Руководство по эксплуатации Metra Electronics 99-8223

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS FOR PART 99-8223
APPLICATIONS
Toyota Corolla
2009-10
99-8223/
99-8223S
KIT FEATURES
• DIN Radio With Pocket Provision
• ISO Mount Radio with Pocket Provision
• Painted To Match Factory Dash
99-8223= BLACK
99-8223S= SILVER
KIT COMPONENTS
• A) Radio Housing • B) Radio Housing Trim Plate • C) Radio Housing Brackets
•D) ISO Brackets • E) ISO Trim Plate
A
B
C
Harness & Antenna Connections (sold separately)
• 70-1761 Toyota Harness 87-up
E
D
• TYTO-01 Toyota Amp Inter

Краткое содержание страницы № 2

99-8223 TABLE OF CONTENTS Dash Disassembly - Toyota Corolla 2009-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - DIN Radio with Pocket Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - ISO Mount Radio with Pocket Provision . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included with the aftermarket radi

Краткое содержание страницы № 3

99-8223 DASH DISASSEMBLY Toyota Corolla 2009-10 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove the (4) side trim panels from the right and left side of the radio and a/c controls. (Figure A) 3 Unclip and remove the a/c vent panel above the factory radio.(Figure B) 4 Remove (4) 10 MM bolts securing the radio. (Figure C) B 5 Remove (4) plastic clips from the back of the factory radio. (Retain the clips for re-use during kit assembly.) Con

Краткое содержание страницы № 4

99-8223 KIT ASSEMBLY DIN RADIO WITH POCKET PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the clips removed from the fac- tory radio to the back of the radio housing trim plate. (Figure A) 2 Slide the Radio Housing Brackets onto the sides of the Radio Housing until the side clips engage. NOTE: Tabs are marked Left and Right. (Figure B) 3 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure C) 4 Sl

Краткое содержание страницы № 5

99-8223 KIT ASSEMBLY ISO MOUNT RADIO WITH POCKET PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the clips removed from the fac- tory radio to the back of the radio housing trim plate. (Figure A) 2 Slide the Radio Housing Brackets onto the sides of the Radio Housing until the side clips engage. NOTE: Tabs are marked Left and Right. (Figure B) 3 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure C) 4 Slide the radi

Краткое содержание страницы № 6

99-8223 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble in reverse order of disassembly using the 99-8223 Rad

Краткое содержание страницы № 7

99-8223 NOTES 5

Краткое содержание страницы № 8

99-8223 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 04/29/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-8223