Краткое содержание страницы № 1
Краткое содержание страницы № 2
WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER, NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE ENGINEER. DISCONNECT FROM MAINS SUPPLY WHEN NOT IN USE FOR LONG PERIODS. POWER SOURCES AC 110-240 Volts 50Hz or DC 12 Volts Only WARNING Never connect the AC power cord to any other voltages other than the one specified. Use the attached power cord only. NOTE: Disconnect from the housing outlet when not in use for a
Краткое содержание страницы № 3
FEATURES AC/DC Power Operation • On Screen Programming • Daily 4 event Programmable ON/OFF Timer • Auto Tuning for Channel Presetting • 110 Preset Channel • Sleep Timer (Up to 120 minutes) • Child Lock (Hotel Lock) • Automatic Power Shut Off • 24:00 Clock Timer • 2 Speaker • AUDIO/VIDEO IN & OUT Jack • 5 Language on Screen Menu • Picture Adjustment • CATV Capability • NTSC 3.58/4.43 - PLAYBACK ON PAL 60Hz • CONTENTS PREPARATIONS LOCATION OF CONTROLS ..............................................
Краткое содержание страницы № 4
Краткое содержание страницы № 5
Краткое содержание страницы № 6
(Continued) REMOTE CONTROL BATTERY INSTALLATION Use two "UM-4" size batteries. Replace the cover. Slide the cover in the Load the two batteries direction of the arrow as shown below. and remove. NOTE: Your TV will not work in the following cases. Check them carefully. If direct sunlight or other strong light is If there is an obstacle between the TV shining on the remote control sensor. and the remote control handset. If the polarities, + and –, are wrongly If the batteries are weak. aligned. 4
Краткое содержание страницы № 7
ANTENNA CONNECTIONS Connect the cable from the outdoor or indoor antenna to the antenna jack on the rear panel as shown below. For all antenna circuit problems, please consult your local dealer. A) A twin-lead telescopic antenna is supplied with the unit. Insert the B) antenna post into the mounting hole on the back cabinet until it locks into place. Insert the antenna adaptor A) (supplied) to the antenna jack. Adjust the length and angle of both antenna rods to receive the best possible picture
Краткое содержание страницы № 8
Краткое содержание страницы № 9
PRESETTING THE CHANNELS After connecting, preset the desired channel (up to 110 channels) in the following procedure. There are two types of station presettings you may choose from: - Automatic tuning All stations will be preset in sequence available in your area. - Manual tuning You activate the auto search function until your preferred station is tuned in. Then you memorize this station into the chosen channel memory. For each station you repeat the same procedure. AUTOMATIC TUNING Press the M
Краткое содержание страницы № 10
PRESETTING THE CHANNELS (Continued) MANUAL TUNING - How to tune a station to channel 10 position. Press the SET UP or DOWN button Press the MENU button. 1 2 to select the MANUAL mode, then Press the SET UP or DOWN button to select the CH TUNING mode, then press the ENTER button. press the ENTER button. MENU SET ENTER SET ENTER CLOCK SET ON/OFF TIMER SET CH TUNING CH TUNING MANUAL PICTURE AUTO LANGUAGE CH ALLOCATION PRESS:+/-/ENTER/MENU PRESS:+/-/ENTER/MENU Press the SET UP or DOWN button unt
Краткое содержание страницы № 11
Press the SET UP or DOWN button Repeat step 3 through 4 until all the 4 5 required channels have been stored. to select channel position No.10, then press the ENTER button. SET ENTER 3 4 PAL CH 10 When all desired channels have been set in your required position, press the MENU 6 button three times to return to normal TV screen. MENU 9
Краткое содержание страницы № 12
