Краткое содержание страницы № 7
Getting started Installation preparation You must install and charge See pages 7-8 the battery before using the for easy instructions. telephone. STOP! If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL) through your telephone lines, you must install a DSL filter between the telephone base and the telephone wall jack (see page 5). The filter will prevent noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more in
Краткое содержание страницы № 8
WALL WALL DESK DESK Getting started Telephone base installation If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL) through your telephone lines, you must install a DSL filter between the telephone base and the telephone wall jack. The filter will prevent noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters. Install the telephone base as shown below. 1. Plug the small 2. Plug one
Краткое содержание страницы № 9
Getting started Charger installation 1. Plug the small end 2. Plug the large end of the smaller power of the smaller power adapter into the jack adapter into a power on the underside of the outlet not controlled charger, then route the by a wall switch. cord through the slot as shown. IMPORTANT INFORMATION 1. Use only the power adapter supplied with this product. To order a replacement power adapter, visit our website at www.telephones.att.com, or call 1 (800) 222-3111. In Canada, d
Краткое содержание страницы № 10
Getting started Battery installation & charging Install the battery as shown below. After installing the battery, you can make and receive short calls, but replace the handset in the telephone base or additional charger when not in use. For optimal performance, charge the handset battery for at least 16 hours before use. When fully charged, the handset battery provides approximately five hours of talk time and three days of standby time. If the battery is depleted, it may take approximately
Краткое содержание страницы № 11
Getting started Battery installation & charging Step 4 Charge the handset by placing the handset face up in the telephone base or in the additional charger. The CHARGE light will be on when charging. IMPORTANT INFORMATION Use only the battery supplied with this product. To order a replacement or spare battery (AT&T model 27910, part number 89-0099-00-00) or equivalent, visit our website at www.telephones.att.com, or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. 8
Краткое содержание страницы № 12
Getting started Belt clip & optional headset To remove the belt To attach the clip: belt clip: Gently lift either of the Snap the belt clip belt clip retaining tabs, into the retaining shown in the figure, tabs on both sides outwards to remove of the handset as the belt clip from the shown in the figure. handset. For handsfree headset conversations, use any industry standard 2.5 mm headset (purchased separately). For best results, use an AT&T 2.5 mm headset. To purchase a headset, v
Краткое содержание страницы № 13
Getting started Installation options NOTE: The mounting bracket must be used for both tabletop use and wall mounting positions. The telephone base comes with the mounting bracket already installed for desktop use. If wall mounting is desired, a telephone outlet wall mounting plate with mounting studs is required. This mounting plate with studs may be available for purchase from many handware or consumer electronics retailers and may require professional installation. Desktop to wall mount
Краткое содержание страницы № 14
Getting started Installation options Desktop to wall mount installation (continued) 2. Plug the telephone line cord and power adapter into the telephone base. Bundle the telephone line cord and power adapter cord, and secure them with a twist tie before placing them in the bracket channels. WALL DESK DESK DESK DESK DSL filter (not included), required if you have DSL high-speed Internet service. 3. Place the bundled telephone line cord and power adapter cord into the cavity WALL under the
Краткое содержание страницы № 15
Getting started Installation options Wall mount to desktop installation To change the telephone base from the wall mount position to desktop position. 1. Make sure that you unplug the power adapter and telephone line cord from the wall outlets before you begin. 2. Untie the bundled telephone line cord and power adapter cord, and remove them from the telephone base. Side view 3. Push the bottom of the bracket down towards the back of the telephone base. With the bottom of the bracke
Краткое содержание страницы № 16
Getting started Installation options Wall mount to desktop installation (continued) 4. Plug the telephone line cord into the telephone base and telephone wall jack, then plug the power adapter plug into the telephone base and an electrical wall outlet not controlled by a wall switch (see page 5) and place the cords in the bracket channels. Telephone line cord DSL filter (not included), required if you have DSL high-speed Internet service. Power adapter Telephone wall jack 13 WALL WALL DES
Краткое содержание страницы № 17
Telephone operation Handset operation Making a call Elapsed To make a call: time • Press PHONE/FLASH or SPEAKER, then enter PHONE 0:00:30 the telephone number. To end a call: • Press OFF/CLEAR or return the handset to the telephone base or charger. The screen displays the elapsed time as you talk (in hours, minutes and seconds). NOTE: Pressing On-hook dialing (predialing) PHONE/FLASH to • Enter the telephone number. Press access services from MUTE/REMOVE or OFF/CLEAR to make yo
Краткое содержание страницы № 18
Telephone operation Handset operation Answering a call To answer a call: • Press PHONE/FLASH or SPEAKER. –OR– • Press any dial pad key (0-9, * or #). To end a call: • Press OFF/CLEAR or return the handset to the telephone base or charger. Auto off A call will be ended automatically when you put the handset in the telephone base or charger. Last number redial To view the five most recently dialed numbers: REDIAL • Press REDIAL/PAUSE to display the most 555-1234 recently called number (up to 3
Краткое содержание страницы № 19
Telephone operation Handset operation Handset locator The handset locator feature is useful if you misplace a handset. To start the paging tone: • Press HANDSET LOCATOR at the telephone base. This starts the paging tone at the handset(s) for 60 seconds to help you locate the handset(s). NOTE: When paging, if you press OFF/CLEAR or MUTE/REMOVE on a handset, the ringer of the handset will be silent but the handset locator feature will not be canceled. To stop the paging tone: • Press PH
Краткое содержание страницы № 20
Telephone operation Options while on calls Volume control Press the VOLUME keys on the side of the handset to adjust listening volume. Each press of the button increases or decreases the volume. NOTES: Volume 1. All volume settings (normal handset, speakerphone and control headset) are independent. 2. When the volume level has reached the minimum or maximum setting, you will hear two beeps. Call waiting If you subscribe to call waiting service with your local telephone service provider,