Resumo do conteúdo contido na página número 1
model t23094
pneumatic metal shear
oWner's manual
Copyright © ApriL, 2011 By grizzLy industriAL, inC.
Warning: no portion of this manual may be reproduced in any shape
or form Without the Written approval of grizzly industrial, inc.
#Cr14035 printed in ChinA
Resumo do conteúdo contido na página número 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to
Resumo do conteúdo contido na página número 3
t able of contents safety ............................................................................................................................2 safety instructions for pneumatic tools .....................................................................2 Additional safety instructions for pneumatic shears .................................................3 section 1: introduction .........................................................................................4 Foreword ..........
Resumo do conteúdo contido na página número 4
safety For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indic
Resumo do conteúdo contido na página número 5
use proper air hose for the tool. Wear approved hearing Make sure your air hose is in good protection . Air escaping from condition and is long enough to reach pneumatic tools can exceed safe your work without stretching. exposure limits and may cause hearing damage with prolonged exposure. secure W or K. u se clamps or a vise to hold work when practical. it is safer than air line connection inspection . using your hand and frees both hands to An air line that becomes disconnected operate
Resumo do conteúdo contido na página número 6
section 1: introduction f oreword c ontact info We are proud to offer this manual with We stand behind our products. if you have your new t 23094! We've made every any service questions, parts requests effort to be exact with the instructions, or general questions about the product, specifications, drawings, and photographs please call or write us at the location listed of the t23094 we used when writing below. this manual. h owever, sometimes we still make an occasional mistake. g rizzly i
Resumo do conteúdo contido na página número 7
identification Body Head Angled Slide 1 ⁄4" Quick Disconnect Fitting Removed Trigger Jaw Set Filter Jaw Retaining Screen Cap Screws Swivel Head Cap Screw Exhaust Port figure 1. Components and controls. t his tool presents serious injury hazards to untrained users. r ead through this entire manual to become familiar with the controls and opera- tions before using the tool! Model t23094 pneumatic Metal shear -5-
Resumo do conteúdo contido na página número 8
section 2: setup unpacking assembly your tool was carefully packaged for safe t o assemble the pneumatic shear: transportation. r emove the packaging 1. remove the plastic plug from the air materials from around your tool and inspect inlet in the handle. it. if you discover the tool is damaged, please immediately call Customer Service 2. Apply pipe sealant on the threads of at (570) 546-9663 for advice. the quick disconnect fitting. s ave the containers and all packing 3. thread the fitting
Resumo do conteúdo contido na página número 9
section 3: operations o peration o verview t o complete a typical cutting operation, the following is done: 1. put on safety goggles and gloves. 2. Mark the cut line, secure the workpiece, and clamp a guide to the workpiece if t his tool presents serious injury needed. hazards to untrained users. r ead through this entire manual to become 3. determine if the swivel head needs to familiar with the controls and opera- be rotated for optimum tool control and tions before using the tool! cu
Resumo do conteúdo contido na página número 10
section 4: accessories 1 t23103—12" slip roll t 20881—in-l ine l ubricator ⁄4" npt 1 t his slip roll is just the ticket for live t 20887—pressure r egulator ⁄4" npt 1 steamers, model makers and small g 6261—Water f ilter ⁄4" npt jobbers. With its 12" ground and polished install an in-line lubricator to apply oil rolls it can handle mild steel up to 22 automatically. install an air regulator right 5 15 5 gauge and also has ⁄32", ⁄64" and ⁄16" at the tool for precise air control. install a diam
Resumo do conteúdo contido na página número 11
g8780—portable hand punch. t10172—sheet metal shrinker stretcher producing 1 ton of force, this h and punch Make smooth radius curves in sheet has a 16 gauge capacity in mild steel, metal without cutting, welding, heating brass and aluminum. Much or hammering. t his tool shrinks sheet quicker and safer than drilling thin stock metal on one side for inside curves and and leaves no ragged edges. includes expands sheet metal on the opposite side 3 1 5 3 7 1 9 ⁄32", ⁄8", ⁄32", ⁄16", ⁄32", ⁄4" a
Resumo do conteúdo contido na página número 12
section 5: maintenance accidental start hazard ! disconnect before service. air pressure eye inJury hazard ! hazard ! Wear safety goggles with full eye never exceed max protection from all sides when psi rating for tool. using or servicing this shear. lubrication daily maintenance in most cases for perodic tool use, manual before and after each use: lubrication is sufficiant. h owever, if the tool • Check and replace any leaking air is to be used on a consistent basis, we fittings; bu
Resumo do conteúdo contido na página número 13
section 6: service t roubleshooting important : a ir tool repairs must be completed by a qualified service person. symptom possible cause solution t ool runs at 1. pneumatic shear is being 1. reduce feed pressure. only cut normal speed but overloaded. materials within limits of tool. bogs down when 2. Jaws are dull or loose. 2. dress or replace jaws. cutting, or tool 3. trigger is at fault. 3. remove any metal that may be runs slowly with binding trigger from full travel. little air exiting t
Resumo do conteúdo contido na página número 14
symptom possible cause solution t ool does not 1. Motor is at fault. 1. Motor may be stuck in position operate when the from improper storage. trigger is pressed, Lubricate the air tool, remove but air runs freely the swivel head cap screw from exhaust. and the head. using a 17mm wrench, rotate the spindle back and forth slightly a few times. next operate the air tool while re-oiling several times in the process to flush the tool. 2. Motor or gearing is at fault. 2. replace tool. t ool
Resumo do conteúdo contido na página número 15
section 7: parts main parts diagram Parts breakdown provided for reference only. Not all parts 21 23 shown are available 25 24 for purchase. 26 27 20 32 29 31 30 4 42 33 35 2 28 12 13 40 14 7 16 6 1 41 15 38 8 22 3 17 9 36 39 42 37 19 5 18 11 10 main parts l ist REF PART # DESCRIPTION REF PART # DESCRIPTION 1 N/A AIR INLET 22 N/A THROTTLE CYLINDER 2 N/A EXHAUST SLEEVE 23 N/A SHAFT 3 N/A DUST PLUG 24 N/A INTERNAL RING GEAR 4 N/A MOTOR HOUSING 25 P6201Z BALL BEARING 6201 Z 5 N/A COMPRESSION SPRIN
Resumo do conteúdo contido na página número 16
Warranty Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any par- ticular purpose, are hereby limited to the duratio
