Краткое содержание страницы № 1
Technical Manual
Automatic
Glasswasher
Model
MD18-1
MD18-2
Machine Serial No.
July, 2003
Manual P/N 0509243 REV. F
2674 N. Service Road
P.O. Box 4183
Jordan Station, Ontario, Canada L0R 1S0
Winston-Salem, North Carolina 27115-4183
Moyer Diebel, Ltd.
Moyer Diebel, U.S.
905/562-4195
336/661-1992
Fax: 905/562-4618
Fax: 336/661-1979
Краткое содержание страницы № 2
Complete the information below so it will be available for quick reference. __________________________ ________________________ Model Number Serial Number ______________________________________________________________ Voltage and Phase _______________________________ _____________ Moyer Diebel Parts Distributor Phone _____________________________________________________________________________ ________________________________ _____________ Moyer Diebel Service Agency Phone ______________________
Краткое содержание страницы № 3
REVISIONS Revision History Revision Revised Serial Number Comments Date Pages Effectivity 10/30/95 — 301 Issue of Manual and Replacement Parts 1/xx/97 All 301 Expanded Parts List 3/12/01 18, 19 G2735 Redesign of scrap screen and sump cover 3/12/01 24, 25 — Replacement Impeller, Seal/Gasket kit, and Inlet Screen 3/11/01 26, 27 — Added all drain valve components 2/5/03 29 — Replaced 108391 with 113622 thermometer 7/23/03 17 –– Replaced 110229 with 0310138
Краткое содержание страницы № 4
THIS PAGE INTENTIONALLY LEFT BLANK
Краткое содержание страницы № 5
CONTENTS CONTENTS Page WARRANTY.............................................................................................................................................. 1 INTRODUCTION....................................................................................................................................... 2 GENERAL .................................................................................................................................................. 3 INSTALLATION ....
Краткое содержание страницы № 6
CONTENTS Figure 9—Control Panel and Timer Assembly ......................................................................................... 30 Figure 10—Back Panel................................................................................................................................ 32 Figure 11—Rack ......................................................................................................................................... 34 Figure 12—Wiring Schematic..................
Краткое содержание страницы № 7
WARRANTY LIMITED W LIMITED WARRANTY ARRANTY Champion Industries/Moyer Diebel Limited, P.O. Box 4183, Winston-Salem, North Carolina 27115, and P. O. Box 301, 2674 North Service Road, Jordan Station, Ontario, Canada L0R 1S0 warrants machines, and parts, as set out below. Warranty of Machines: Champion Industries/Moyer Diebel Limited warrants all new machines of its manufacture bearing the name “Champion” or "Moyer Diebel" and installed within the United States and Canada to be free from defects
Краткое содержание страницы № 8
INTRODUCTION INTRODUCTION Welcome to Moyer Diebel. Thank you for choosing Moyer Diebel and for allowing us to take care of your glasswashing/ warewashing needs. This manual covers two models (MD 18-1, MD 18-2). Model numbers are shown on the front cover. Your machine has been completely assembled, inspected, and thoroughly tested at our factory to eliminate problems at installation before it was shipped to your installation site. This manual provides: • Warranty information • Installation and op
Краткое содержание страницы № 9
GENERAL GENERAL This manual covers the Moyer Diebel automatic glasswashing machine. Standard equipment includes: -Automatic tank fill -Upper and lower wash/rinse arms -Common utility connections -Two racks -120 Volt circuit -Stainless steel heavy-gauge construction -Convenient, easy to use controls -Pumped Drain -Three chemical pumps This series of glasswashers is available in the following models: Model Numbers MD18-1, MD18-2 • The MD18-1 model is a single door chemical sanitizing rack glasswa
Краткое содержание страницы № 10
GENERAL Electrical Power Requirements Booster Machine Power Requirement Model Voltage Rise Full Load Amp (125% Service Factor) MD18-1 115/60/1 N/A 12 15 MD18-2 115/60/1 N/A 12 15 NOTE: All machines come with a 5 Foot cord and plug. Standard 15 amp receptacle required. 4 J5
Краткое содержание страницы № 11
INSTALLATION INSTALLATION Unpacking WARNING: Care should be taken when lifting the machine to prevent damage. ! 1. Immediately after unpacking your machine, inspect for any shipping damage. If damage is found, save the packing material and contact the carrier immediately. 2. Remove the glasswasher from the skid. Adjust the feet if required, then move the machine to its permanent location. 3. Level the machine (if required) by placing a level on the top of the machine and adjusting the leveling
