Краткое содержание страницы № 1
Installation
Instructions
If you have questions, call 800.626.2000 or visit our website at: www.monogram.com
Built-In Dishwashers
ZBD6400, ZBD6500, ZBD6600
ZBD6700, ZBD6900, ZBD7000,
ZBD7100
Chef’s Washers
ZBD6605, ZBD6905, ZBD7005,
ZBD7105
Design Guide with
Installation Instructions
®
Monogram.
We bring good things to life.
Краткое содержание страницы № 2
Safety Information • IMPORTANT – The dishwasher MUST BEFORE YOU BEGIN be installed to allow for future removal from the Read these instructions completely and carefully. enclosure if service is required. • IMPORTANT - Save these instructions for If you received a damaged dishwasher, you should local inspector’s use. Observe all governing immediately contact your dealer or builder. codes and ordinances. • Note to Installer - Be sure to leave these instruc- READ CAREFULLY. tions with the Consumer.
Краткое содержание страницы № 3
Design Information PRODUCT DIMENSIONS ADVANCE PLANNING • These dishwashers are designed for versatility, adaptable to virtually any installation. • All models have a full length door or a modified door to accept a full cabinet panel without the 34" traditional access panel Adjustable to 35" • Side tub flange trim is adjustable and will conceal *Dishwasher model any slight gap between the dishwasher and adjacent ZBD7000 and Chef’s Washer cabinetry. model ZBD7005 • These dishwashers may be instal
Краткое содержание страницы № 4
Installation Preparation MATERIALS YOU WILL NEED: Materials Required for All Installations Screw Type Clamps ¨ 90° Elbow (3/8”NPT external thread on one end, opposite 90° Elbow end sized to fit water supply) Note: Use new ferrule. Do not use old parts. ¨ Strain relief for electrical connection ¨ Thread seal tape Strain Relief Wire Nuts Thread Seal ¨ UL Listed wire connectors (3) Tape ¨ Screw type hose clamps Materials For New Installations Only: ¨ Air gap for drain hose, if required ¨ Waste tee
Краткое содержание страницы № 5
Installation Preparation PARTS SUPPLIED: Remove the hardware accessory bag and other parts from inside or taped to the outside of the dishwasher. Check contents against illustrations to insure that all Template parts are included. for ZBD7000 ZBD7005 ¨ 2-piece toekick Only ¨ 6 screws (see illustration) ¨ 2 leveling legs Junction Box Cover ¨ Template for the installation of a with screws 2 Leveling Legs Template with Mounting Hardware custom panel packed with models ZBD7000 and ZBD7005
Краткое содержание страницы № 6
Installation Preparation DRAIN REQUIREMENTS Method 1 – Air Gap with Waste Tee or Disposer • Follow local codes and ordinances. An air gap must be used when the waste tee or disposer connection is less than 18” from the floor. • Do not exceed 10 feet distance to drain. • To prevent back flow into the dishwasher, connect drain line to an air gap or use a 30” high drain loop, depending on local codes. • Air gap must be used when waste tee or disposer connection is less than 18” above the floor to
Краткое содержание страницы № 7
Installation Preparation PREPARE ELECTRICAL WIRING FOR PERSONAL SAFETY: Remove Alternate house fuse or open circuit breaker Receptacle before beginning installation. Do not use Location an extension cord or adapter plug with 18" this appliance. 1-1/2" Dia. Hole (Max.) Receptacle Location 18" Area 3" 6" 6" AVERTISSEMENT from POUR ASSURER LA SÉCURITÉ 2" Cabinet PERSONNELLE, il faut enlever le fusible 2" 24" ou couper le courant au disjoncteur from Wall avant de commencer l’installation. Avec cet a
Краткое содержание страницы № 8
Installation Preparation PREPARE HOT WATER LINE The line may enter from either side, rear or floor within the shaded area shown. • The water line may pass through the same hole as the electrical cable and drain hose. Or, cut an additional 1-1/2" dia. hole to admit the line. If a Right Side Entry 1-1/2" Shut-off Valve Approx. 40" power cord with plug is used, it must pass through Dia. 1-3/4" from Wall Hole a separate hole. Hot Water Line Connection 6" • Turn off the water supply. • Install a h
