Руководство по эксплуатации Speco Technologies -16/IP

Краткое содержание страницы № 8

4. Front Panel Introduction The DVR-16/IP front panel controls enable you to perform preset and programmable functions. The figures below show the available buttons on the front panels. **DVR-16/IP starts detecting the camera and recording automatically after power is on. 4.1 The Buttons on the Front Panel The following are the introductions of DVR-16/IP front panel buttons. The front panel is illustrated and each button is described by name and function.

Краткое содержание страницы № 9

MENU Press this button to enter OSD setup menu (the LED will be lit). ENTER / ZOOM 1. In OSD menu mode, this button is used to make the selection or save settings. 2. In full-screened mode, this button functions as a “2x2 Zoom In” button (the LED will be lit). DIRECTION 1. These buttons function as directional control in OSD menu. 2. In Zoom mode, press these buttons to view the wanted viewing area. 3. In multi-window mode, the DVR-16/IP allows you to select one window to playback t

Краткое содержание страницы № 10

SET In multi-windows display mode, press this button to enter SET mode. The menu will appear with the cursor over the first window. Use DIRECTION buttons to move the cursor, then press the CHANNEL button to assign the camera directly. The cursor will move to next window automatically. Press ESC button to exit SET mode. MODE Press this button to select display formats (4, 5, 7, 9,10,13 and 16 windows). The camera LEDs of selected cameras should be lit. FAST REWIND In playback mode

Краткое содержание страницы № 11

5. DVR-16/IP Menu Tree Date / Time 2-1 1 Year 2002 Event List 1 2 Month 12 3 Day 4 1 02/10/21 15:58:53 M12 4 Hour 16 2 02/10/21 18:24:30 A 3 5 Minute 5 3 02/10/22 10:19:16 L16 6 Second 20 7 Week MON 8 Exit / Update 9 Exit /

Краткое содержание страницы № 12

Day / Night Switch 6-1 1 Day / Night SW Enable No 2 Switch Day 3 Delay For Active 60 4 Exit Event Response 6-2 1 Internal Buzzer ON 2 Event Relay Output ON 3 Event List ON 4 Event Full Screen OFF 5 Call Event Display ON 10 6 Response Duration

Краткое содержание страницы № 13

Software Information 7-3 1 CPU Filename D6SE0100 2 FPGA Filename FPGA0505 3 Date 2003/01/23 4 Video System NTSC 5 DSP BD HW SK1V3302 6 DSP BD SW SK1V3300 7Exit HDD Information 7-4 1 HDD Size 40GB 2 Free Size 17GB Others 7 3 Total Rec Time 7Hr 4 Free Rec Time ----Hr 1 RS-

Краткое содержание страницы № 14

6. OSD Menu Setup The OSD menu is composed in hierarchy architecture, it allows you to MAIN MENU configure the DVR-16/IP according to the applictation enveironment. 1 Event List 2 OSD / Timer Many options can be selected via the operation of the OSD menu. 3 Monitor 4 Camera To enter this OSD menu, press the MENU button of the front panel, 5 Record 6 Event then the OSD menu will appear with a highlight cursor over the first 7 Others 8 Save / Load Default 9 Engineer item. The curs

Краткое содержание страницы № 15

6.2.4 Date/ Time Position This item allows you to move current Date/ Time Display to any position. Use the DIRECTION buttons to move Date/ Time display. 6.2.5 PB Date/ Time Position This item allows you to move the recorded Date/ Time Display to any position. 6.2.6 RS-485 Time Calibration RS-485 is used for multi-point communications: many devices can be connected to the same bus. Move to this item and press the ETNER button, all DVR-16/IP timers will be synchronized. 6.2.7 Call M

Краткое содержание страницы № 16

6.3.2 Live Refresch Rate This item allows you to setup the camera refresh rate on the Main monitor; use right/ left buttons to select “Fix” or “Auto”. “Fix” means each camera has the same refresh rate. “Auto” means the camera with more motion will get higher refresh rate automatically. 6.3.3 Screen Center Point This item allows you to move the center point of the main monitor. Use the DIRECTION buttons to pan/ tilt the monitor center point. Press ESC button to exit when finished. 6.3.

Краткое содержание страницы № 17

6.4.1.1 Install This item allows you to install each channel on 1 Configuration Table1. Every channel is “installed” by default; you may uninstall any one of them manually. Once a channel is un-installed, all related functions are disabled ( √ = camera installed; • = camera not installed). 6.4.1.2 Covert This item allows you to make each camera’s input invisible (covert) on both main and call monitor, while DVR-16/IP keeps recording the camera’s video. The default setting is every camer

Краткое содержание страницы № 18

PELCO Speed Dome PELCO Speed Dome 1 Protocol Setup D_Type DVR-16/IP is capable of connecting to PELCO Speed Dome; 2 ID Setup 1 3 Zoom the related settings can be adjusted here in this sub-menu. 4 Focus 5 Bfightness You can pan/ tilt PELCO Speed Dome by pressing SET and 6 Set Preset Point 7 Goto Preset Point the direction buttons simultaneously after you are entering 8 Enter Speed Dome Menu 9 Exit this sub-menu. Protocol Setup There are two

Краткое содержание страницы № 19

Goto Preset Point Press right/ left direction button to select the number of the wanted preset point; then press Enter to go to the selected preset point. Set Group Dwell Press the right/ left direction button to choose a proper dwell time. Go Preset Group Press Enter to start sequencing. Stop Preset Group Press Enter to stop sequencing. 6.4.1.4 Termination This item allows you to enable/ disable the terminal resister of each camera. If the camera loop-back connector is not used, t

Краткое содержание страницы № 20

Situation 1: No alarm event happens. 4 Channel 1 PPS = 30* = 6.31 4 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 1 Channel 2 PPS = 30* = 1.58 4 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 1 Channel 3 PPS = 30* = 1.58 4 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 Situation 2: An alarm event happens on channel 2. 4 Channel 1 PPS = 30* = 4.61 4 + 8 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 8 Channel 2 PPS = 30* = 9.23 4 + 8 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 +1 1 Channel 3 PPS =