Руководство по эксплуатации Metra Electronics 95-8224

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS FOR PART 95-8224
APPLICATIONS
Toyota Matrix 2009-10
Pontiac Vibe 2009-10
(Excluding Factory Navigation Models)
95-8224
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
• A) Double Din Trim Plate • B) Double DIN Brackets
B
A
Harness & Antenna Connections (sold separately)
• 70-1761 - Toyota Harness 87-up
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Socket Set
1-800-221-0932 www.metraonline.com

Краткое содержание страницы № 2

95-8224 TABLE OF CONTENTS Dash Disassembly - Toyota Matrix/Pontiac Vibe 2009-10 . . . . . . . . . . . . . . . . . . . 1 Kit Preparation ........................... . . . . . . . . . . . . .2 Kit Assembly - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 *Note

Краткое содержание страницы № 3

5 4 3 95-8224 DASH DISASSEMBLY Toyota Matrix/Pontiac Vibe 2009-10 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. PASSENGER SECURITY 2 Unclip and remove the radio trim panel including the a/c vent. (Figure A) 3 Remove (4) 10 MM bolts securing the radio. Unplug and remove the radio. (Figure B) Continue to kit preparation. 2 A/C B 1 1 0

Краткое содержание страницы № 4

95-8224 KIT PREPARATION DOUBLE DIN RADIO PROVISION STACKED ISO MOUNT UNITS *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN Trim plate into the rear of the factory radio trim panel. (Figure A) Continue to kit assembly. 2

Краткое содержание страницы № 5

95-8224 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the Double DIN brackets to the Double DIN or the stacked ISO mount unit(s) using the screws supplied with the unit(s). (Figure A) Continue to final assembly. 3

Краткое содержание страницы № 6

95-8224 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disasse

Краткое содержание страницы № 7

95-8224 NOTES 5

Краткое содержание страницы № 8

95-8224 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 04/27/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST95-8224