Краткое содержание страницы № 9
Custom Panel Dimensions CUSTOM PANEL FOR MODELS CUSTOM PANEL FOR MODELS ZBD6400 ONLY ZBD7000 AND ZBD7005 Panel kits must be ordered separately. Installation of any custom panel should be completed before These models require a field installed 3/4" thick custom the dishwasher is installed. panel and custom handle. An installation template is packed with these models and may be obtained in advance. Order Pub. No. 31-5912. See page 15 for panel installation instructions. 1/4" PANEL WITH ZPF625 TRIM
Краткое содержание страницы № 10
Installation Instructions STEP 3 REMOVE ACCESS COVER BEFORE YOU BEGIN: CUSTOM PANEL INSTALLATION: If you intend to install custom door panels, (on some models) refer to trim kit installation instructions. Custom panels should be in place before installing the dishwasher. Insulation Board STEP 1 REMOVE PACKAGING Cut the shipping carton and use it as a pad beneath the Junction Box dishwasher. This will protect the finished floor in the kitchen. Access Cover • Remove wrapping and uncoil the drain
Краткое содержание страницы № 11
Installation Instructions STEP 5 INSTALL POWER CORD STEP 7 SLIDE DISHWASHER INTO OPENING SKIP THIS STEP IF DISHWASHER WILL BE DIRECT WIRED DO NOT PUSH AGAINST THE FRONT PANEL WITH • Maximum power cord length is 6 ft. KNEES, DAMAGE WILL OCCUR! • The power cord and connections must comply with • Insert drain hose into the cabinet wall hole. If a power the National Electrical Code, Section 422 and/or cord is used, guide the end through a separate hole. local codes and ordinances. Insert power c
Краткое содержание страницы № 12
Installation Instructions STEP 9 CONNECT DRAIN LINE STEP 10 CONNECT ELECTRICAL FOLLOW ALL LOCAL CODES AND ORDINANCES. FOR DIRECT WIRE ONLY (If a power cord with plug is used, plug it into the wall • The dishwasher is supplied with a 72" long drain hose. outlet and continue with next step.) • If a longer drain hose is required, add up to 48” of length for a total of 10 ft. length. Verify that power is • Secure the drain hose to the air gap, waste tee or turned off at the disposer with clamps
Краткое содержание страницы № 13
U U N N S S C C Installation Instructions STEP 11 POSITION AND LEVEL THE DISHWASHER • Check to be sure the dishwasher is adjusted to correct Door Rub Door Rub height and is centered in the cutout. On Right On Left • Open and close the door to insure proper operation of Hand Side Hand Side the door. If there is any binding or rubbing, readjust Adjust Adjust leveling legs. This This Leg Leg Use a wrench to make adjustments. • If the door rubs on the right side of the cabinet, extend the left rear
Краткое содержание страницы № 14
Installation Instructions STEP 14 SECURE DISHWASHER STEP 15 INSTALL TOEKICK TO CABINET AND • Loosen depth COUNTERTOP adjustment screws inside the To maintain position and alignment, the dishwasher Adjust to bracket. must be secured to the countertop and adjacent Toekick • Slide bracket out Depth cabinets. to proper depth. Secure dishwasher to countertop: Tighten screws. • Drill pilot holes through the mounting bracket and • Attach supplied into the underside of the countertop. Secure with to
Краткое содержание страницы № 15
Panel Installation for Models ZBD7000 and ZBD7005 The custom panel should be prepared by your STEP 4 INSTALL CUSTOM HANDLE cabinet manufacturer according to the instructions Screws Must shown on page 9. Use the supplied installation Be Countersunk template to locate the mounting screws for the Into Panel 4-1/2" Max. door. From Top of Panel STEP 1 DRAW Handle CENTERLINE Custom • Place the custom panel on a Door Panel flat surface with appearance A custom handle must be installed onto the panel
Краткое содержание страницы № 16
Note: While performing installations described in this book, safety glasses or goggles should be worn. TM For Monogram local service in your area, call 1-800-444-1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. 0616 400 327 ® Pub. No. 49-5905 Monogram. Dwg. No. 165D4700P231 (N.D. 131) 11/01 General Electric Company Louisville, KY 40225