PRESETTING THE CHANNELS (Continued) TO CHANGE THE CHANNELS EXAMPLE: Changing of channel position from CH2 to CH5. Press the MENU button. Press the SET UP or DOWN button to 2 1 Press the SET UP or DOWN button to select the CH ALLOCATION mode, select the CH TUNING mode, then then press the ENTER button. press the ENTER button. MENU SET ENTER CLOCK SET SET ENTER ON/OFF TIMER SET CH TUNING CH TUNING MANUAL PICTURE AUTO CH ALLOCATION LANGUAGE PRESS:+/-/ENTER/MENU PRESS:+/-/ENTER/MENU Press the S
Краткое содержание страницы № 13
TV OPERATIONS (Continued) After completing the connection and presetting the channels, follow these steps for viewing. Press the POWER button on the TV. Then press POWER button on the remote 1 control to turn off (STAND BY indication will light up) or on (STAND BY indication will goes off). POWER POWER Direct Channel Selection buttons (0-9) CHANNEL UP and DOWN buttons 2 Press the Direct Channel Selection Press CHANNEL UP/DOWN button on button on the remote control. the remote control. 1-9 CH: Pr
Краткое содержание страницы № 14
Краткое содержание страницы № 15
Краткое содержание страницы № 16
SETTING THE ON / OFF TIMER (Continued) Press the SET UP or DOWN button Press the SET UP or DOWN button 6 5 to set the desired minute, then press to set the desired channel (only to set the ENTER button. the ON TIMER), then press the ENTER button. SET ENTER SET ENTER ON TIMER ON TIMER 7: 30 CH 1 CANCEL 7: 30 CH 3 CANCEL 0: 00 CH 1 CANCEL 0: 00 CH 1 CANCEL 0: 00 CH 1 CANCEL CH 1 0: 00 CANCEL 0: 00 CH 1 CANCEL 0: 00 CH 1 CANCEL OFF TIMER OFF TIMER 0: 00 CANCEL 0: 00 CANCEL 0: 00 CANCEL
Краткое содержание страницы № 17
CONVENIENT FUNCTIONS The following functions are available from the remote control handset only. TV/AV Selection For receiving the desired signal: Press the AV select button to select the TV or AV mode. PAL CH 5. PAL AV 0 AV TV position - to view a normal TV. AV position - to receive through the direct Video input. VIDEO indicator appears on the screen in AV mode. QUICK VIEW This button allows you to go back to the previous channel by pressing the QUICK VIEW button. Press this button agai
Краткое содержание страницы № 18
CONVENIENT FUNCTIONS (Continued) MUTE When the MUTE button is pressed, the TV sound system will be turned off completely. To disable this function, press the button again. To control the volume, press VOLUME UP/DOWN. MUTE MUTE SLEEP To set the sleep timer, press the SLEEP button on the remote control. The timer will change in step of 10 minutes each time the button is pressed in the order of 120, 110, 100,...20, 10, 0. After the sleep time is programmed, the display will disappear and will reapp
Краткое содержание страницы № 19
PICTURE CONTROL (Continued) The picture setting have been adjusted at the factory under optimum signal reception conditions. However, you can adjust for BRIGHTNESS, CONTRAST, COLOUR, SHARPNESS and TINT to your preference. Press the MENU button. Press the SET UP or DOWN button 1 2 to select the PICTURE mode, then press the ENTER button. MENU SET ENTER CLOCK SET ON/OFF TIMER SET CH TUNING PICTURE LANGUAGE PRESS:+/-/ENTER/MENU To adjust the BRIGHTNESS, press the SET UP or DOWN button, then press
Краткое содержание страницы № 20
(Continued) PICTURE CONTROL To adjust the COLOUR, press the To adjust the CONTRAST, press 3-c 3-b the SET UP or DOWN button, then SET UP or DOWN button, then press the ENTER button. press the ENTER button. Picture looks sharpest in the daytime by The control should be set to where colors appear normal in intensity and brilliance. increasing the contrast. At night, the sharpest picture is obtained by reducing the contrast. SET ENTER SET ENTER CONTRAST -10 COLOUR 17 To adjust the SHARPNESS, press
