions 3 ................................... 3. Assembly Instructions 6 ................ 4. Adjusting angles after installation 12 To install the wall hanger unit, Please * consult an Authorized service center first. 1
Краткое содержание страницы № 3
PLASMA DISPLAY HANGER UNIT 1. PLEASE CHECK THE ITEMS SHOWN BELOW FRAME SET A FRAME SET B (2) (2) CONNECTING FRAME CONCRETE WALL ANCHOR (1) (8) M5 SCREWS (20 MM) WALL SCREWS HW AA NL GL E R U N I (12) (8) T PAPER PATTERN PLAN M5 SCREWS (30MM) Paper pattern plan (1) (2) 2
Краткое содержание страницы № 4
2. IMPORTANT SAFETY INSTRUCTIONS PLEASE FOLLOW THESE INSTRUCTIONS FOR YOUR SAFETY PLEASE KEEP THESE INSTRUCTIONS FOR YOUR SAFETY AND TO PREVENT ANY DAMAGE TO THIS UNIT. WARNING : Disregarding these instructions can result in serious injury. WARNING CAUTION : Disregarding these instructions will result in the mistreatment of the unit and can result in injury or damage to the unit. CAUTION PLEASE CONSULT AN AUTHORIZED SERVICE CENTER TO INSTALL THE WALL HANGER UNIT * To install the wall hanger unit
Краткое содержание страницы № 5
PLASMA DISPLAY HANGER UNIT PLEASE FOLLOW THESE SAFETY PRECAUTIONS WHEN INSTALLING OR HANDLING * Special care is needed when installing onto the When installing, please wear working gloves. wall due to its weight (35Kg) When installing on a concrete wall Please be sure to use the enclosed concrete anchors. (If done with bare hands, it may result in injury) Be sure that no one is around to distract you during the installation process. When installing on a wooden wall take special care as the unit
Краткое содержание страницы № 6
PLEASE FOLLOW THESE SAFETY PRECAUTIONS WHEN INSTALLING OR HANDLING * When installing, please use the size referenced below to choose a place, and attach the paper pattern plan to the wall. 519.5 519.5 Paper pattern plan . Measurement unit : mm It is important to use the paper pattern plan to choose the proper place; otherwise, it can result in damage to the wall and you will not be able to install the unit When installing, please allow at least 15 cm at the top, bottom, left and right on the wal
Краткое содержание страницы № 7
PLASMA DISPLAY HANGER UNIT 3. ASSEMBLING INSTRUCTIONS PREPARATION WHEN THE PLASMA DISPLAY IS ATTACHED TO THE STAND TO DETACH THE STAND FROM THE PLASMA DISPLAY 1 . . To avoid unwanted marks on the unit, place Unscrew the secured 2 screws completely a protective covering over the surface you and Pull the stand away from the plasma will be working on and lay the plasma display to detach. display as shown below. TO PLACE THE PROTECTIVE CAPS 2 HW AA NL . . There will be two holes where the stand Put
Краткое содержание страницы № 8
CORRIGENDA MODEL: DP-HG22 INSTALLING THE WALL FRAME SET A ON THE PLASMA DISPLAY PANEL . Replace the previous instruction (#2) with the following updated one. . Four M5 screws are not used out of total number. . Make sure the installation is secure. . Installation by professional is preffered. . Contact infomation for any question. 1-800-DAEWOO-8 #8 1-201-964-9349 Service@daewoodigital.com HOW TO INSTALL FRAME SET A ON THE UNIT 2 . . To avoid unwanted marks on the
Краткое содержание страницы № 9
Paper pattern plan PLASMA DISPLAY HANGER UNIT INSTALLING WALL FRAME SET B AND CONNECTING FRAME INSTALLING WALL FRAME SET B AND CONNECTING FRAME. 1 Frame set B . Place frame set B on the left and right side of Connecting Frame the unit and use the enclosed screws (M5) to secure them tightly. Note . Please be sure to not force an adjustment when connecting frame set B and connecting frame. . Otherwise, it will create problems when connecting to frame set A. ATTACHING PAPER PATTERN PLAN ON THE W
Краткое содержание страницы № 10
Paper pattern plan Paper pattern plan INSTALL THE WALL FRAME SET ON THE WALL 3 . Install the wall frame set on the wall by matching the concrete anchors with the holes, then use the wall screws (8) to secure tightly. INSTALLING ON THE WALL HELD BY SUPPORTING WOODEN STRUCTURE 4 . If it is not feasible to attach frame set B firmly and completely, due to the distance between the two supporting woods; attach one side of the frame set B firmly to the supporting wood, and use appropriate remaining h
Краткое содержание страницы № 11
PLASMA DISPLAY HANGER UNIT INSTALLING PLASMA DISPLAY ON THE WALL CONNECTING UPPER PART OF FRAME SET A AND FRAME SET B 1 . Insert the upper part of frame set A (X) to frame (X) set B (Y) as indicated below. Frame set B (Y) Frame set A At least two people are needed to put these frames together. * HW AA CONNECTING LOWER PART OF FRAME SET A AND FRAME SET B 2 NL GL E . Adhere Frame set B to Plasma Display unit, then, take the lower part of Frame R set B as pictured below and push the (Z) part up g
Краткое содержание страницы № 12
TO PROVIDE THE SECUREST FIT 3 . After installing plasma display and wall frame sets, for a more secure fit, secure M5 screws (M5x30) on the (Z) part so that (Z) will not move up and down as shown in the picture below. 11
Краткое содержание страницы № 13
PLASMA DISPLAY HANGER UNIT 4. ADJUSTING ANGLES AFTER INSTALLATION (10˚, 15˚, 20˚) HOW TO ADJUST VIEWING ANGLES 1 . Take out the screws from the upper part of the frame. . Insert the upper part of the frame set B angle adjustment lever to its gap. . As pictured below, pull and adjust the lever (X) to fit your desired viewing angle. Lever (X) Note . This adjustment needs to be done when the plasma display is tightly secured. Otherwise, the unit can fall and break. . Please retain the two screws
