Краткое содержание страницы № 1
USER’S MANUAL
Part 2
1719 Digital
Answering System
Fold open this manual for information about
this product’s installation and operation.
Please also read Part 1 – Important Product
Information.
AT&T and the Globe Design are trademarks of AT&T Corp. licensed to Advanced American Telephones.
© 2002 Advanced American Telephones. All rights reserved.
Printed in China. Issue 1AT&T 12/02
Visit us at www.telephones.att.com
© 2002 Advanced American Telephones.
All rights reserved.
AT&T and the Glob
Краткое содержание страницы № 2
INSTALLATION Before You Install Choose a location for the answering Use only the power cord system near a modular telephone jack and supplied with this product. a standard electrical outlet not controlled If you need a replacement, by a wall switch. call 1 800 222–3111. Input: 120 V, 60 Hz. NOTE: If you do not want to connect a Output: 6V AC, 350 mA. telephone, skip Step 2. Standard Electrical Outlet 1 Connect the telephone line cord. Strain-relief 2 Connect the tab telephone (optional). 3 Con
Краткое содержание страницы № 3
FEATURE SETUP Feature Setup 1 To enter Feature Setup mode, press 4 Press and release S to set up and hold S until the system the next feature listed on the announces “Number of rings is…” Feature Summary — OR — 2 Press and release S until the Press and release P to exit system announces the feature you Feature Setup. want to set. The new settings will be saved. 3 Press and release a or r until the system 5 After you have selected the feature announces the setting you want. options, you can revi
Краткое содержание страницы № 4
FEATURE SETUP Feature Summary (continued) Feature/System Announces Options Number Announce When this feature is on, the system will announce (Please see NOTE below.) the caller’s telephone number between the second and third rings. “Number announce is...” NOTE: When the Number Announce feature is on and Ring Select is set for two rings, the unit will answer after three rings to allow enough time for the system to announce the caller’s telephone number. Store Number When this feature is on, th
Краткое содержание страницы № 5
OPERATION 2 To stop recording, release a. Set the Clock The system automatically plays back You must set the clock once so that the your announcement. system announces the correct day and time with your messages. After this, if you To review your announcement, press subscribe to Caller ID, the system will and release a. automatically reset the clock each time To erase your announcement and new call information is received. return to the pre-recorded announcement, Press P to exit at any time whi
Краткое содержание страницы № 6
OPERATION line. The system stops recording and resets the message playing. Before playing each to answer calls. If the system doesn’t message, the system announces the day disconnect immediately, press and release and time the message was received. If the the telephone switchhook. clock wasn’t set when the message was recorded, either because you didn’t set the Caller ID Number Announce clock or because there was a power failure after you set it, the system will announce NOTE: For these feat
Краткое содержание страницы № 7
OPERATION Memory is Full the system plays an error tone and does not delete messages. When memory is full, or 100 messages have been recorded, the Message Window Delete selected messages — Press and flashes F. Delete messages to make room release D while the message you for new ones. want to delete is being played. The system deletes the message and plays the next When memory is full, the system answers message. If you want to check a message calls after 10 rings, and sounds two beeps before
Краткое содержание страницы № 8
OPERATION Listen To, Save & Delete Messages • The system automatically saves your announces the caller’s telephone messages until you delete them. You number (see “Store Number” under can store approximately 19 minutes of FEATURE SETUP). After playing the messages, memos, and announcements last message, the system announces (up to a maximum of 100 messages). “End of messages.” • Before playing each message, the • You cannot delete a message until it’s system announces the day and time been rev
Краткое содержание страницы № 9
REMOTE OPERATION Connect with the Answering System You can access many features remotely entering your code, wait for the from a touch tone phone. announcement to end or press # to stop the announcement, then 1 Dial your telephone number. re-enter the code. 2 When the system answers, enter your 3 To use a remote access command three-digit Remote Access Code during (below), press 5 during message or after the announcement. The system playback and wait for the two-beep announces the number of mes
Краткое содержание страницы № 10
IN CASE OF DIFFICULTY If you have difficulty operating this • The answering system may not detect product, try the suggestions below. the Remote Access Code while your For Customer Service, visit our announcement is playing. Try waiting website at www.telephones.att.com or until the announcement is over before call 1 800 222–3111. Please retain your entering the code. receipt as your proof of purchase. • There may be noise interference on the phone line you are using. Press Messages Are Incom
