Руководство по эксплуатации Fisher & Paykel DD605I

Краткое содержание страницы № 1

Integrated panel preparation
DS605I and DD605I models
DishDrawer
NZ AU GB IE

Краткое содержание страницы № 2

Safety and warnings WARNING! Cut Hazard Take care - panel edges are sharp. Failure to use caution could result in injury or cuts. Important! Read these instructions completely and carefully. Ensure the product is not plugged in. Installation of DishDrawer® panels requires basic mechanical and electrical skills. Installation must comply with your local building and electricity regulations. Failure to install the DishDrawer panels correctly could invalidate any warranty or liabili

Краткое содержание страницы № 3

1 Contents Double models Product preparation 2 Single models Product preparation 4 Panel Installation Badge cut-out, handle and mounting bracket 6 Securing the mounting brackets 7 Reconnecting the wires and fitting the 8 panels and a custom toe kick (double models only) Important! SAVE THESE INSTRUCTIONS The models shown in this User Guide may not be available in all markets and are subject to change at any time. For current details about model and specific

Краткое содержание страницы № 4

toe kick panel 2 Product preparation Double DishDrawer models A min. 5 mm B C D 8 mm Air gap height of toe kick panel min. 12 mm Installation diagrams for illustration purposes only The following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry. The fi nal panel/cabinetry alignment is achieved by adjusting the feet: width of ALL panels Measure A (the width between adjacent door/drawer fronts) and write it in the fi rst box below, then complete

Краткое содержание страницы № 5

R12.7 mm 3 Product preparation Toe kick preparation height of toe kick panel Measure D (height from the top of adjacent cabinet door fronts to the fl oor) and write it in the fi rst box below, then complete the equation. height height toe kick panel D B D B toe kick panel i.e 817.5 mm - 0 mm - 735 mm - 12 mm = 70.5 mm - - 735 mm - 12 mm = height adjacent door DishDrawer® cabinetry extension dimension min. clearance (min. 70.5 mm) Toe kick optio

Краткое содержание страницы № 6

4 Product preparation Single DishDrawer models A min. 5 mm B 9 mm Air gap 9 mm Air gap Installation diagrams for illustration purposes only The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry: width of the panel Measure A (the width between adjacent door/drawer fronts) and write it in the fi rst box below, then complete the equation. A door clearance panel width A door clearance panel width i.e 600 mm - 2 x 2.5 mm = 595 mm

Краткое содержание страницы № 7

5 Product preparation 9 mm 9 mm Air gap Air gap Integrated Panel material 16 -20 mm panel thickness O Adequately sealed to withstand moisture (50 C @ 80% RH) Parts supplied Panel mounting screws (6) Integrated rectangular badge (1) (Satin chrome supplied) Mounting bracket (1) Integrated door seal (1) panel Use this diagram if installing the DishDrawer® near floor level.

Краткое содержание страницы № 8

Badge zone Badge zone 228.5 mm 228.5 mm 6 Badge cut-out, handle and mounting bracket Installation diagrams feature double models for illustration purposes only 1 Important! Ensure the product is not plugged in 2 3 1 2 1 4 127 mm 211 mm 54 mm 127 mm 30 mm 25 mm

Краткое содержание страницы № 9

7 Securing the mounting brackets 3 1 2 4 2 16 mm x6 1 Double models only: Important! Break off the tab at the top of the Lower Mounting Bracket 3

Краткое содержание страницы № 10

8 Reconnecting the wires and fi tting the panels and a custom toe kick (double models only) 5 2 1 6 Important! Ensure the rubber seal between the drawer and panels is kept in place 2 16 mm x 5 16 mm x5 1 2

Краткое содержание страницы № 11

9

Краткое содержание страницы № 12

Copyright © Fisher & Paykel 2007. All rights reserved. The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available. www.fisherpaykel.com NZ AU GB IE DishDrawer integrated panel preparation Published: 06/2007 Part No. 52