Краткое содержание страницы № 12
INSTALLATION Plumbing Connections CAUTION: Plumbing connections must comply with local sanitary and plumbing codes. ! Water Connections o o 1. Connect the hot water supply (140 F/60 C Min) to the fill solenoid valve (located behind the front panel). The fill solenoid valve is equipped with a flow control that will accept water pressures from 20 psi to 70 psi. 2. Install a manual shut-off valve in the water supply line to accommodate servicing the machine. The shut-off valve should be the same si
Краткое содержание страницы № 13
Indicates where proper water level should appear in the inlet chute area. Front Side of Tank INSTALLATION Completing Installation 1. Remove any foreign material from inside the machine. 2. Check to assure scrap basket and sump cover are in place. 3. After plumbing and electrical connections are completed, check the machine for water leaks by depressing the ON/FILL switch on the front panel, then close and latch the door(s). This allows the tank to fill and to complete the rinse cycle. Check for
Краткое содержание страницы № 14
OPERATION OPERATION Operation Summary The following is a summary of your Glasswashing Machine operating cycle: 1. The cycle begins when you close the door and push the cycle switch. 2. The green cycle lamp lights and the pump starts. 3. The pump runs during the wash cycle. 4. The pump stops, and the drain valve is opened. 5. After a 2-3 second pause, the pump drain cycle begins. 6. After a 2-3 second pause, the fill valve opens, and the pump starts for the rinse cycle. 7. When the rinse cycle i
Краткое содержание страницы № 15
OPERATION NOTE: The machine may be stopped at any time by opening the door. When restarted, the cycle does not start over. It will continue from the point at which it was interrupted. 7. The pump will automatically stop and the green cycle light will turn off indicating the cycle is completed. 8. Open the door and remove the rack. 9. Repeat steps 4-9 for additional cycles. 10. CLEAN the scrap basket after every use period. During heavy usage, the scrap basket should be cleaned more frequently
Краткое содержание страницы № 16
MAINTENANCE MAINTENANCE The efficiency and life of your machine is increased by regularly scheduled preventive maintenance. A well maintained machine gives better results and service. An investment of a few minutes of daily maintenance will be worthwhile. The best maintenance you can provide is to keep your machine clean. Components that are not regularly cleaned and flushed will clog and become inoperative. Intervals shown in the following schedules represent an average length of time between n
Краткое содержание страницы № 17
MAINTENANCE Deliming Your glasswasher should be delimed regularly as required. This will depend on the mineral content of your water. Inspect your machine interior for lime deposits. If deliming is required, a deliming agent should be used for best results. DANGER: ! Deliming solution or other acids must not come in contact with household bleach (sodium hypochlorite) or any chemicals containing chlorine, iodine, bromine, or fluorine. Mixing will cause hazardous gases to form. Skin contact with
Краткое содержание страницы № 18
MAINTENANCE Maintenance Schedule • As Required 1. Check the temperature gauge reading. 2. Check the chemical supplies and refill as necessary. • Weekly 1. Inspect all water lines for leaks and tighten them at joints if required. 2. Clean all detergent residue from the exterior of the machine. 3. Check the drain for leaks. 4. Clean accumulated scale from the heating element. 5. Remove and closely inspect each spray arm for blockage. 6. Check for damage to the scrap screen. Ineffective screening
Краткое содержание страницы № 19
TROUBLESHOOTING TROUBLESHOOTING Before determining any specific cause of a breakdown or abnormal operation of your glasswasher, check that: 1. All switches are ON. 2. Wash arms are clean. 3. Scrap screen is properly positioned and clean. 4. Thermostat(s) are at their correct setting. 5. Sanitizer, detergent, and rinse additive dispensers are adequately filled. 6. All plumbing valves are open. If a problem still exists, use the following table for troubleshooting. CONDITION CAUSE SOLUTION Machine
Краткое содержание страницы № 20
TROUBLESHOOTING TROUBLESHOOTING CONDITION CAUSE SOLUTION No water in wash well Opening door prior.............................. Close door. Wait for green cycle light to cycle completion to go out before opening door. No water in wash tank Door not closed ................................... Close door. after activating the Wait for wash tank to fill. ON/FILL switch 14
