Руководство по эксплуатации Metra Electronics 99-3306

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS FOR PART 99-3306
APPLICATIONS
Chevrolet Aveo sedan 2007-2010
Pontiac G3 2007-2009
99-3306
KIT FEATURES
• DIN Mount Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Mount Radio Provision
• Stacked ISO Units Provision
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket
C
D
B
A
WIRING AND ANTENNA CONNECTIONS: (Sold Separately)
Wiring Harness:
• 70-21

Краткое содержание страницы № 2

99-3306 TABLE OF CONTENTS Dash Disassembly - Chevrolet Aveo 2007-2010.. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - Pontiac G3 2007-2009 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 2 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 3 - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Краткое содержание страницы № 3

A/C A/C 99-3306 DASH DISASSEMBLY CHEVROLET AVEO 2007-2010 PONTIAC G3 2007-2009 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove trim panel around SOUND SCAN AST radio. (Figure A) 1 3 6 2 4 5 3 Remove (4) 9/32” screws securing the radio. Unplug and remove radio. (Figure B) Continue to kit assembly. B SOUND AST SCAN 1 3 6 2 4 5 2 1 3 4 1

Краткое содержание страницы № 4

99-3306 KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking outward. (Figure A) 2 Slide the aftermarket radio into the DIN cage until it snaps into place. (Figure B) 3 Snap the pocket into the radio housing. (Figure C) Continue to final assembly. B C 2

Краткое содержание страницы № 5

99-3306 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio opening until it snaps into place. (Figure B) 3 Snap the ISO Trim Plate onto the front of the Radio Housing. (Figure B) 4 Snap the pocket into the radio hous- ing. (Figure C) B Continue to final assembly. C 3

Краткое содержание страницы № 6

99-3306 KIT ASSEMBLY DOUBLE DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the Double DIN radio into the bracket/radio housing assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure C) B 4 Snap the Double DIN trim-plate onto the front of the hou

Краткое содержание страницы № 7

99-3306 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the stacked ISO units into the bracket/radio housing assembly and secure the units to the assembly using the screws supplied with the units. (Figure C) B 4 Snap the Double DIN trim-plate onto the front of the housing

Краткое содержание страницы № 8

99-3306 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas