Руководство по эксплуатации Metra Electronics 99-6506

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS FOR PART 99-6506
APPLICATIONS
Chrysler Pacifica
2004-2008
99-6506
KIT FEATURES
• DIN Head unit provision with pocket
• ISO DIN Head unit provision with pocket
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) Trim Plate
B
C
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wire harnesses:
• CHTO-02 Chrysler/Dodge amplified interface 2002-up
A
• 70-6506 Chrysler/Dodge amplified bypass harness 2002-up
Antenna adapter:
• 40-CR10 - Chrysler/Dodge antenna

Краткое содержание страницы № 2

99-6506 TABLE OF CONTENTS Dash Disassembly Chrysler Pacifica 2004-2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly Din Head Unit Provision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ISO Din Head Unit Provision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the

Краткое содержание страницы № 3

DASH DISASSEMBLY 99-6506 CHRYSLER PACIFICA 2004-2008 1 Disconnect the negative battery A terminal to prevent an accidental short circuit. 2 Loosen (1) T-15 Torx screw from the P R front side of shift knob and pull up to N D remove. (Figure A) NOTE: For models equipped with no AUTOSTICK release lever on shift knob just turn counter-clockwise to remove. 3 Unsnap floor console trim around the shifter. Unplug harness to console trim and remove trim. (Figure B) Unsnap and remove ignition key 4 B tri

Краткое содержание страницы № 4

KIT ASSEMBLY 99-6506 DIN HEAD UNIT PROVISION A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket head unit into the cage and secure. Snap the Trimplate into the Radio Housing. (Figure B) Note: When DIN mounting a radio a B piece of plastic in the dash cavity may have to be removed for radio depth clearance. (Figure C) C POWER POWER OUTLET OUTLET 2

Краткое содержание страницы № 5

KIT ASSEMBLY 99-6506 ISO DIN HEAD UNIT PROVISION A 1 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) 2 Slide the head unit into the radio opening until the side clips engage. Snap the Trim Plate into the Radio Housing. (Figure B) B 3

Краткое содержание страницы № 6

FINAL ASSEMBLY 99-6506 FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. 2 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring

Краткое содержание страницы № 7

95-6506 NOTES 5

Краткое содержание страницы № 8

99-6506 INSTRUCTIONS 1-800-221-0932 www.metraonline.com © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION REV. 04/20/09 INST99-6506