Руководство по эксплуатации Metra Electronics 99-8205

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS FOR PART 99-8205
APPLICATIONS
Toyota Matrix 2003-2008
Pontiac Vibe 2003-2008
99-8205
KIT FEATURES
• DIN head unit provision
• ISO DIN head unit provision
• DDIN head unit provision
- Excluding 2005-2008 Matrix
• Stacked ISO DIN head unit provision
- Excluding 2005-2008 Matrix
KIT COMPONENTS
A) DDIN Faceplate (excluding 2005-2008 matrix) • B) ISO DIN Faceplate (excluding 2005-2008 matrix)
• C) ISO DIN Faceplate 2005-2008 Matrix D) Pocket • E) Mounting Bracket

Краткое содержание страницы № 2

99-8205 TABLE OF CONTENTS Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1,2 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 4, 5, 6, 7,8 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com

Краткое содержание страницы № 3

TUNE AM FM1 FM2 DISK SCAN SEEK TRACK DASH DISASSEMBLY 99-8205 TOYOTA MATRIX 2003-2008 PONTIAC VIBE 2003-2008 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the bottom edge of the radio trim panel then lift up and out to remove. (Figure A) 3 Remove (4) 10 MM bolts securing the factory radio. (Figure B) B 1

Краткое содержание страницы № 4

KIT ASSEMBLY 99-8205 DIN HEAD UNIT PROVISION A 1 Choose the correct faceplate for your application. The 2005-2008 Matrix #8x3/8” Screw faceplate is smaller than the other supplied faceplate. 2 Attach the pocket to the back of the ISO/DIN Faceplate (by holding the #8x3/8” Screw faceplate upside down and inserting the right edge of the pocket into place then pushing the rest of the pocket onto the lip) and mount with B (2) #8X3/8” Phillips screws. (Figure A) NOTE: For the 2005-2008 Matrix, break

Краткое содержание страницы № 5

KIT ASSEMBLY 99-8205 DIN HEAD UNIT PROVISION D Mount the rear support to the back 4 #6x1/4” Screws Two #8x3/8” Screws of the pocket with (2) #8X3/8” Phillips screws. (Figure D) 5 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure E) 6 Slide the aftermarket head unit into the cage and secure. (Figure F) E #6x1/4” Screws F 3

Краткое содержание страницы № 6

99-8205 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION A 1 Choose the correct faceplate for your #8x3/8” Screw application. The 2005-2008 Matrix faceplate is smaller than the other supplied faceplate. #8x3/8” Screw 2 Attach the the pocket to the back of the ISO/DIN Faceplate (by holding the face- plate upside down and inserting the right edge of the pocket into place then push- B ing the rest of the pocket onto the lip) and mount with (2) #8X3/8” Phillips screws. (Figure A) NOTE: For the 2005-2008 M

Краткое содержание страницы № 7

99-8205 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION D 4 Mount the rear support to the back #6x1/4” Screws Two #8x3/8” Screws of the pocket with (2) #8x3/8” Phillips screws. (Figure D) 5 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure E) 6 Slide the the head unit into the radio opening until the side clips engage. E (Figure F) #6x1/4” Screws 7 Snap the Trim plate into the Radio Housing. (Figure F) F 5

Краткое содержание страницы № 8

99-8205 KIT ASSEMBLY DOUBLE DIN HEAD UNIT PROVISION A NOTE: 2005-2008 Matrix not applicable. 1 Cut and remove the bottom portion (Displayed) of the mounting brack- ets. (Figure A) 2 Cut and remove the center bar from the DDIN faceplate. (Figure B) B 3 Attach the ISO spacers to the mounting brackets by inserting the (4) bosses on each spacer into the (4) holes in each bracket. (Figure C) 4 Attach the mounting brackets to the DDIN head unit with the screws sup- plied with the unit. (Figure D) C

Краткое содержание страницы № 9

99-8205 KIT ASSEMBLY STACKED ISO DIN HEAD UNIT PROVISION A NOTE: 2005-2008 Matrix not applicable. 1 Cut and remove the bottom portion (Displayed) of the mounting brack- ets. (Figure A) 2 Attach the ISO spacers to the mount- ing brackets by inserting the (4) B bosses on each spacer into the (4) holes in each bracket. (Figure B) 3 Attach the mounting brackets to the DDIN head unit with the screws sup- plied with the unit. (Figure C) 4 Attach the DDIN faceplate over the head unit by snapping the

Краткое содержание страницы № 10

KIT ASSEMBLY 99-8205 FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. 2 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring co

Краткое содержание страницы № 11

99-8205 NOTES 9

Краткое содержание страницы № 12

INST998205 1-800-221-0932 www.metraonline.com © COPYRIGHT 2004-08 METRA ELECTRONICS CORPORATION REV. 09/26/08 INST99-8205