Руководство по эксплуатации Metra Electronics 99-8710

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS FOR PART 99-8710
APPLICATIONS
Mercedes C-Class 2001-2004
Mercedes CLK 2004
99-8710
KIT FEATURES
• DIN Radio Provision with Pocket
KIT COMPONENTS
A) Radio Housing
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Torx Screwdriver
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION

Краткое содержание страницы № 2

99-8710 TABLE OF CONTENTS Dash Disassembly - Mercedes C-Class 2001-2004 .... ........ ....... ........ ........ ...1 - Mercedes CLK 2004 .... ........ ....... ........ ........ ....... ....2 Kit Assembly - DIN Mount Radio Provision ...... ....... ........ ........ .... ... ... 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installa

Краткое содержание страницы № 3

99-8710 DASH DISASSEMBLY MERCEDES C-CLASS 2001-2004 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip shifter trim (with gear indica- tors). Unclip and remove center console 3 trim panel. (Figure A) 4 Remove the ashtray insert by releas- ing (2) plastic clips on the bottom lip of the ashtray assembly. (Figure B) B 5 Using a small flat screwdriver push the lower clip (“A”) inward and rotate the vent upward to expose (1) Torx head screw. Loosen the To

Краткое содержание страницы № 4

99-8710 DASH DISASSEMBLY MERCEDES CLK 2004 *Note: Refer also to the instructions included with the aftermarket radio. 1 Disconnect the negative battery termi- A nal to prevent an accidental short cir- cuit. 2 Loosen shifter boot and pull up over shifter handle. (Figure A) 3 Turn the retainer on the shifter 1/2 turn to remove shifter handle and boot. (Figure B) 4 Unclip and remove the shifter trim panel. (Figure C) 5 Remove the ashtray insert by releasing (2) plastic clips on the bottom lip of

Краткое содержание страницы № 5

99-8710 KIT ASSEMBLY DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure A) 2 Slide the DDIN radio unit into the trim plate bracket assembly and secure the unit to the kit using the screws sup- plied with the head unit. (Figure B) Continue to final assembly. B 3

Краткое содержание страницы № 6

99-8710 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Краткое содержание страницы № 7

99-8710 NOTES 5

Краткое содержание страницы № 8

99-8710 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 08/07/08 © COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION INST99-8710