Руководство по эксплуатации Polycom SPECTRALINK 6000

Краткое содержание страницы № 1

Installing the Outdoor
Base Station
SpectraLink 6000 System
July 2008 Edition
1725-36127-001
Version F

Краткое содержание страницы № 2

Installing the Outdoor Base Station Trademark Information Notice Polycom® and the logo designs Polycom, Inc. has prepared this document for use by Polycom personnel SpectraLink® and customers. The drawings and LinkPlus specifications contained herein are the Link property of Polycom and shall be neither NetLink reproduced in whole or in part without SVP the prior written approval of Polycom, Are trademarks and registered nor be implied to grant any license to trademarks of Pol

Краткое содержание страницы № 3

About this Guide The Outdoor Base Station is designed to withstand environmental hazards such as rain and excessive heat and cold. The outdoor enclosure is mounted into position and the Base Station is then installed within it. The entire unit is then referred to as an Outdoor Base Station. This document covers the installation of the Outdoor Base Station in a variety of situations. It supplements the installation documentation for the SpectraLink 6000 System using either the Spect

Краткое содержание страницы № 4

Installing the Outdoor Base Station For Technical Support: technicalsupport@polycom.com For Knowledge Base: http://www.polycom.com/usa/en/support/voice/voice.html For Return Material Authorization: rmacoordinator@polycom.com 4 1725-36127-001-F.doc

Краткое содержание страницы № 5

Contents 0 About this Guide ................................................3 Polycom Corporation Model Numbers 3 Related Documents 3 Contacting Polycom 3 1 Installing Flush Against a Wall or Hard Ceiling....6 2 Installing on an I-Beam.......................................8 3 Installing on a Light Pole or Electrical Pole .........10 1725-36127-001-F.doc 5

Краткое содержание страницы № 6

1 Installing Flush Against a Wall or Hard Ceiling Items provided: Outdoor enclosure, Base Station Items needed: 4 anchor bolts (length and type depends on wall or ceiling material Base Station is being mounted to) 1. Mark and drill four holes into the wall or ceiling, using the mounting flanges of the outdoor enclosure as a guide. 2. Mount outdoor enclosure to wall or ceiling using anchor bolts. The outdoor enclosure can be mounted with the compression fitting in any direct

Краткое содержание страницы № 7

Installing Flush Against a Wall or Hard Ceiling 4. Crimp an RJ45 onto the Base Station cable using the same wiring guide as the indoor Base Station. 5. Plug the RJ45 into the RJ48C connector. Mounting hole RJ48C connector 6. Place the Base Station into the enclosure with the side of the Base Station with the mounting hole facing the wall or ceiling. The Base Station should fit tightly into the foam blocks. 7. Screw the outdoor enclosure lid back onto the enclosure. 1725-36127-00

Краткое содержание страницы № 8

2 Installing on an I-Beam Items provided : Outdoor enclosure, Base Station Items needed : 4 – “Caddy” or “B-Line” 3/8” Beam Clamps 4 – 1/2” long 1/4” x 20 bolts 4 – 2” long 1/4” x 20 bolts 4 – 1/4” x 20 nuts 1. Attach a beam clamp to the center of the top and bottom flanges on the outdoor enclosure. 2. Attach a second beam clamp to each of the beam clamps on the enclosure using a 1/2” long 1/4” x 20 bolt and a nut. (See figure below.) 3. Attach the outdoor enclosure t

Краткое содержание страницы № 9

Installing on an I-Beam 7. Place the Base Station into the enclosure with the side of the Base Station with the mounting hole facing the I-beam. The Base Station should fit tightly between the foam blocks. 8. Screw the outdoor enclosure lid back onto the enclosure. 1725-36127-001-F.doc 9

Краткое содержание страницы № 10

3 Installing on a Light Pole or Electrical Pole Items provided: Outdoor enclosure, Base Station Items needed: 4 - “Caddy” or “B-Line” 3/8” beam clamps 2 - EOG 100 or equivalent band clamps 1. Attach one band to the top flange of the outdoor enclosure using two beam clamps (see the figure below). 2. Attach the second band to the bottom flange of the enclosure using the remaining two beam clamps. 3. Wrap the band clamps around the pole and tighten using the screw on the band clamp

Краткое содержание страницы № 11

Installing on a Light Pole or an Electrical Pole 7. Place the Base Station into the enclosure with the side of the Base Station with the mounting hole facing the pole. The Base Station should fit tightly between the foam blocks. 8. Screw the outdoor enclosure lid back onto the enclosure. 1725-36127-001-F.doc 11

Краткое содержание страницы № 12

PN: 1725-36127-001-F.doc