Руководство по эксплуатации Metra Electronics 95-8208

Краткое содержание страницы № 1

INSTALLATION INSTRUCTIONS FOR PART 95-8208
APPLICATIONS
Toyota Sienna
2004-2010
95-8208
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
• A) Radio Housing • B) Double Din Trim Plate • C) Double DIN Brackets
A
C
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• 70-1761 -Toyota harness 1987-up
• TYTO-01 - Toyota amp harness 2003-up
Antenna Adapter:
• Not required
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool

Краткое содержание страницы № 2

95-8208 TABLE OF CONTENTS Dash Disassembly - Toyota Sienna 2004-2010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included with the aftermarket r

Краткое содержание страницы № 3

95-8208 DASH DISASSEMBLY Toyota Sienna 2004-2010 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove panels from left and right side of radio. (Figure A) 3 Unclip and remove panel or speaker cover above radio. (Figure B) 4 Remove (4) 10 MM bolts securing the radio. Unplug and remove the radio. B (Figure C) Continue to final assembly. C 1

Краткое содержание страницы № 4

95-8208 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure A) 2 Slide the Double DIN radio into the bracket/housing assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure B) 3 Snap the Double DIN Trim plate into the Radio Housing. (Figure C) B Continue to final assembly. C 2

Краткое содержание страницы № 5

95-8208 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure A) 2 Slide the stacked ISO units into the bracket/housing assembly and secure the units to the assembly using the screws supplied with the units. (Figure B) 3 Snap the Double DIN Trim plate into the Radio Housing. (Figure C) B Continue to final assembly. C 3

Краткое содержание страницы № 6

95-8208 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disasse

Краткое содержание страницы № 7

95-8208 NOTES 5

Краткое содержание страницы № 8

95-8208 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 04/27/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST95-8208