Руководство по эксплуатации Metra Electronics 99-2008

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS FOR PART 99-2008
APPLICATIONS
Cadillac DTS 2006-2010
Cadillac SRX 2007-2009
99-2008
KIT FEATURES
• DIN Radio Provisiion with Pocket
• ISO Mount Radio Provisiion with Pocket
• Double DIN Radio Provisiion
• Stacked ISO Mount Units Provisiion
KIT COMPONENTS
A) Radio Housing • B) ISO Trim Plate • C) ISO Brackets • D) Double DIN Trim Plate
• E) Double DIN Brackets • F) Pocket
D
B C
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
• GMOS-LAN-01 - GM LAN Interface

Краткое содержание страницы № 2

99-2008 TABLE OF CONTENTS Dash Disassembly Chevrolet - Cadillac DTS 2006-2010. ... ... .... ... .... ... .... ... ...1 - Cadillac SRX 2007-2009 . ... .... ... .... ... .... ... .... . 2 Kit Assembly DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 4 Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Final Assembly . . .

Краткое содержание страницы № 3

99-2008 DASH DISASSEMBLY Cadillac DTS 2006-2010 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove the trim panel around the radio, climate controls and ac vents and above glove box. (Figure A) 3 Remove (4) 9/32” screws securing the a/c vent panel. Unplug and B remove the panel. (Figure B) 4 Remove (4) 9/32” screws securing the climate controls. Unplug and remove the climate controls. (Figure C) 5 Remove (4) 9/32” screws securing the radio.

Краткое содержание страницы № 4

99-2008 DASH DISASSEMBLY Cadillac SRX 2007-2009 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove trim piece between shifter and cup holders. (Figure A 3 Unclip and remove the trim panel around the radio, climate controls, B ac vents and front half of center console. (Figure B) 4 Remove (3) 9/32” screws securing the a/c vent panel and remove the panel. (Figure C) 5 Remove (4) 9/32” screws securing the climate controls. Unplug and remove th

Краткое содержание страницы № 5

99-2008 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Snap the pocket into the housing. (Figure C) B Continue to final assembly. C 3

Краткое содержание страницы № 6

99-2008 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the trim plate onto the front of the radio housing. (Figure B) 4 Snap the pocket into the housing. (Figure C) B Continue to final assembly. C 4

Краткое содержание страницы № 7

99-2008 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the Double DIN radio or stacked ISO mount units into the bracket/radio housing assembly then secure to the assembly using the screws supplied with the radio or ISO mount units. B (Figure C) 4 Snap the Double DIN Trim

Краткое содержание страницы № 8

99-2008 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disasse