Краткое содержание страницы № 1
Network Camera User’s Guide
Pan and Tilt
Network Camera
User’s Guide
Software Version 2.1.7
1/95
Краткое содержание страницы № 2
Network Camera User’s Guide PT IP Cam / IR IP Cam / Video Server Series © 2004~2005. Owner's Record The model and serial numbers are located at the bottom. Record these numbers in the spaces provided below. Refer to these numbers whenever you call upon your dealer regarding this product. Model No. ______________ Serial No. ____________________ To prevent fire or shock hazard, do not expose the unit to rain or moisture. For AC Adaptor to avoid electrical shock, do not open the cabi
Краткое содержание страницы № 3
Network Camera User’s Guide Declaration of Conformity This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTICE TO USERS © 2004~2005. All rights reserved. This manual or the software described herein, in whole or in part, may not be reproduced, translated
Краткое содержание страницы № 4
Network Camera User’s Guide Table of Contents Overview ............................................................................................................................. 6 Package Contents................................................................................................................ 8 Connections....................................................................................................................... 11 Hardware Installation........................
Краткое содержание страницы № 5
Network Camera User’s Guide Schedule ....................................................................................... 49 Motion Detection.......................................................................... 50 Time Setting ................................................................................. 51 Popup............................................................................................ 53 Firmware upgrade:.........................................................
Краткое содержание страницы № 6
Network Camera User’s Guide Overview This user’s guide explains how to operate the Network Camera from a computer. Basically, the user’s guide is written to be read on the computer display. However, users might consider printing it out to access easily and read it before you operate the Network Camera. Introduction This Network Camera is an inexpensive fully scalable surveillance technology. Because the Network Cameras can be plugged in to your existing computer network infrastructu
Краткое содержание страницы № 7
Network Camera User’s Guide Application: Remote monitoring Surveillance Minimum System Requirement Microsoft Internet Explorer 5.0 or later VGA Monitor resolution 1024 x 768 Pentium 4 1.3GHz or above Memory Size: 256MB or above Windows ME, 2000, XP, or 2003 7/95
Краткое содержание страницы № 8
Network Camera User’s Guide Package Contents User can find the following items in the package: 1. PT Network Camera x 1 2. Power adapter x 1 3. Power cord x 1 4. Decoration ring x 1 5. Screw x 4 6. Terminator for Alarm I/O x 1 7. Installation software and manual CD x 1 8. Quick Start Guide x 1 Item Descriptions 1. This unit is the main element of the system. 2. Switching Power Adapter dedicates 12V DC electric power output to Network Camera. 8/95
Краткое содержание страницы № 9
Network Camera User’s Guide 3. Power Cord provides connection between AC Power Adapter and Power Outlet for electricity. 4. Decorate the mounting parts. Provide four screw holes to fix Network Camera. 5. Screws are used to fix Network Camera. 6. Alarm I/O connector is used to provide an easy fixing interface for the wire connection from alarm devices and sensor devices to Network Camera. 7. User’s Manual provides important information and instructions for operating the Ne
Краткое содержание страницы № 10
Network Camera User’s Guide 8. Quick Start Guide provides important information and instructions for installing this device. If any of the above items are missing, please contact your dealer immediately. Note: Using a power supply with a different voltage than the one included with the Network Camera will cause damage and void the warranty for this product. 10/95
Краткое содержание страницы № 11
Network Camera User’s Guide Connections DC Power and Video Output Cable The DC power input and video output cable are located on the Network Camera’s back panel. The input power is 12VDC. Note that supply the power to the Network Camera with standard power adapter included in package. Otherwise, the improper power adapter may damage the unit and result in danger. The Network Camera also provides composite video output. User can use BNC video cable to connect the Network Camera wi
Краткое содержание страницы № 12
Network Camera User’s Guide Alarm I/O Connector The Network Camera provides a terminal block with 8 pins of connectors located on the center of the back panel. There are 3 pins for two alarm inputs and 5 pins are for alarm output. The I/O connectors are physical interface to sense and/or activate alarm signals to a variety of external sensors or alarms. Please refer to the Appendix B in this manual for more information. CF Card Socket The CF card socket is located on the right side of
Краткое содержание страницы № 13
Network Camera User’s Guide Hardware Installation 1. Fix the Network Camera to Ceiling Use 4 screws to fix the Network Camera onto the ceiling as below. You can also put the Network Camera on the table directly. 2. Plug an Ethernet cable into Network Camera Connect an Ethernet cable to the LAN socket located on the Network Camera’s back panel and attach it to the network. 13/95
Краткое содержание страницы № 14
Network Camera User’s Guide 3. Connect the external power supply to Network Camera Connect the external power supply to the DC power connector attached on the extension cable from the Network Camera. Note: Use the power adapter, 12VDC, included in the package and connect the other end to wall outlet for AC power. Once you have installed the Network Camera well, the status LED will turn orange. It means the system is booting up successfully. Furthermore, if you have a proper network con
Краткое содержание страницы № 15
Network Camera User’s Guide Logging in to Homepage Before Operation Install the IP Address of Network Camera When you installed your Network camera on your LAN environment, you may execute IPFINDER.EXE to discover Network camera’s IP address. IPCam Finder program (IPFINDER.EXE) is used to scan the Installed Network Camera, setting the Network Camera Name, IP address settings and so on. Using your mouse to select any one of the Network Cameras within your LAN environment,
Краткое содержание страницы № 16
Network Camera User’s Guide 1. Edit the Name of this Network Camera. Note that use “_” or “-“ to replace “space” character to separate the name string. For example, “PT_IP” or “PT-IP” will be right. However “PT IP” will not work here. 2. Might be needed to update the IP address of this Network Camera. ( Power recycling might be necessary) 3. Might be needed to update the Gateway Address. ( Power recycling might be necessary) 4. Might be needed to update the Network Mask (255.255.255.0)
Краткое содержание страницы № 17
Network Camera User’s Guide First time uses the Network Camera The Network Camera web page communicates with the Network Camera using an ActiveX control. The ActiveX control must be downloaded from the Network Camera and installed on your PC. Your Internet Explorer security settings must allow for the web page to work correctly. To use the Network Camera, user must setup his IE browser as follows: From your IE browse ”Tools” ”Internet Options…” ”Security” ”Custom Level…”,
Краткое содержание страницы № 18
Network Camera User’s Guide By now, you have finished your entire PC configuration for Network Camera. 18/95
Краткое содержание страницы № 19
Network Camera User’s Guide Access the Network Camera from the Internet Explorer for the first time 1. Start the web browser on the computer and type the IP address of the Network Camera you want to monitor as below: The Login Window of the Network Camera is displayed: 2. Type in your login name and password under “USERNAME” and “PASSWORD” textbox. For the first time use (default value), input the User Name: admin Password: 19/95
Краткое содержание страницы № 20
Network Camera User’s Guide That’s, type in “admin” on the “USERNAME” as a default name and leave PASSWORD textbox blank. Click “OK” button to start the main menu. Now, you login to the Network Camera as a full-authorized administrator. You can enter “Setting” to change the password and setup “Administrator” or “User” authority. Please refer to “Setting” “User” and “IP Filter”. 3. The IE Web Page will display the “Security Warning” window, select “Yes” to install and run the A
